Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.     

Analytical study of ground motion caused by seismic wave propagation across faulted rock masses

Studying seismic wave propagation across rock masses and the induced ground motion is an important topic, which receives considerable attention in design and construction of underground cavern/tunnel constructions and mining activities. The current study investigates wave propagation across a rock mass with one fault and the induced ground motion using a recursive approach. The rocks beside the fault are assumed as viscoelastic media with seismic quality factors, Q_p and Q_s. Two kinds of interactions between stress waves and a discontinuity and between stress waves and a free surface are analyzed, respectively. As the result of the wave superposition, the mathematical expressions for induced ground vibration are deduced. The proposed approach is then compared with the existing analysis for special cases. Finally, parametric studies are carried out, which includes the influences of fault stiffness, incident angle, and frequency of incident waves on the peak particle velocities of the ground motions.     

Explicit stress–strain equations for modeling frictional materials

In this paper, a comprehensive study on simulating the shearing behavior of frictional materials is performed. A set of two explicit equations, describing the relationship among the shear stress ratio and the distortional strain and the volumetric strain, are formulated independently. The equations contain three stress parameters and three strain parameters and another parameter representing the nonuniformity of stress and strain during softening. All the parameters have clear physical significance and can be determined experimentally. It is demonstrated that the proposed equations have the capacity of simulating the complicated shearing behavior of many types of frictional materials including geomaterials. The proposed equations are used to simulate the stress–strain behavior for 27 frictional materials with 98 tests. These materials include soft and stiff clays in both reconstituted and structured states, silicon sands and calcareous sands, silts, compacted fill materials, volcanic soils, decomposed granite soils, cemented soils (both artificially and naturally cemented), partially saturated soils, ballast, rocks, reinforced soils, tire chips, sugar, wheat, and rapeseed. It has been demonstrated that the proposed explicit constitutive equations have the capacity to capture accurately the shearing behavior of frictional materials both qualitatively and quantitatively. A study on model parameters has been performed.     

Spatial measurements of stream baseflow,a relevant method for aquifer characterization and permeability evaluation. Application to a hard‐rock aquifer,the Oman ophiolite

The structure, functioning and hydrodynamic properties of aquifers can be determined from an analysis of the spatial variability of baseflow in the streams with which they are associated. Such analyses are based on simple low‐cost measurements. Through interpreting the hydrological profiles (Q = f(A)) it is possible to locate the aquifer(s) linked to the stream network and to determine the type of interrelated flow, i.e. whether the stream drains or feeds the aquifer. Using an analytical solution developed for situations with a positive linear relationship, i.e. where the baseflow increases linearly with increasing catchment size, it is also possible to estimate the permeability of the aquifer(s) concerned at catchment scale. Applied to the hard‐rock aquifers of the Oman ophiolite, this method shows that the ‘gabbro’ aquifer is more permeable than the ‘peridotite’ aquifer. As a consequence the streams drain the peridotites and ‘leak’ into the gabbro. The hydrological profiles within the peridotite are linear and positive, and indicate homogeneity in the hydrodynamic properties of these formations at the kilometre scale. The permeability of the peridotite is estimated at 5 · 10^?7 to 5 · 10^?8 m/s. Copyright © 2004 John Wiley & Sons, Ltd.     

隧道工程地质评价的内容和方法

结合工程隧道实际,首先阐述了隧道工程的基本地质环境和工程地质条件,然后针对隧道工程可能出现的不良地质现象和可采取的工程措施,从大气降水、围岩稳定、围岩压力、洞口稳定、隧道比选等角度探讨隧道工程地质评价的主要方法和一般内容,进行隧道工程地质评价,为隧道施工、支护提供了依据.     

P‐wave transmission across fractures with nonlinear deformational behaviour

Stress wave attenuation across fractured rock masses is a great concern of underground structure safety. When the wave amplitude is large, fractures experience nonlinear deformation during the wave propagation. This paper presents a study on normal transmission of P‐wave across parallel fractures with nonlinear deformational behaviour (static Barton–Bandis model). The results show that the magnitude of transmission coefficient is a function of incident wave amplitude, nondimensional fracture spacing and number of fractures. Two important indices of nondimensional fracture spacing are identified, and they divide the area of nondimensional fracture spacing into three parts (individual fracture area, transition area and small spacing area). In the different areas, the magnitude of transmission coefficient has different trends with nondimensional fracture spacing and number of fractures. In addition, the study reveals that under some circumstances, the magnitude of transmission coefficient increases with increasing number of fractures, and is larger than 1. Copyright © 2006 John Wiley & Sons, Ltd.     

Solution to the rotation of the elastic earth by method of rigid dynamics

Hamiltonian mechanics is applied to the problem of the rotation of the elastic Earth. We first show the process for the formulation of the Hamiltonian for rotation of a deformable body and the derivation of the equations of motion from it. Then, based on a simple model of deformation, the solution is given for the period of Euler motion, UT1 and the nutation of the elastic Earth. In particular it is shown that the elasticity of the Earth acts on the nutation so as to decrease the Oppolzer terms of the nutation of the rigid Earth by about 30 per cent. The solution is in good agreement with results which have been obtained by other, different approaches.     

北秦岭晋宁期中酸性侵入岩带地球化学特征与构造环境

北秦岭侵入岩带中的中酸性侵入岩主要形成于晋宁旋回的中晚期阶段。主要岩石类型包括辉石闪长岩、闪长岩、石英闪长岩、英云闪长岩、花岗闪长岩、斜长花岗岩、花岗岩和钾长花岗岩。岩石化学、稀土元素和微量元素地球化学研究证明,这些岩石主要形成于B型俯冲和碰撞造山的构造环境中,而钾长花岗岩形成于后造山的伸展阶段。据此,该侵入岩带揭示了北秦岭褶皱带在晋宁旋回中晚期阶段的演化过程。     

有限元法与伪谱法混合求解弹性波动方程

在地震波场数值模拟中,有限差分法、有限元法和伪谱法都是常用的基本方法,但它们各有不同的适应性和优缺点,如有限差分法、有限元法都存在减弱网格频散和提高计算效率的矛盾,而伪谱法的网格频散小且计算效率高.有限差分法和伪谱法在处理地表结构复杂或地表剧烈起伏以及地下结构复杂的情况时存在较大的难度,而有限元法可较为理想地拟合起伏地表和任意弯曲界面,且可方便地处理自由边界条件和界面边界条件.尝试将有限元法和伪谱法相结合,形成地震波场数值模拟的一种混合方法,利用二者的优点,克服二者的缺点,达到既减弱网格频散又提高计算精度和效率的目的.并采用所谓的‘过度区域‘技术解决两种不同算法的衔接问题.模拟实例表明,给出的混合模拟方法不失为弹性波场数值模拟的一种有效方法.     

模糊划分矩阵在岩土参数概率分布中的应用

讨论如何在小样本条件下用已有的过程经验与试验资料确定岩土参数概率分布,用模糊划分矩阵与BAYES方法相结合,给出由小样本试验数据确定岩土参数的概率分布。