“BASS 300 PARACOM”: a “model” underwaterparametric communication system

Parametric transduction offers valuable advantages for underwater acoustic communications. Perhaps the most significant benefit is the fact that high directivity is achieved by means of a physically small transmit transducer. This feature may, ultimately, be employed to permit long-range, low-frequency communication using a compact source. The high directivity is desirable to combat multipath propagation and to achieve data communications in water which is shallow by comparison with range. A real-time, high data-rate “model” differential phase shift keying (DPSK) communication system has been constructed and demonstrated. This system uses parametric transduction, with a 300-kHz primary frequency and a 50-kHz secondary frequency. Experimental results show that the system can be employed to combat multipath propagation in shallow water and can achieve high data-rate text and color image transmission at 10 and 20 kb s^-1 for 2-DPSK and 4-DPSK, respectively, through a transmission bandwidth of 10 kHz. The “model” system was developed to confirm performance predictions for a future, operational long-range link employing a 50-kHz primary frequency and a 5-kHz secondary frequency     

Consolidation of double‐layered ground with vertical drains

Vertical drains are usually installed in subsoil consisting of several layers. Due to the complex nature of the problem, over the past decades, the consolidation properties of multi‐layered ground with vertical drains have been analysed mainly by numerical methods. An analytical solution for consolidation of double‐layered ground with vertical drains under quasi‐equal strain condition is presented in this paper. The main steps for the computation procedure are listed. The convergence of the series solution is discussed. The comparisons between the results obtained by the present analytical method and the existing numerical solutions are described by figures. The orthogonal relation for the system of double‐layered ground with vertical drains is proven. Finally, some consolidation properties of double‐layered ground with vertical drains are analysed. Copyright © 2001 John Wiley & Sons, Ltd.     

Dust supply from river floodplains: the case of the lower Huang He (Yellow River) recorded in a loess–palaeosol sequence from the Mangshan Plateau

The Mangshan Plateau is located on the south bank of the Huang He (Yellow River) just west of the city of Zhengzhou, well outside the Loess Plateau in central China. Mixing models of the grain‐size data indicate that the loess deposits are mixtures of three loess components. Comparison of the mixing model with existing models established for a series of loess–palaeosol sequences from the Loess Plateau indicates that the Mangshan loess has been supplied from a proximal dust source, the Huang He floodplain, during major dust outbreaks. The high accumulation rates, the composition of the loess components, and especially the high proportions of a sandy loess component support this. Owing to the exceptionally high accumulation rates, the Mangshan grain size, magnetic susceptibility and carbonate records provide a high‐resolution archive of environmental and climate change. Copyright © 2008 John Wiley & Sons, Ltd.     

Three dimensional simulation of fluid flow in X‐ray CT images of porous media

A numerical scheme is developed in order to simulate fluid flow in three dimensional (3‐D) microstructures. The governing equations for steady incompressible flow are solved using the semi‐implicit method for pressure‐linked equations (SIMPLE) finite difference scheme within a non‐staggered grid system that represents the 3‐D microstructure. This system allows solving the governing equations using only one computational cell. The numerical scheme is verified through simulating fluid flow in idealized 3‐D microstructures with known closed form solutions for permeability. The numerical factors affecting the solution in terms of convergence and accuracy are also discussed. These factors include the resolution of the analysed microstructure and the truncation criterion. Fluid flow in 2‐D X‐ray computed tomography (CT) images of real porous media microstructure is also simulated using this numerical model. These real microstructures include field cores of asphalt mixes, laboratory linear kneading compactor (LKC) specimens, and laboratory Superpave gyratory compactor (SGC) specimens. The numerical results for the permeability of the real microstructures are compared with the results from closed form solutions. Copyright © 2004 John Wiley & Sons, Ltd.     

Relict mountain slope deposits of northern Portugal: facies,sedimentogenesis and environmental implications

This paper deals with the formation processes and the palaeoenvironmental significance of relict slope deposits located on the uppermost part of the north Portugal mountains. For this purpose, seven key sites representative of the different lithofacies have been selected and analysed in detail. The data show that three main dynamic processes are responsible for the emplacement of regional fossil slope deposits: runoff, debris flows and dry grain flows. The ubiquity of these processes and the lack of frost‐related features or landforms do not support the existence of severe Pleistocene climates in this part of the lberian Peninsula as postulated by previous work. Pedological data gathered at one of the study sites show that a subalpine environment was probably present at 700–800 m altitude between 29 and 14 kyr. Using data from the Pyrenees Mountains, a 6.5 to 12°C depression in mean annual temperature has been tentatively postulated for this Pleniglacial period. Copyright © 2003 John Wiley & Sons, Ltd.     

Effect of spatial variation characteristics on contouring of design storm depth

The ordinary kriging method, a geostatistical interpolation technique, was applied for developing contour maps of design storm depth in northern Taiwan using intensity–duration–frequency (IDF) data. Results of variogram modelling on design storm depths indicate that the design storms can be categorized into two distinct storm types: (i) storms of short duration and high spatial variation and (ii) storms of long duration and less spatial variation. For storms of the first category, the influence range of rainfall depth decreases when the recurrence interval increases, owing to the increasing degree of their spatial independence. However, for storms of the second category, the influence range of rainfall depth does not change significantly and has an average of approximately 72 km. For very extreme events, such as events of short duration and long recurrence interval, we do not recommend usage of the established design storm contours, because most of the interstation distances exceed the influence ranges. Our study concludes that the influence range of the design storm depth is dependent on the design duration and recurrence interval and is a key factor in developing design storm contours. Copyright © 2003 John Wiley & Sons, Ltd.     

Elastic solutions for stresses in a transversely isotropic half‐space subjected to three‐dimensional buried parabolic rectangular loads

In many areas of engineering practice, applied loads are not uniformly distributed but often concentrated towards the centre of a foundation. Thus, loads are more realistically depicted as distributed as linearly varying or as parabola of revolution. Solutions for stresses in a transversely isotropic half‐space caused by concave and convex parabolic loads that act on a rectangle have not been derived. This work proposes analytical solutions for stresses in a transversely isotropic half‐space, induced by three‐dimensional, buried, linearly varying/uniform/parabolic rectangular loads. Load types include an upwardly and a downwardly linearly varying load, a uniform load, a concave and a convex parabolic load, all distributed over a rectangular area. These solutions are obtained by integrating the point load solutions in a Cartesian co‐ordinate system for a transversely isotropic half‐space. The buried depth, the dimensions of the loaded area, the type and degree of material anisotropy and the loading type for transversely isotropic half‐spaces influence the proposed solutions. An illustrative example is presented to elucidate the effect of the dimensions of the loaded area, the type and degree of rock anisotropy, and the type of loading on the vertical stress in the isotropic/transversely isotropic rocks subjected to a linearly varying/uniform/parabolic rectangular load. Copyright © 2002 John Wiley & Sons, Ltd.     

The influence of a non‐associated flow rule on the calculation of the factor of safety of soil slopes

This paper presents a method that incorporates a non‐associated flow rule into the limit analysis to investigate the influence of the dilatancy angle on the factor of safety for the slope stability analysis. The proposed method retain's the advantage of the upper bound method, which is simple and has no stress involvement in the calculation of the energy dissipation and the factor of safety. Copyright © 2001 John Wiley & Sons, Ltd.     

Abundance and isotopic composition of noble gases in metal and graphite of the Bohumilitz IAB iron meteorite

Abstract— Abundances and isotopic compositions of noble gases in metal and graphite of the Bohumilitz IAB iron meteorite were measured. The abundance ratios of spallogenic components in metal reveal a ³He deficiency which is due to the diffusive loss of parent isotopes, that is, tritium (Tilles, 1963; Schultz, 1967). The diffusive loss likely has been induced by thermal heating by the Sun during cosmic‐ray exposure (～160 Ma; Lavielle et al, 1999). Thermal process such as impact‐induced partial loss may have affected the isotopic composition of spallogenic Ne. The ¹²⁹Xe/¹³¹Xe ratio of cosmogenic components in the metal indicates an enhanced production of epi‐thermal neutrons. The abundance ratios of spallogenic components in the graphite reveal that it contained small amounts of metal and silicates. The isotopic composition of heavy noble gases in graphite itself was obtained from graphite treated with HF/HCl. The isotopic composition of the etched graphite shows that it contains two types of primordial Xe (i.e., Q‐Xe and El Taco Xe). The isotopic heterogeneity preserved in the Bohumilitz graphite indicates that the Bohumilitz graphite did not experience any high‐temperature event and, consequently, must have been emplaced into the metal at subsolidus temperatures. This situation is incompatible with an igneous model as well as the impact melting models for the IAB‐IIICD iron meteorites as proposed by Choi et al. (1995) and Wasson et al (1980).     

Depositional and post‐depositional history of warm stage deposits at Knocknacran,Co. Monaghan,Ireland: implications for preservation of Irish last interglacial deposits

Organic‐rich deposits, uncovered during overburden removal from mantled gypsum karst at Knocknacran opencast gypsum mine, Co. Monaghan, are the best candidate to date for a last interglacial record in Ireland. The two till and organic‐rich deposits (preserved at different quarry elevations) were emplaced on to a Tertiary dolerite surface during high‐energy flood events and subsequently folded and faulted by movement towards sinkholes in underlying gypsum. Uranium–thorium disequilibrium dating suggests that the organic‐rich deposits in the upper section were hydrologically isolated at ca. 41 ka and those in the lower section at ca. 86 ka. Interpretation of the pollen content, although tentative because of the depositional and post‐depositional history of the material, suggests that the organic material originated in a warm stage possibly warmer than the post‐Eemian interstadials. The unusual setting of preservation may indicate that in situ, last interglacial deposits have generally been removed by erosion in Ireland. Copyright © 2004 John Wiley & Sons, Ltd.