Stable carbon isotopes of alkane gases from the Xujiahe coal measures and implication for gas-source correlation in the Sichuan Basin,SW China

The Upper Triassic Xujiahe Formation in the Sichuan Basin, SW China consists of a series of coal measures. The first, third and fifth members of this formation are dominated by gas prone dark mudstones and coals. The mudstones contain Type II and III kerogens with average organic carbon contents around 1.96%. These source rocks are mature in the central Sichuan and highly mature in the western Sichuan Basin, characterized by gas generation with subordinate amounts of light oil or condensate oils. The source rocks are intercalated with the sandstone dominated second, fourth and sixth members of the Xujiahe Formation, thus leading to three separate self contained petroleum systems in the region. The proven gas reserves in the Xujiahe Formation are only less than that of the Triassic Feixianguan Formation and the Xujiahe Formation has the second largest gas field (Guang’an gas field) in the basin. Gases derived from the Xujiahe Formation coals generally show a normal stable carbon isotopic trend for C₁–C₄ n-alkanes, with the highest δ¹³C₂ values among the nine gas pay zones in the basin (?20.7‰ to ?28.3‰), and δ¹³C₁ values as low as ?43.0‰ in the central Sichuan. Gas accumulations with an oil leg have also been found in the eastern and southern Sichuan where the thickness of the Xujiahe Formation is significantly reduced. Gases in these accumulations tend to show low δ¹³C₂ values (?30.0‰ to ?36.3‰), characteristic of oil prone source rocks.     

Geochemical comparison between gas in fluid inclusions and gas produced from the Upper Triassic Xujiahe Formation,Sichuan Basin,SW China

Natural gas in the Xujiahe Formation of the Sichuan Basin is dominated by hydrocarbon (HC) gas, with 78–79% methane and 2–19% C₂₊ HC. Its dryness coefficient (C₁/C_1–5) is mostly < 0.95. The gas in fluid inclusions, which has low contents of CH₄ and heavy hydrocarbons (C₂₊) and higher contents of non-hydrocarbons (e.g. CO₂), is a typical wet gas produced by thermal degradation of kerogen. Gas produced from the Upper Triassic Xujiahe Formation (here denoted field gas) has light carbon isotope values for methane (δ¹³C₁: −45‰ to −36‰) and heavier values for ethane (δ¹³C₂: −30‰ to −25‰). The case is similar for gas in fluid inclusions, but δ¹³C₁ = −36‰ to −45‰ and δ¹³C₂ = −24.8‰ to −28.1‰, suggesting that the gas experienced weak isotopic fractionation due to migration and water washing. The field gas has δ¹³C_CO2 values of −15.6‰ to −5.6‰, while the gas in fluid inclusions has δ¹³C_CO2 values of −16.6‰ to −9‰, indicating its organic origin. Geochemical comparison shows that CO₂ captured in fluid inclusions mainly originated from source rock organic matter, with little contribution from abiogenic CO₂. Fluid inclusions originate in a relatively closed system without fluid exchange with the outside following the gas capture process, so that there is no isotopic fractionation. They thus present the original state of gas generated from the source rocks. These research results can provide a theoretical basis for gas generation, evolution, migration and accumulation in the basin.     

Characteristics and Natural Gas Origin of Middle−Late Triassic Marine Source Rocks of the Western Sichuan Depression, SW China

A scientific exploration well(CK1) was drilled to expand the oil/gas production in the western Sichuan depression, SW, China. Seventy-three core samples and four natural gas samples from the Middle–Late Triassic strata were analyzed to determine the paleo-depositional setting and the abundance of organic matter(OM) and to evaluate the hydrocarbon-generation process and potential. This information was then used to identify the origin of the natural gas. The OM is characterized by medium n-alkanes(n C_(15)–n C_(19)), low pristane/phytane and terrigenous aquatic ratios(TAR), a carbon preference index(CPI) of ～1, regular steranes with C_(29) C_(27) C_(28), gammacerane/C_(30) hopane ratios of 0.15–0.32, and δD_(org) of-132‰ to-58‰, suggesting a marine algal/phytoplankton source with terrestrial input deposited in a reducing–transitional saline/marine sedimentary environment. Based on the TOC, HI index, and chloroform bitumen "A" the algalrich dolomites of the Leikoupo Formation are fair–good source rocks; the grey limestones of the Maantang Formation are fair source rocks; and the shales of the Xiaotangzi Formation are moderately good source rocks. In addition, maceral and carbon isotopes indicate that the kerogen of the Leikoupo and Maantang formations is type Ⅱ and that of the Xiaotangzi Formation is type Ⅱ–Ⅲ. The maturity parameters and the hopane and sterane isomerization suggest that the OM was advanced mature and produced wet–dry gases. One-dimensional modeling of the thermal-burial history suggests that hydrocarbon-generation occurred at 220–60 Ma. The gas components and C–H–He–Ar–Ne isotopes indicate that the oilassociated gases were generated in the Leikoupo and Maantang formations, and then, they mixed with gases from the Xiaotangzi Formation, which were probably contributed by the underlying Permian marine source rocks. Therefore, the deeply-buried Middle–Late Triassic marine source rocks in the western Sichuan depression and in similar basins have a great significant hydrocarbon potential.     

Origin and Source of Deep Natural Gas in Nanpu sag,Bohai Bay Basin,China

Natural gas exploration in Nanpu sag, Bohai Bay Basin, has achieved breakthroughs in recent years, and a number of natural gas and condensate wells with high yield have been found in several structures in the beach area. Daily gas production of single wells is up to 170,000 m3, and high-yield wells are mainly distributed in?the Nanpu No. 1 structural belt.?Studies have shown that these natural gases are mainly hydrocarbon gases, with methane content about 80% to 90% and ethane 6%-9%, so they are mainly wet gas; and non-hydrocarbons are at a low level.?Carbon isotopes of methane range from -42‰ to -36‰, and ethane from -28‰ to -26‰. Calculated maturity based on the relationship between δ13C and Ro of natural gas, the gases are equivalent to those generated from organic matter when Ro is 1.0%-1.7% (mainly 1.25%-1.32%). The natural gas is oil-type gas generated from the source rocks at mature to high mature stage, associated with condensate, so carbon isotopes of the gases are heavier. Natural gas in the Nanpu No.1 structural belt is mainly associated gas with condensate. The analysis of the origin and source of natural gas and condensate, combined with the monomer hydrocarbon carbon isotopes and biomarker, indicated that the main source rocks in the Nanpu No.1 structural belt were Es3 (the lower member of the Shahejie Formation), followed by Es1 (the upper member of the Shahejie Formation).?The high-mature hydrocarbons from source rocks in the deep sag mainly migrated through deep inherited faults into shallow traps and accumulated to form oil and gas pools. Therefore, there is a great potential for exploring gas in deep layers.     

Characteristics and Evaluation of the High-Quality Source Rocks of Cretaceous Continental Shale Oil in Tonghua Basin,China

The presence of shale oil in the Cretaceous Hengtongshan Formation in the Tonghua Basin, drilled by the well TD-01, has been discussed in this geological investigation for the first time. To evaluate the high-quality source rocks of Cretaceous continental shale oil, the distribution characteristics and the evolution of the ancient environment, samples of shale were systematically analyzed in terms of sedimentary facies, organic geochemistry, and organic carbon isotopic composition. The results demonstrate that a TOC value of 1.5% represents the lower-limit TOC value of the high-quality source rocks. Source rocks have an aggregate thickness of 211 m and contain abundant organic matter, with TOC values of 2.69% on average and a maximum value over 5.44%. The original hydrocarbon-generative potential value(S_1+S_2) is between 0.18 mg/g and 6.13 mg/g, and the Ro is between 0.97% and 1.40%. The thermal maturation of the source rocks is relatively mature to highly mature. The δ¹³C value range is between -34.75‰ and -26.53‰. The ratio of saturated hydrocarbons to aromatic hydrocarbons is 1.55 to 5.24, with an average of 2.85, which is greater than 1.6. The organic types are mainly type Ⅱ_1, followed by type Ⅰ. The organic carbon source was C_3 plants and hydrophytes. The paleoclimate of the Hengtongshan Formation can be characterized as hot and dry to humid, and these conditions were conducive to the development of high-quality source rocks. A favorable paleoenvironment and abundant organic carbon sources provide a solid hydrocarbon generation base for the formation and accumulation of oil and gas in the shale of the Tonghua Basin.     

塔里木盆地喀什凹陷克拉托天然气来源分析及聚气特征

塔里木西南喀什凹陷的克拉托天然气主要表现为原油的溶解气或者湿气,甲烷含量为74.59%~85.58%,克4井和克30井天然气则为较干的湿气。克拉托天然气的δ¹³C₁值为-41.2‰~-40.6‰,δ¹³C₂值为-30.0‰~-27.4‰。气源对比表明克拉托天然气主要源自具有混源母质特征的中侏罗统湖相烃源岩,不同于源自石炭系烃源岩的阿克莫木天然气。喀什凹陷的中-下侏罗统烃源岩主要是由于新近系的巨厚沉积才从未成熟—低成熟阶段进入成熟—高成熟阶段,生成的油气在克拉托背斜圈闭中聚集,虽也属晚期成藏,却具有连续聚气的特征。上新世末期,喀什凹陷的周缘开始抬升,早期油气藏受到破坏,形成了现今的地表油气苗或油砂。     

Gas Sources of Natural Gas Hydrates in the Shenhu Drilling Area, South China Sea: Geochemical Evidence and Geological Analysis

The Shenhu gas hydrate drilling area is located in the central Baiyun sag, Zhu Ⅱ depression, Pearl River Mouth basin, northern South China Sea. The gas compositions contained in the hydrate-bearing zones is dominated by methane with content up to 99.89% and 99.91%. The carbon isotope of the methane (δ13C1 ) are 56.7‰ and 60.9‰, and its hydrogen isotope (δD) are 199‰ and 180‰, respectively, indicating the methane from the microbial reduction of CO2 . Based on the data of measured seafloor temperature and geothermal gradient, the gas formed hydrate reservoirs are from depths 24-1699 m below the seafloor, and main gas-generation zone is present at the depth interval of 416-1165 m. Gas-bearing zones include the Hanjiang Formation, Yuehai Formation, Wanshan Formation and Quaternary sediments. We infer that the microbial gas migrated laterally or vertically along faults (especially interlayer faults), slump structures, small-scale diapiric structures, regional sand beds and sedimentary boundaries to the hydrate stability zone, and formed natural gas hydrates in the upper Yuehai Formation and lower Wanshan Formation, probably with contribution of a little thermogenic gas from the deep sedments during this process.     

Kinetic Model of Gaseous Alkanes Formed from Coal in a Confined System and Its Application to Gas Filling History in Kuqa Depression, Tarim Basin, Northwest China

Based on the pyrolysis products for the Jurassic low-mature coal under programmed temperature,and chemical and carbon isotopic compositions of natural gas from the Kuqa Depression, the genetic origin of natural gas was determined,and then a gas filling model was established,in combination with the geological background of the Kuqa Depression.The active energy of CH_4,C_2H_6 and C_3H_8 was gotten after the data of pyrolysis gas products under different heating rates(2℃/h and 20℃/h)were fitted by the Gas O...     

Geology and Isotope Geochemistry of the Yinchanggou-Qiluogou Pb-Zn Deposit, Sichuan Province, Southwest China

The Yinchanggou-Qiluogou Pb-Zn deposit,located in the western Yangtze Block,southwest China,is hosted by the Upper Sinian Dengying Formation dolostone.Ore bodies occur in the Qiluogou anticline and the NS-and NNW-trending faults.Sulfide ores mainly consist of sphalerite,pyrite,galena and calcite,with subordinate dolomite and quartz.Seventeen ore bodies have been discovered to date and they have a combined 1.0 million tons of sulfide ores with average grades of 2.27wt%Zn and 6.89wt%Pb.The δD_(H2O-SMOW) and δ~(18)O_(H2O-SMOW) values of fluid inclusions in quartz and calcite samples range from-68.9‰ to-48.7‰ and 7.3‰ to 15.9‰,respectively,suggesting that H_2O in the hydrothermal fluids sourced from metamorphic water.Calcite samples have δ~(13)C_(PDB) values ranging from-6.2‰ to-4.1‰ and δ~(18)O_(SMOW) values ranging from 15.1‰ to 17.4‰,indicating C and O in the hydrothermal fluids likely derived from a mixed source of metamorphic fluids and the host carbonates.The δ~(34)S_(CDT) values of sulfide minerals range from 5.5‰ to 20.3‰,suggesting that thermal chemical reduction of sulfate minerals in evaporates were the most probable source of S in the hydrothermal fluids.The ~(206)Pb/~(204)Pb,~(207)Pb/~(204)Pb and ~(208)Pb/~(204)Pb ratios of sulfide minerals fall in the range of 18.11 to 18.40,15.66 to 15.76 and 38.25 to 38.88,respectively.The Pb isotopic data of the studied deposit plot near the upper crust Pb evolution curve and overlap with the age-corrected Proterozoic basement rocks and the Upper Sinian Dengying Formation hosting dolostone.This indicates that the Pb originated from a mixed source of the basement metamorphic rocks and the ore-hosting carbonate rocks.The ore geology and C-H-O-S-Pb isotopic data suggest that the YinchanggouQiluogou deposit is an unusual carbonate-hosted,strata-bound and epigenetic deposit that derived ore-forming materials from a mixed source of the underlying Porterozoic basements and the Sinian hosting carbonates.     

Origin and Accumulation of Natural Gases in the Upper Paleozoic Strata of the Ordos Basin in Central China

The natural gases in the Upper Paleozoic strata of the Ordos basin are characterized by relatively heavy C isotope of gaseous alkanes with δ 13C1 and δ13C2 values ranging mainly from ?35‰ to ?30‰ and ?27‰ to ?22‰, respectively, high δ13C excursions (round 10) between ethane and methane and predominant methane in hydrocarbon gases with most C1/(C1-C5) ratios in excess of 0.95, suggesting an origin of coal-derived gas. The gases exhibit different carbon isotopic profiles for C1-C4 alkanes with those of the natural gases found in the Lower Paleozoic of this basin, and believed to be originated from Carboniferous-Permian coal measures. The occurrence of regionally pervasive gas accumulation is distinct in the gently southward-dipping Shanbei slope of the central basin. It is noted that molecular and isotopic composition changes of the gases in various gas reservoirs are associated with the thermal maturities of gas source rocks. The abundances and δ13C values of methane generally decline northwards and from the basin center to its margins, and the effects of hydrocarbon migration on compositional modification seem insignificant. However, C isotopes of autogenetic calcites in the vertical and lateral section of reservoirs show a regular variation, and are as a whole depleted upwards and towards basin margins. Combination with gas maturity gradient, the analysis could be considered to be a useful tool for gas migration.     

Geochemical Characteristics and Genetic Types of Natural Gas in the Xinchang Gas Field, Sichuan Basin, SW China

The molecular compositions and stable carbon and hydrogen isotopic compositions of natural gas from the Xinchang gas field in the Sichuan Basin were investigated to determine the genetic types. The natural gas is mainly composed of methane (88.99%–98.01%), and the dryness coefficient varies between 0.908 and 0.997. The gas generally displays positive alkane carbon and hydrogen isotopic series. The geochemical characteristics and gas-source correlation indicate that the gases stored in the 5~(th) member of the Upper Triassic Xujiahe Formation are coal-type gases which are derived from source rocks in the stratum itself. The gases reservoired in the 4~(th) member of the Xujiahe Formation and Jurassic strata in the Xinchang gas field are also coal-type gases that are derived from source rocks in the 3~(rd) and 4~(th) members of the Xujiahe Formation. The gases reservoired in the 2~(nd) member of the Upper Triassic Xujiahe Formation are mainly coal-type gases with small amounts of oil-type gas that is derived from source rocks in the stratum itself. This is accompanied by a small amount of contribution brought by source rocks in the Upper Triassic Ma'antang and Xiaotangzi formations. The gases reservoired in the 4~(th) member of the Middle Triassic Leikoupo Formation are oil-type gases and are believed to be derived from the secondary cracking of oil which is most likely to be generated from the Upper Permian source rocks.     

A Study of the Migration and Accumulation Efficiency and the Genesis of Hydrocarbon Natural Gas in the Xujiaweizi Fault Depression

In order to investigate the migration and accumulation efficiency of hydrocarbon natural gas in the Xujiaweizi fault depression, and to provide new evidence for the classification of its genesis, a source rock pyrolysis experiment in a closed system was designed and carried out. Based on this, kinetic models for describing gas generation from organic matter and carbon isotope fractionation during this process were established, calibrated and then extrapolated to geologic conditions by combining the thermal history data of the Xushen-1 Well. The results indicate that the coal measures in the Xujiaweizi fault depression are typical ＂high-efficiency gas sources＂, the natural gas generated from them has a high migration and accumulation efficiency, and consequently a large-scale natural gas accumulation occurred in the area. The highly/over matured coal measures in the Xujiaweizi fault depression generate coaliferous gas with a high δ^13C1 value （〉 -20‰） at the late stage, making the carbon isotope composition of organic alkane gases abnormally heavy. In addition, the mixing and dissipation through the caprock of natural gas can result in the negative carbon isotope sequence （δ^13C1 〉δ^13C2 〉δ^13C3 〉δ^13C4） of organic alkane gases, and the dissipation can also lead to the abnormally heavy carbon isotope composition of organic alkane gases. As for the discovery of inorganic nonhydrocarbon gas reservoirs, it can only serve as an accessorial evidence rather than a direct evidence that the hydrocarbon gas is inorganic. As a result, it needs stronger evidence to classify the hydrocarbon natural gas in the Xujiaweizi fault depression as inorganic gas.     

Characteristics of Breccias and C-O-Sr-S Isotope Geochemistry of the Duocaima Pb-Zn Deposit in Tuotuohe, Qinghai Province: Implications for the Ore-forming Process

The Duocaima carbonate-hosted Pb-Zn deposit is a newly found large deposit in the southern area of Qinghai Province.In this paper, the characteristics, genesis, significance to Pb-Zn mineralization of the widely developed breccias, and the ore-forming process have been carefully studied based on geological documentation of drilling holes, microscopic observations of petrography and microstructure and some stable isotope measurements.Based on the compositions of the clast and matrix, the breccias can be classified into three types: limestone clasts cemented by marl; limestone clasts with fine-grained calcareous materials; and limestone clasts cemented by hydrothermal calcite.The mineralization in the first type of breccia is weak, whereas it is strong in the latter two types of breccias.According to the locations of occurrence and structural characteristics of the breccias along with the relationship between the breccias and mineralization, part of the limestone clasts that are cemented by marl and outcrop in the contact zone between the Wudaoliang Formation(Nw) and the underlying Jiushidaoban Formation(Pj) are attributed to synsedimentary fault-genetic breccia, whereas the last of the limestone clasts that are cemented by marl and developed in the Jiushidaoban Formation(Pj) are attributed to the breccia generated by karst cave collapse; the limestone clasts with fine-grained calcareous materials and the limestone clasts cemented by hydrothermal calcite are attributed to breccia formed by hydrothermal dissolution.The breccia formed by karst collapse had consistently evolved for a long period of time, while the breccias with other origins were formed around the period of mineralization(i.e., about or slightly later than 20–16 Ma).The breccia generated by karst cave collapse and hydrothermal dissolution are somewhat related; the formation of the breccia from karst cave collapse provided open space for the later mineralization and reaction between hydrothermal fluids and host rocks, and the subsequent strong dissolution by hydrothermal fluids transformed some of the breccia formed earlier by karst cave collapse.Meanwhile, carbonate host rocks with breccias and brecciaed mineralization can be a potential sign of Mississippi Valley Type(MVT) deposits and important indicators for regional mineral exploration.The δ13CV-PDB, δ18OVSMOW, and 87Sr/86 Sr values of hydrothermal calcite in the Duocaima deposit range from 4.3‰ to 7.1‰, 14.9‰ to 20.1‰, and 0.707494 to 0.708185, respectively; the δ13CV-PDB, δ18OV-SMOW, and 87Sr/86 Sr values of the host limestones of the Jiushidaoban Formation range from 3.6‰ to 5.3‰, 18.0‰ to 20.5‰, and 0.707372 to 0.707945, respectively.The δ13CV-PDB and 87Sr/86 Sr values of hydrothermal calcite and limestone are similar, indicating single sources of C and Sr in this deposit, with the likely source being the limestone of the Jiushidaoban Formation.The minor scattering of the δ18OV-SMOW values suggests that different O isotope fluids underwent the isotope exchange reaction.The C-O-Sr isotope characteristics indicate that the host limestones experienced a dissolution and precipitation process during mineralization, which is beneficial to improving the porosity of host rocks and promoting the precipitation of metal sulfides.The δ34SV-CDT value of the breccia-type mineralization sulfides ranges from-30.4‰ to-0.3‰; that is, the δ34SV-CDT value is negative with considerable variation, illustrating that during the breccia-type mineralization process, the bacteriogenic reduction of sulfates provided the vast majority of sulfur, whereas the thermochemical reduction of sulfates was relatively unimportant.The brecciation that occurred as a result of karst cave collapse was mainly generated by the dissolution of groundwater; however, the brecciation related to hydrothermal dissolution and mineralization processes were caused by mixing of different fluids.     

Geological and Geochemical Characteristics and Exploration Prospect of Coal‐Derived Tight Sandstone Gas in China: Case Study of the Ordos,Sichuan, and Tarim Basins

This work extensively investigated global tight sandstone gas, and geologically and geochemically analyzed the tight sandstone gas in China's Ordos, Sichuan, and Tarim basins. We compared typical tight sandstone gas in China with that in North America. We proposed six conditions for the formation of China's tight sandstone gas, and illustrated the geological characteristics of tight sandstone gas. In China, gas-bearing tight sandstones were mainly deposited in continental lake deltas and marine-terrigenous facies basin environments, associated with coal-measure strata, and were mostly buried deeper than 2000 m under a formation pressure of 20–30 MPa, with pressure coefficients varying from overpressure to negative pressure. In other countries, tight gas bearing sandstones were dominantly deposited in marine to marine-terrigenous facies environments, occurred in coal-measure strata, and were mostly buried shallower than 2000 m in low-pressure systems. We systematically analyzed tight sandstone gas in the Ordos, Sichuan, and Tarim basins in terms of chemical compositions, geochemical characteristics of carbon isotopes, origins, and sources. Tight sandstone gas in China usually has a hydrocarbon content of 95%, with CH4 content 90%, and a generally higher dry coefficient. In the three above-mentioned large tight sandstone gas regions, δ13 C1 and δ13 C2 mainly ranges from-42‰ to-28‰ and from-28‰ to-21‰, respectively. Type III coal-measure source rocks that closely coexist with tight reservoirs are developed extensively in these gas regions. The organic petrology of source rocks and the carbon isotope compositions of gas indicate that tight sandstone gas in China is dominantly coal-derived gas generated by coal-measure strata. Our analysis of carbon isotope series shows that local isotope reversals are mainly caused by the mixing of gases of different maturities and that were generated at different stages. With increasing maturity, the reversal tendency becomes more apparent. Moreover, natural gas with medium-low maturity(e.g., Xujiahe Formation natural gas in the Sichuan Basin) presents an apparent reversal at a low-maturity stage, a normal series at a medium-maturity stage, and a reversal tendency again at a high-maturity stage. Finally, we proposed four conditions for preferred tight sandstone gas "sweep spots," and illustrated the recoverable reserves, proven reserves, production, and exploration prospects of tight sandstone gas. The geological and geochemical characteristics, origins, sources, and exploration potential of tight sandstone gas in China from our research will be instructive for the future evaluation, prediction, and exploration of tight sandstone gas in China and abroad.     

Effects of Deep Fluids on Hydrocarbon Generation and Accumulation in Chinese Petroliferous Basins

Deep fluids in a petroliferous basin generally come from the deep crust or mantle beneath the basin basement, and they transport deep substances(gases and aqueous solutions) as well as heat to sedimentary strata through deep faults. These deep fluids not only lead to large-scale accumulations of CO_2, CH_4, H_2, He and other gases, but also significantly impact hydrocarbon generation and accumulation through organic-inorganic interactions. With the development of deep faults and magmatic-volcanic activities in different periods, most Chinese petroliferous basins have experienced strong impacts associated with deep fluid activity. In the Songliao, Bohai Bay, Northern Jiangsu, Sanshui, Yinggehai and Pearl Mouth Basins in China, a series of CO_2 reservoirs have been discovered. The CO_2 content is up to 99%, with δ~(13)C_(CO2) values ranging from-4.1‰ to-0.37‰ and ~3He/~4He ratios of up to 5.5 Ra. The abiogenic hydrocarbon gas reservoirs with commercial reserves, such as the Changde, Wanjinta, Zhaozhou, and Chaoyanggou reservoirs, are mainly distributed in the Xujiaweizi faulted depression of the Songliao Basin. The δ~(13)CCH4 values of the abiogenic alkane gases are generally -30‰ and exhibit an inverse carbon isotope sequence of δ~(13)C_(CH4)δ~(13)C_(C2H6)δ~(13)C_(C3H8)δ~(13)C_(C4H10). According to laboratory experiments, introducing external H_2 can improve the rate of hydrocarbon generation by up to 147% through the kerogen hydrogenation process. During the migration from deep to shallow depth, CO_2 can significantly alter reservoir rocks. In clastic reservoirs, feldspar is easily altered by CO_2-rich fluids, leading to the formation of dawsonite, a typical mineral in high CO_2 partial pressure environments, as well as the creation of secondary porosity. In carbonate reservoirs, CO_2-rich fluids predominately cause dissolution or precipitation of carbonate minerals. The minerals, e.g., calcite and dolomite, show some typical features, such as higher homogenization temperatures than the burial temperature, relatively high concentrations of Fe and Mn, positive Eu anomalies, depletion of 18 O and enrichment of radiogenic ~(87)Sr. Due to CO_2-rich fluids, the development of high-quality carbonate reservoirs is extended to deep strata. For example, the Well TS1 in the northern Tarim Basin revealed a high-quality Cambrian dolomite reservoir with a porosity of 9.1% at 8408 m, and the Well ZS1 C in the central Tarim Basin revealed a large petroleum reserve in a Cambrian dolomite reservoir at ~6900 m. During the upward migration from deep to shallow basin strata, large volumes of supercritical CO_2 may extract petroleum components from hydrocarbon source rocks or deep reservoirs and facilitate their migration to shallow reservoirs, where the petroleum accumulates with the CO_2. Many reservoirs containing both supercritical CO_2 and petroleum have been discovered in the Songliao, Bohaiwan, Northern Jiangsu, Pearl River Mouth and Yinggehai Basins. The components of the petroleum trapped with CO_2 are dominated by low molecular weight saturated hydrocarbons.     

塔里木盆地西部阿克莫木气田形成初探

塔里木盆地西部阿克莫木气田天然气为非烃组份含量较高的干气,干燥系数高达99.7%;天然气δ¹³C₁和δ¹³C₂值明显偏重,δ¹³C₁为- 25.2‰～-21.9,δ¹³C₂为-21.2～-20.2‰,如果按传统的观点该天然气应为过成熟煤成气。但是综合气源对比研究表明阿克莫木气田天然气主要源自石炭系Ⅱ型烃源岩,成藏过程研究表明该气田主要聚集了石炭系烃源岩在Ro为1.5%～1.8%之后生成的天然气,具有晚期阶段聚气的特征,这是造成阿克1井天然气组份很“干”、碳同位素很重的主要原因。     

川西坳陷侏罗系天然气气源对比研究

川西坳陷侏罗系天然气具有δ13C1<δ13C2<δ13C3 的正常系列分布特征,为典型的热催化成因的煤型气,天然气母质类型主要为腐殖型。通过岩石组合特征分析,认为侏罗系天然气大部分来源于上三叠统须五段源岩,须四段和侏罗系本身源岩（如自流井组暗色泥岩）可能也有一定贡献;轻烃特征研究也说明了须五段源岩对侏罗系天然气有较大的贡献;δ13C1-Ro关系更进一步说明了侏罗系天然气主要来源于须五段烃源岩,而孝-新-合地区须四段和自流井组源岩可能有一定程度的贡献。     

Stable isotope(δ~(13)C_(ker),δ~(13)C_(carb),δ~(18)O_(carb)) distribution along a Cambrian outcrop section in the eastern Tarim Basin,NW China and its geochemical significance

This study investigated the geochemical features of the lower Paleozoic strata of Yaerdang Mountain outcrop along with the core samples from well TD2∈ in the eastern Tarim Basin,NW China.The total organic carbon abundance,hydrocarbon-generating precursor biospecies,and stable isotope ratios of organics and carbonate(δ~(13)C_(ker),δ~(13)C_(carb) and δ~(18)O_(carb)) were comprehensively studied for their possible correlative constraints during sedimentary evolution.The results revealed that the δ~(13)C_(ker)(VPDB) of Cambrian kerogens along the outcrop section varied from-34.6‰ to-28.4‰,indicating an increasing tendency from the lower Cambrian to the upper Cambrian.This was on the whole accompanied by the variation in the δ~(13)C_(carb) and δ~(18)O_(carb) along the profile,which might be associated with the changes in the sea level and also in the compositional variation of benthic and planktonic biomass.The large variation in the stable carbon isotope ratios up to 6‰ along the outcrop section reflected the heterogeneity of the Cambrian source rocks from the eastern Tarim Basin.Hence,the ~(13)C-enriched crude oils from well TD2∈might have been derived from a localized stratum of Cambrian source rocks.The results from this study showed the possibility of multiple source kitchens in the Cambrian-lower Ordovician portion of Tarim Basin.     

Geochemical Characteristics and Origin of Natural Gases in the Qaidam Basin, China

Sixty-five natural gas samples were collected from 19 oil-gasfields in the Qaidam basin, China. The chemical composition and carbon isotope values of the samples were measured, and the geochemical characteristics and origin of the natural gases were studied. The gases can be divided into biogenic gases, sapropelic oil-type gases, mixed type oil-type gases, coal-type gases and mixed gas. The δ13Ci values of the biogenic gases are very small and the C2+ contents of them are very low, ranging from -68.2‰ to -61.8‰ and 0.06% to 0.20% respectively. They have heavy δD and δ13Cco2> showing a CC>2 reduction pathway. They are distributed in the East depression region and derived from the Quaternary source rocks. The sapropelic oil-type gases have small δ13C2 values and high C2+ ranging from -36.6‰ to -28.6‰ and from 33.01% to 47.15% respectively. The mixed type oil-type gases have <5I3C2 values and C2+ contents varying from -28.6‰ to -24.8‰ and from 4.81% to 26.06% respectively. Both sapropelic oil-typ     

Effects of clay minerals and biosurfactants on isotopic and molecular characteristics of methane encaged in pressure vessel gas hydrates

The stable isotope values of carbon (δ¹³C_methane) and hydrogen (δ²H_methane) from methane molecules trapped in gas hydrates are useful for differentiation of methane from microbial and thermal origins, providing valuable information during hydrocarbon exploration. Recent studies have reported catalysis of methane hydrates when smectite clays and biosurfactants are present in hydrate-hosting sediments, but catalytic influences on the values of δ¹³C_methane and δ²H_methane are not well documented. In this study, pressure vessel methane hydrates were formed from solutions in contact with smectite clays (montmorillonite and nontronite) and biosurfactants (rhamnolipids and surfactin). Experiments show less than 1‰ differences in values of δ¹³C_methane between free and encaged molecules and up to 10‰ variations in values of δ²H_methane between free and encaged molecules. Notably, methane consumption increased in methane hydrates formed from solutions containing biosurfactants and biosurfactant–smectite mixtures. Results presented here indicate that a hydrate formed in the presence of smectite clays and biosurfactants are characterized by small shifts in free and encaged values of δ¹³C_methane and δ²H_methane and do not complicate interpretation of gas origin. In contrast, methane consumption in hydrates formed under the catalytic effect of smectite clays and biosurfactants modifies gas wetness, obscures gas origin and complicates interpretation of thermal maturity.