大型矩形渡槽-水耦合体系的动力性能分析

本文把任意拉格朗日-欧拉(ALE)方法用于分析大型矩形渡槽结构-水耦合体动力性能,并针对不同的水位、不同截面深宽比,研究渡槽结构在谐波激励、地震激励下的振动反应。研究表明,渡槽结构中水体的泼溅具有明显的非线性特征;渡槽中水位对耦合体动力特性影响极具规律性,但是随截面深宽比减小,水体振荡的非线性明显增强;渡槽结构截面深宽比选择合理,水体泼溅作用产生的倾覆力矩不会使槽体发生倾覆失稳,但是水体的大幅晃动产生的动水压力对渡槽槽身应力有显著的影响,在渡槽抗震设计中应给予足够重视。     

槽墩高度对渡槽结构水平地震响应的影响

为了研究槽墩高度对矩形渡槽结构系统的动力特性及水平地震动力响应的影响,本文采用Housner流-固耦合模型,提出了一种用于土-桩-渡槽-水体系统的有限元分析方法.以渡槽结构原理性拟动力试验结果为依据,对拟动力试验进行了有限元仿真计算,验证了本文所给出的计算模型的合理性.在此基础上,重点对不同槽墩高度的矩形渡槽结构系统进行了计算研究,结果表明:渡槽结构的基频随槽墩高变化显著,而其高阶模态频率则变化不大.在E1 Centro波及TAR波输入时,随着槽墩高的增大,渡槽结构关键部位的最大动应力等响应存在递减趋势;尤其在E1 Centro波输入时,递减趋势更为显著.人工波输入时,结构动力响应状况存在一定波动,但从总体而言志,矮墩渡槽的动力响应大于高墩渡槽的动力响应.     

位移谐波激励下拱顶锚固储罐的动力响应分析

地震中拱顶锚固储罐的破坏将造成严重的后果,研究其地震作用下的动力响应特性具有一定工程意义。以位移简谐波为水平激励,运用AD INA有限元软件对一座3 000m3的拱顶锚固储罐模型进行动力数值模拟,系统分析了储罐内液面晃动波高、动水压力极值、罐壁应力、拱顶应力、拱顶位移等动力响应结果,将以位移谐波激励和以加速度谐波激励的储罐动力响应结果进行比较。分析表明,位移谐波激励下拱顶锚固储罐的液面晃动波高受场地影响较大;储罐应力分布具有一定规律性;采用位移谐波激励时其应力、位移和动水压力等较采用加速度谐波激励时大,液体晃动波高较小。     

地震下方形大断面渡槽水体晃动效应对比分析

随着我国经济的发展,大型渡槽的建设向西部高烈度山区快速推进,渡槽面临着严峻的地震风险。正确模拟渡槽中水体晃动性能,是渡槽抗震性能分析的关键技术难点。依托滇中引水工程中的松林渡槽,本文建立了大断面渡槽结构的精细化有限元模型,通过欧拉-拉格朗日耦合(coupled Eulerian-Lagrangian,简称“CEL”)分析建立了渡槽水体晃动的流固耦合分析模型,同时建立了经典的等效弹簧-质量模型(简称“SM模型”)作为对比,量化两种水体建模方法产生的结果差异。通过对松林渡槽中典型简支跨进行非线性动力时程分析,对比了两种建模方式下,槽身和墩柱混凝土损伤的发展情况,摩擦摆支座的竖向反力,并呈现了CEL分析得到的水体波动情况,阐释了两种分析方法的主要误差来源。在渡槽地震响应分析的基础上,论文建立了槽身的节段模型,研究了CEL方法和等效SM模型在不同槽身加速度和竖向分量下的动力分析结果异同,并提出了等效SM模型的适用范围。     

粉煤灰改良饱和黄土的抗液化特性

为了经济、环保地达到改良处理减轻饱和黄土地基液化震害的目的,通过配备不同粉煤灰掺量的改良黄土进行动三轴试验,研究饱和粉煤灰改良黄土的动应力、动应变和动孔隙水压力变化特征,分析粉煤灰掺量对饱和改良黄土液化应力比、动残余变形和动孔隙水压力的影响规律,并结合微结构试验结果,探讨饱和粉煤灰改良黄土抗液化的物理化学机制。结果表明:粉煤灰掺量对饱和改良黄土的液化应力比、动应变和动孔隙水压力比均具有较为显著的影响。随着粉煤灰掺量的增加,饱和改良黄土的液化应力比持续增加,且当掺量达到15%后,继续增加粉煤灰掺量时改良黄土的液化应力比增加显著。饱和改良黄土的动应变和动孔隙水压力比均随着粉煤灰掺量的增加而减小;掺量达到25%后,饱和改良黄土不液化。饱和粉煤灰改良黄土的SEM细观结构试验照片中呈现大量的圆球状、粒状粉煤灰颗粒和絮凝状胶结物,表明其抗液化的物理化学机制主要包括粉煤灰的水化作用、胶体生成物和颗粒的填隙作用和粉煤灰对游离水的吸附作用。     

不同应力水平下结构性黏土动力特性试验研究

对天津滨海地区典型结构性软黏土进行了压缩试验和不同固结应力下的循环三轴试验。结果表明:结构性软黏土的静力变形特性以先期固结应力和结构屈服应力为分界点可分为3个阶段;不同固结应力下的动应变-振次关系曲线上存在着一个临界动应力比,且该值随着围压的增大而降低;孔隙水压力的变化以结构屈服应力为转折点呈现出不同的变化规律;当振动频率为2Hz时固结应力的改变对轴向动应变的影响不明显。     

水体质量对大型梁式渡槽横向抗震性能影响研究

通过对流固耦合动力作用简化方法的研究,用等效的弹簧-质量系统来模拟流体与渡槽结构的动力相互作用,并对某渡槽进行了多种地震波作用下的抗震性能分析,得到了大型梁式渡槽结构的自振特性、地震响应。结果表明:槽内大质量水体对渡槽的横向地震响应有较大的影响,若不考虑槽内的水体将低估渡槽的地震反应;但因水体的晃荡作用减小了水体自身的地震反应,若将水体视为刚体附加到槽体上将严重地夸大水的地震惯性力作用。     

地面式钢筋混凝土水池自愈、渗漏试验及地震响应分析

钢筋混凝土水池在供水系统中承担着净水、储水的重要功能,是典型的储液结构。裂缝的出现会加速钢筋锈蚀、降低结构耐久性,且结构设计中裂缝宽度限值很大程度上决定了配筋量。水池在地震作用下易出现裂缝,裂缝可能导致储液渗漏,造成水池服务功能下降甚至丧失,并在一定程度上影响整个系统的功能。震后储液结构的裂缝开展情况及由此导致储液渗漏程度是评判水池地震破坏等级的主要标准。目前,已有研究成果表明,混凝土裂缝在与水接触条件下会发生自愈使原有裂缝宽度减小,水池由于储水为裂缝的自愈提供了必要条件。因此,应考虑承载力、耐久性、服务功能、经济性、裂缝自愈性能及震后维修加固可行性等因素综合确定水池结构设计和地震破坏等级划分标准中的裂缝限值。储液结构在地震作用下存在液固耦合效应且液体会发生晃动,储液的存在改变了结构的动力特性和地震响应。水池结构除受到结构本身惯性力和静水压力外,其底部和侧壁还承受液体在垂直壁面方向上产生的动水压力。水池在抗震设计中需考虑液面晃动和动水压力的影响。现阶段,对钢筋混凝土水池裂缝自愈性能、渗漏特性及水池在地震作用下的液固耦合动力特性和地震响应的研究尚不完善。本文通过钢筋混凝土水池壁板弯曲裂缝和贯通裂缝自愈、渗漏试验研究混凝土裂缝的自愈性能及渗漏特性,采用大型有限元软件ADINA进行圆形水池地震响应分析,研究液固耦合系统的动力特性、储液晃动、动水压力及破坏特征等。论文主要完成了如下工作:(1)设计并完成了钢筋混凝土水池壁板弯曲裂缝和贯通裂缝的自愈及渗漏试验。进行了材料性能试验;对静水环境中弯曲微裂缝、流动水环境中贯通裂缝的自愈性能进行了测试,给出了弯曲微裂缝在静水环境中短期内的自愈合宽度,证实了贯通裂缝在流动水环境中仍会发生自愈合;在裂缝上施加实际水头作用测试了弯曲裂缝和贯通裂缝的渗漏特性,研究了弯曲裂缝宽度、受压区高度及作用水头对液体渗漏的影响,分析了贯通裂缝水的渗漏率与累计时间和水头高度之间的关系。通过试验得到裂缝特性与自愈及渗漏之间的关系,为水池结构设计和地震破坏等级划分提供参考。(2)对地面式圆形水池进行了液固耦合动力特性分析,液固耦合系统包括刚体模态、储液晃动模态和液固耦联振动模态3种形式。研究了储水高度、水池半径、液体表面重力波对液固耦合系统动力特性的影响。此外,对比了圆形水池储液晃动频率的理论和有限元计算结果,验证了模型的可靠性,且推导得到圆形水池储液晃动基本周期计算公式。(3)分析了单向水平地震作用下不同水池半径、不同储水高度圆形水池的液面最大晃动波高,拟合得到了圆形水池单向地震作用下的液面最大晃动波高计算公式。公式可用于储液结构地震作用下的最大晃动波高估计和储液结构最大晃动波高设计。结合储液结构长周期抗震设计反应谱和阻尼比修正系数,提出了储水水池液面最大晃动波高计算方法。(4)研究了单向水平地震作用下,不同水池半径、不同储水高度圆形水池池壁、底板环向和径向位置的动水压力数值及分布情况,并与理论计算结果进行了对比;分析了地震动峰值加速度、储水高度、水池半径对动水压力的影响;确定了对流压力与脉冲压力的叠加方法;拟合得到对流压力、脉冲压力及动水压力计算公式;结合底板环向动水压力分布,综合给出单向水平地震作用下圆形水池动水压力标准值,与较复杂的理论计算方法和仅考虑脉冲压力的规范法相比,计算更简便且与实际相符。此外,还分析了液面和池底动水压力的时程变化。(5)进行了双向水平地震动作用下圆形水池的地震响应分析,提取了液面最大晃动波高和动水压力计算结果;基于单向水平地震动作用下的响应结果,通过合理的组合方式给出了双向水平地震动作用下的液面最大晃动波高和动水压力计算公式,建立了双向水平地震作用下储水水池液面最大晃动波高和动水压力计算方法;并对双向水平地震作用下圆形水池地震破坏特征和易损性进行了分析。     

饱和黄土动态液化和静态液化机理的差异性研究

饱和黄土在不同外荷载作用下其液化机理具有显著差异.为研究饱和黄土动态液化和静态液化机理的差异性,基于室内动三轴试验和静三轴试验,研究岷县永光饱和黄土动态液化后的动应力与轴向动应变关系、动孔隙水压力比与轴向动应变关系,分析其静态液化后的偏应力与轴向应变关系、孔隙水压力比与轴向应变关系,并结合液化前、后的SEM试验结果,研...     

调液阻尼器液体动水压力的模拟

本文采用流体体积函数法（ＶｏｌｕｍｅｏｆＦｌｕｉｄＭｅｔｈｏｄ,简称ＶＯＦ法）直接求解不可压缩的,粘性的,瞬变和具有自由表面流体的Ｎａｉｅｒ－Ｓｔｏｋｅｓ方程（简称Ｎ－Ｓ方程）计算了矩形容器中液体晃动时动水压力,为便于工程应用,在计算结果发析的基础上,提出了模拟动水压力的经验公式。     

Equivalent mechanical models of sloshing fluid in arbitrary‐section aqueducts

This paper reports on a semi‐analytical/numerical method to model sloshing water in an arbitrarily shaped aqueduct. The water motion is assumed to be inviscid, compressible, and linear (small displacement). The transverse sloshing fluid in an aqueduct is equivalently simplified as a fixed rigid mass M₀ and a mass–spring system (M₁, K₁). According to a rule that the actual fluid (computed with finite element model) and its equivalent mechanical model have the same first sloshing frequency and acting effects on the aqueduct, the analytical solutions of the fixed (impulsive) mass M₀, sloshing (convective) massM₁, spring stiffness K₁, and their locations in the aqueduct body are acquired by the least squares (curve fitting) algorithm. Applying this equivalent principle, the equivalent mechanical models are respectively obtained for the sloshing water in rectangular, semicircular, U‐shaped, and trapezoid aqueducts. The equivalent principle and fluid models are validated through comparison investigations involving rectangular and U‐shaped aqueducts. The dynamic properties and seismic responses of the original and equivalent systems are simulated, compared, and discussed for a U‐shaped aqueduct bridge. The main purpose of this paper is to provide a simplified model of sloshing fluid for the seismic/wind‐resistant computation of the support structures of the aqueduct bridge. Copyright © 2011 John Wiley & Sons, Ltd.     

Sloshing analysis of rectangular tanks with a submerged structure by using small-amplitude water wave theory

A new sloshing analysis method for rectangular tank systems with a submerged structure are proposed by using the velocity potential and the linear water wave theory. The velocity potential functions are obtained by decomposing the surface wave into a wall-induced wave, reflected and transmitted waves, and a scattered wave. A simplified method using a response spectrum for zero damping is also proposed. The results of the simplified method are in good agreement with those of the analytical method. The sloshing response of the fluid-structure system is found to be very sensitive to the characteristics of the ground motion and the configuration of the system. Under typical earthquakes, the submerged structure shows a tendency to decrease sloshing amplitude, hydrodynamic pressure, and base shear, while it shows a tendency to increase the overturning moment. For the ground excitation dominated by low-frequency contents, the sloshing response increases significantly and the contribution of the higher sloshing modes increases. Copyright © 1999 John Wiley & Sons, Ltd.     

渡槽中流体非线性晃动的边界元模拟

应用边界元法分析了流体非线性晃动及其对渡槽的作用效应,将所得结果与线性解析结果作了比较．数值计算表明：流体以较大幅度晃动时,线性模型结果与非线性边界元结果有较大偏差,计算有限幅流体晃动反应宜采用非线性模型．     

Dynamic response analysis of tube array in partially filled calandria

An efficient procedure is presented for dynamic response analysis of horizontal tube array in partially filled calandria including hydrodynamic interaction effects. The procedure is general enough to consider the transfer of energy between the fluid-coupled tubes, and effects of moderator sloshing on the magnitude and the distribution of hydrodynamic forces. It has been demonstrated that the conventional added mass approach fails to represent behaviour of the tube array correctly, and it is therefore necessary to consider the flexibility of all the tubes along two directions simultaneously. The procedure presented can simulate the added damping effects due to hydrodynamic interaction. The possible use of a tuned damper tube is suggested for controlling sloshing effects for tube array in a calandria where tube frequencies and sloshing frequencies are closely spaced. The presence of surface damping in the tuned tube further brings down the response, and the suggested procedure can be effectively used to control unwarranted sloshing effects. Copyright © 1999 John Wiley & Sons, Ltd.     

LARGE AMPLITUDE LIQUID SLOSHING IN SEISMICALLY EXCITED TANKS

An innovative method of analysis was developed to simulate the non-linear seismic finite-amplitude liquid sloshing in two-dimensional containers. In view of the irregular and time-varying liquid surface, the method employed a curvilinear mesh system to transform the non-linear sloshing problem from the physical domain with an irregular free-surface boundary into a computational domain in which rectangular grids can be analysed by the finite difference method. Non-linearities associated with both the unknown location of the free surface and the high-order differential terms were considered. The Crank–Nicolson time marching scheme was employed and the resulting finite difference algorithm is unconditionally stable and very lightly damped with respect to the temporal co-ordinate. In order to minimize numerical instability caused by the computational dispersion in spatially discretized surface wave, a second-order dissipation term was added to the system to filter out the spurious high-frequency waves. Sloshing effects and structural response were measured in terms of sloshing amplitude, base shear and overturning moment generated by the hydrodynamic pressure of the liquid exerted on the container walls. Simulation results of liquid sloshing induced by earthquake and harmonic base excitations were compared with those of the linear wave theory and the limitations of the latter in assessing the response of seismically excited liquids were addressed.     

Fluid–structure interaction analysis of 3-D rectangular tanks by a variationally coupled BEM–FEM and comparison with test results

A variationally coupled BEM–FEM is developed which can be used to analyse dynamic response, including free-surface sloshing motion, of 3-D rectangular liquid storage tanks subjected to horizontal ground excitation. The tank structure is modelled by the finite element method and the fluid region by the indirect boundary element method. By minimizing a single Lagrange function defined for the entire system, the governing equation with symmetric coefficient matrices is obtained. To verify the newly developed method, the analysis results are compared with the shaking-table test data of a 3-D rectangular tank model and with the solutions by the direct BEM–FEM. Analytical studies are conducted on the dynamic behaviour of 3-D rectangular tanks using the method developed. In particular, the characteristics of the sloshing response, the effect of the rigidity of adjacent walls on the dynamic response of the tanks and the orthogonal effects are investigated. © 1998 John Wiley & Sons, Ltd.     

Investigation of sloshing damping in baffled rectangular tanks subjected to the dynamic excitation

In this research, an analytical model is developed to estimate the hydrodynamic damping ratio of liquid sloshing for wall bounded baffles using the velocity potential formulation and linear wave theory. Here, an analytical solution approach and experimental investigations are conducted for describing the hydrodynamic damping which is provided by vertical and horizontal baffles in partially filled rectangular liquid tanks. In order to evaluate the accuracy of the analytical solution which is developed in present work, a series of experiments are carried out with a rectangular liquid tank excited by harmonic oscillation. The parametric study is conducted on the damping efficiencies of both vertical and horizontal baffles with various dimensions and locations. According to the results of the present investigations, the hydrodynamic damping is significantly affected by the size and location of baffles. Furthermore, the validity of the developed analytical approach as well as the effectiveness of various baffle configurations are discussed. Finally, a simple approach is proposed for estimating the damping ratios of the baffles during earthquake motions.     

预应力混凝土渡槽抗震性能的试验研究

基于预应力混凝土渡槽的低周反复荷载试验,对其受力过程、破坏形态、滞回曲线、刚度退化、耗能能力等抗震性能进行了研究与分析。试验结果表明：预应力混凝土渡槽的破坏形态为弯剪破坏,滞回曲线在加载的初期阶段表现出一定的捏拢效应,滞回曲线总体呈明显的梭形,且较为丰满,耗能能力强,抗震性能优良;配筋合适的预应力混凝土渡槽在加载初期对裂缝控制具有良好的表现,渡槽整体具有良好的延性;在整个加载过程中,渡槽试件的刚度退化明显,刚度退化主要集中在开裂后至屈服这一阶段。     

A model of tuned liquid damper for suppressing pitching motions of structures

A tuned liquid damper (TLD), which consists of rigid tanks partially filled by liquid, is a type of passive control device relying upon liquid sloshing forces or moments to change the dynamical properties and to dissipate vibrational energy of a structure. An analytical non-linear model is proposed for a TLD using rectangular tanks filled with shallow liquid under pitching vibration, utilizing a shallow water wave theory. The model includes the linear damping of the sloshing liquid, which is an important parameter in the study of a TLD as it affects the efficiency of the TLD. Shaking table experiments were conducted for verification; good agreement between the analytical simulations and the experimental results was observed in a small excitation amplitude range. The simulations of TLD-structure interaction by using the proposed model show that the TLD can efficiently suppress resonant pitching vibration of a structure. It is also found that the effectiveness of a TLD for suppressing the pitching vibration depends not only on the mass of liquid in the TLD but also on the configuration of the liquid as well as upon the position where the TLD is located. If the configuration of the liquid, i.e. the liquid depth and the TLD tank size, is designed suitably, the TLD can have a large suppressing moment and can be very effective even with a small mass of liquid.