Simultaneous operation of the Sea Beam multibeam echo-sounder andthe SeaMARC II bathymetric sidescan sonar system

An experiment aboard the Scripps Institution of Oceanography's RV Thomas Washington has demonstrated the seafloor mapping advantages to be derived from combining the high-resolution bathymetry of a multibeam echo-sounder with the sidescan acoustic imaging plus wide-swath bathymetry of a shallow-towed bathymetric sidescan sonar. To a void acoustic interference between the ship's 12-kHz Sea Beam multibeam echo-sounder and the 11-12-kHz SeaMARC II bathymetric sidescan sonar system during simultaneous operations, Sea Beam transmit cycles were scheduled around SeaMARC II timing events with a sound source synchronization unit originally developed for concurrent single-channel seismic, Sea Beam, and 3.5-kHz profile operations. The scheduling algorithm implemented for Sea Beam plus SeaMARC II operations is discussed, and the initial results showing their combined seafloor mapping capabilities are presented     

Deep-ocean vertical noise directionality

The structure of beam noise measured at the output of a vertical array in a range dependent ocean basin was investigated using the modified wide-angle parabolic equation (PE). Noise sources were distributed throughout the basin, and the field due to each noise source at an array located in the midbasin was calculated. The response of the array to the superposition of the noise sources was found by beamforming. An efficient and direct approach that superimposes the noise sources on the PE field as the field is marched toward the array was developed. Downslope calculations of the midbasin vertical directionality were made between 50 and 400 Hz with this technique. Use of a geoacoustic model shows that the bottom behaves as a low-pass filter     

Inverted echo sounder measurement of dynamic height through an ENSOcycle in the central equatorial Pacific

A four-year record from an inverted echo sounder deployed near Palmyra Island at 6°N in the central Pacific Ocean is compared with a simultaneous record of subsurface pressure from this island lagoon. A factor m, converting round-trip acoustic travel time to surface dynamic height relative to a deep pressure level, was estimated from the ratio of the spectra of the two records in the energetic synoptic oscillation band. Year-to-year variation in m was not statistically significant. For the overall record, m was found to be -70±8 dynamic m/s, where the error bounds represent a 90% confidence interval. This is consistent with first-baroclinic-mode excitation     

Magma homogenization during anatexis,ascent and/or emplacement? Constraints from the Variscan Weinsberg Granites

Recent studies have shown that melts and residues may not equilibrate during anatexis, and uncertainty exists about the scale on which magmas can be homogenized. This study of elemental and isotopic homogeneity of the South Bohemian Weinsberg granites (˜ 5000 km²) identifies three voluminous, relatively homogeneous magma batches. Each batch has different ⁸⁷Sr/⁸⁶Sr_init (0.7080, 0.7093 and 0.7106), but all equilibrated at ˜ 327–329 Ma, very similar to the time of monazite crystallization. The data cannot entirely prove melt/residue equilibration during anatexis. However, elemental and isotopic compositions imply magma generation by partial melting of heterogeneous South Bohemian crust and chemical differentiation subsequent to Sr-isotope equilibration. Assuming relatively rapid ascent and solidification rates, magma homogenization must have occurred mostly just after partial melting, during melt segregation and accumulation in the deeper crust with slow prograde heating. Models of rapid crustal heating and instantaneous melt extraction are incompatible with the data.     

Wooden Panel Deterioration by Tropical Marine Wood Borers

Wood destruction in test panels ofShorea leprosulawas related to the percentage of fouling, types of wood borers and the number of wood borers. The natural durability ofShorea leprosulapanels was estimated to be 4–5 months in Malaysian marine waters. A higher fouling cover resulted in lower rates of wooden panel deterioration. Larger numbers of wood borers brought about greater panel deterioration. Primary wood destruction was caused by bivalve wood borers, mainlyMartesia striata, Lyrodus pedicellatus, Bankia campanellata, Teredo furciferaandTeredo bartschi. Martesia striatawas the important wood destroying agent in the intertidal zone and, together with the shipworms, was also responsible for panel destruction in the subtidal zone.     

A stepwise method for determining the number of component distributions in a mixture

This paper considers the problem of estimatingm, the number of components in a finite mixture of distributions from a parametric family. A step-up procedure using the bootstrap method is proposed. Some properties of the procedure are illustrated with simulation studies. An example of the method, applied to orientation of beach clasts, is given.     

Effect of element size on the static finite element analysis of steep slopes

The accuracy of the computed stress distribution near the free surface of vertical slopes was evaluated in this study as a function of the element size, including aspect ratio. To accomplish this objective, a parametric study was carried out comparing stresses computed using the finite element method (FEM) to those obtained from a physical model composed of photoelastic material. The results of the study indicate a reasonable agreement between a gelatin model and the FEM model for shear stresses, and an overall good agreement between the two models for the principal stresses. For stresses along the top of the slope, the height of the element tends to be more important than width or aspect ratio, at least for aspect ratios up to 4. In all cases, the greatest difference between the two models occurs in the vicinity of the slope. Specifically, if H is defined as the slope height, an element height of H/10 appears to be adequate for the study of stresses deep within the slope, such as for typical embankment analyses. However, for cases where tensile stresses in the vicinity of the slope face which are critical, such as for the stability analysis of steep slopes, element heights as small as H/32, or higher‐order elements, are necessary. Copyright © 2001 John Wiley & Sons, Ltd.     

Three-dimensional linear solution for wave propagation with slopingbottom

This paper presents a three-dimensional analytic linear wave solution for surface gravity wave propagation over a sloping bottom that is valid for small, but realistic, slopes. The sloping-bottom linear model is compared to published laboratory data and to predictions of two-dimensional, constant-bottom nonlinear theories. The model is shown to describe the measured wave-height growth in the wave transformation region up to a limiting local Ursell number U_r of 0.35-1.0, depending on the wave type, although, as a linear model, it does not predict the harmonics observed in that range. For U_r<0.35, the harmonics can generally be neglected and the sloping-bottom linear theory agrees closely with both the published wave-height data and third-order Stokes nonlinear theory. As a three-dimensional linear model, superposition can be invoked to synthesize and relate wave structure in the transformation region to complex incident ocean spectra with both wind wave and swell components that arrive with a range of incidence angles. As such, the sloping-bottom linear model presented here should be a convenient useful tool for ocean modeling through a significant portion of the wave transformation region     

A time series analysis of sound propagation in a strongly multipathshallow water environment with an adiabatic normal mode approach

Measured time series were generated by small omnidirectional explosive sources in a shallow water area. A bottom-mounted hydrophone recorded sound signals that propagated over a sloping bottom. The time series in the 250-500 Hz band were analyzed with a broad-band adiabatic normal mode approach. The measured waveforms contain numerous bottom interacting multipaths that are complicated by the subbottom structure that contains high-velocity layers near the water-sediment interface. Several of the details of the geoacoustic structure and the depth of the water column at the receiver are inferred from comparisons of the measured data to simulated time series. The sensitivity of broad-band matched-field ambiguity surfaces in the range-depth plane for a single receiver to selected waveguide parameters is examined. A consistent analysis is made where the simulated time series are compared to the measured time series along with the single-receiver matched-field localization solutions for ranges out to 5 km. In this range interval, it was found that the peak cross-correlation between the measured and simulated time series varied between 0.84 and 0.69. The difference between the GPS range and the range obtained from the matched-field solution varied from 0 to 63 m. The geoacoustic structure obtained in the analysis consists of an 8-m low-velocity sediment layer over an 8-m high-velocity layer followed by a higher velocity, infinite half-space     

Evolution of 2:1 layered silicates in low-grade metamorphosed Liassic shales of Central Switzerland

White mica from the Liassic black shales and slates in Central Switzerland was analysed by transmission electron microscopy (TEM) and electron microprobe to determine its textural and compositional evolution during very low-grade prograde metamorphism. Samples were studied from the diagenetic zone, anchizone and epizone (T ≈100°–450 °C). Phyllosilicate minerals analysed include illite/smectite (I/S), phengite, muscovite, brammallite, paragonite, margarite and glauconite. Textural evolution primarily is towards larger, more defect-free grains with compositions that approach those of their respective end-members. The smectite-to-illite transformation reduced the amounts of the exchange components SiK_?1Al_?1, MgSiAl_?2, and Fe³⁺Al_?1. These trends continue to a lesser degree in the anchizone and epizone. Correlations between the proportion of smectite in I/S and the composition of I/S indicate that smectite layers may contain a high layer charge. Illite in I/S bears a compositional resemblance to macrocrystalline phengite in some samples, but is different in others. Paragonite first appears in the upper diagenetic zone or lower anchizone as an interlayer-deficient brammallite, and it may be mixed with muscovite on the nanometre scale. Owing to the small calculated structure factor for paragonite-muscovite superstructures, conventional X-ray powder diffraction cannot distinguish between mixed-layer structures and a homogeneous compositionally intermediate solid solutions. However, indirect TEM evidence shows that irregularly shaped domains of Na- and K-rich mica exist below 10 nm. Subsequent coarsening of domains at higher grades produced discrete paragonite grains at the margins of muscovite crystals or in laths parallel to the basal plane of the host muscovite. Margarite appears in the epizone and follows a textural evolution similar to paragonite in that mixtures of margarite, paragonite, and muscovite may initially occur on the nanometre scale. However, no evidence of interlayer-poor margarite has been found.