基于引文分析法的“点-轴系统”理论研究述评

论文采用引文分析法,对陆大道院士所著《关于“点-轴”空间结构系统的形成机理分析》一文的349篇引文进行分析,从引文数量、引文作者、发文期刊、研究案例地、学科领域、研究主题、引用动机7个方面,探究“点-轴系统”理论的研究现状。结果表明：自2002年以来,“点-轴系统”理论的引文数量整体呈上升趋势,研究主题聚焦于区域经济和旅游发展;研究案例地以省级和市级中观尺度为主,多为单一型研究区,主要集中在西北丝绸之路经济带、东北辽宁经济圈、西南藏滇川渝、东部长三角四大热点区域;引文质量普遍较高,并且具有多学科交叉应用的特点,但批判性思考和创造性提升相对较少。基于此,论文从拓展研究和实践应用2个角度对“点-轴系统”理论未来发展进行了展望,以期为相关研究提供参考。     

GNSS多天线基线网单历元模糊度同步解算法

提出多天线基线网单历元模糊度同步解算法，其具体实现步骤为：1）根据宽巷组合模糊度易于固定的优点，采用附加已知基线长度约束法同步解算各基线的宽巷模糊度，得到dm~cm级精度的近似基线分量；2）将解算得到的各近似基线分量作为约束，同步解算各基线的基频模糊度，以获取mm级精度的基线矢量。该方法的关键在于检验各历元宽巷模糊度解算的正确性，以获取可靠的近似基线分量，为解算各基线的基频模糊度提供准确的基线先验信息。由于动态情况下各历元观测信息比较少，单纯依赖ratio检验不可靠，提出结合基线误差、单位权中误差、基线网模糊度闭合环及ratio值等对多组宽巷模糊度进行检验，避免ratio值设置不当导致模糊度检验中发生纳伪和弃真问题。实测数据结果证明，该处理方法使得模糊度解算的成功率提高1%~2%，可以获取移动平台更丰富的导航信息，提高其服务能力。     

A New Wavelet Method for Identification of Eddies and Assessment of Incidents on Islands of the Eastern Caribbean

Using two dimensional continuous wavelet transforms, a novel method for identification of mesoscale eddies is presented to facilitate extraction of characteristics for area, amplitude, type, and location from maps of sea level anomalies. In comparison with the previously established growing method for eddy identification, it is found that the wavelet method identifies more than twice the number of eddies and is particularly better at resolving small eddies down to the 0.25 degree resolution of the data. Such research into eddy identification and tracking is significant to the assessment of eddies with potential to impact on coastlines of small islands. The method is applied to the identification of eddies on tracks towards islands of the Eastern Caribbean over 23?years. Spatial and temporal variation in rate of occurrence and magnitude is established. For Barbados there is an average of 9 anticyclonic incidents a year with maximum amplitude of typically 0.22?m in the dry seasons and 0.16?m in the wet seasons. Seasonal variation is reversed for the other islands with twice the number of anticyclonic incidents having maximum amplitudes of about 0.20?m annually.     

乌鲁木齐大气混合层厚度和稳定度与大气污染的关系

利用乌鲁木齐市4座10层100 m梯度气象塔2013年6月~2014年4月气象观测资料和7个环境监测站[WTBX]AQI[WTBZ]资料，计算并分析了大气混合层厚度和稳定度特征，探讨了大气混合层厚度和稳定度与污染的关系。结果表明：乌鲁木齐市混合层厚度夏季郊区高、城区低，冬季从南郊—城区—北郊随地势降低依次降低；夏季和冬季分别在1 559～1 772 m和526～1 156 m之间。地面至2 km以上每500 m高度间隔统计混合层厚度，500～1 000 m出现频率最多；月变化为6～9月基本在500 m以上，且每个高度区间其概率均超过10%，10月～次年2月1 500 m以上区间概率明显减小；日变化为中午13:00～16:00达到最高值，下午和傍晚迅速下降。白天较大的感热输送提供充足的热力条件，这也体现出白天以不稳定层结为主，夜间则以稳定层结为主。大气稳定度分类结果，夏季郊区和城区不稳定（A～C类）所占比例差不多，冬季北郊稳定（E、F类）所占比较最大、城区最弱。[WTBX]AQI指数冬季最大，从南郊—城区—北郊依次增大，这与采暖期污染物多、南郊比北郊地势高有利于扩散输送有关。总体来看，乌鲁木齐大气混合层厚度空间分布与气象要素、大气稳定度、地形等密切相关，对AQI[WTBZ]指数分布有重要影响，这对近地层大气污染状况预报有着重要的指导意义。     

徐闻南山镇红树林沉积物及红树植物中重金属的累积特征与迁移规律

为探究重金属在红树林沉积物及红树植物中的分布累积及迁移规律，选取了徐闻南山镇红树林为研究对象，通过测定红树林沉积物及红树植物不同部位（根、茎、叶）的重金属质量分数，运用富集因子、生物富集系数、转移系数及相关性分析等方法进行分析。结果表明：1）红树林沉积物重金属质量分数表现为铬（Cr）＞锌（Zn）＞镍（Ni）＞铜（Cu）＞铅（Pb）＞砷（As）＞汞（Hg）＞镉（Cd），为中等变异程度；除了镍（Ni）元素外，其余7种重金属未超过国家一级标准，除了铅（Pb）元素外，其余7种重金属均超过广东省土壤环境背景值，说明研究区沉积物中重金属具有一定的积累效应。2）沉积物中砷（As）、铜（Cu）、锌（Zn）、汞（Hg）、镍（Ni）、铬（Cr）富集因子值均＞1.5，说明受到轻微人为活动影响；各站位镍（Ni）富集因子值均＞5，结合研究区背景，反映了镍（Ni）受到自然和人为输入的共同影响。3）白骨壤体内重金属主要集中在根部，而红海榄体内重金属在根茎叶中分布相对均匀。白骨壤根茎叶部位的大多数重金属质量分数远高于红海榄，说明白骨壤对重金属的吸附能力比红海榄强。汞（Hg）集中分布在植物的叶片部位，且与其他重金属之间相关性不明显；推测汞（Hg）主要通过叶片吸收进入植物体内，与交通运输污染有关。4）不同红树植物对不同重金属富集能力各异，白骨壤对重金属的富集能力表现为：镉（Cd）＞砷（As）＞铜（Cu）＞锌（Zn）＞汞（Hg）＞铅（Pb）＞镍（Ni）＞铬（Cr），红海榄表现为：镉（Cd）＞铜（Cu）＞汞（Hg）＞锌（Zn）＞铅（Pb）＞砷（As）＞镍（Ni）＞铬（Cr）。白骨壤和红海榄对汞（Hg）的运移能力都较强；红海榄对镉（Cd）的富集能力和转运能力都较强，而白骨壤对镉（Cd）富集能力较强，转运能力却较弱，这说明红树植物对重金属元素的富集能力与转运能力不存在正比关系。     

高精度直升机机载LiDAR在高速公路改扩建勘测中的应用可行性研究

机载LiDAR在公路勘测方面的用途日益广泛。该文对直升机机载LiDAR在高速公路改扩建中的应用技术路线可行性进行了研究论证,从地面控制测量、点云数据获取、点云数据处理、成果应用等多个方面进行了阐述,通过分析LiDAR点云数据在5种不同地面控制点布设方案校正下的点云数据精度,论证了利用地面控制点对直升机机载LiDAR点云数据进行平面和高程校正的可行性。     

广盐性鱼类渗透压适应性与生理可塑性机制研究

拥有强大的渗透压调节能力对广盐性鱼类的生存至关重要。目前,关于鱼类渗透压调节机制已有不少研究,但均存在较大的局限性。本文从广盐性鱼类渗透压信号转导机制、渗透胁迫的细胞调控机制、渗透调控的内分泌调节机制和无机离子通道和转运蛋白介导的渗透调控等方面对广盐性鱼类的渗透压适应性和生理可塑性机制进行分析,以期从分子、细胞、通路和生理等层次初步探索广盐性鱼类盐度胁迫后的可塑性表型变化和不同盐度条件下的应答机制,为广盐性鱼类的渗透压调节机制的深入研究奠定基础。对广盐性鱼类渗透压适应性与生理可塑性机制研究,有助于研究其环境适应机理,促进野生鱼种的人工化养殖以及新品种的育种从而提高经济效益、社会效益和生态效益,对促进水产养殖学进步以及养殖业的发展具有重要意义,同时,为研究广盐性鱼类的渗透压调节机制开辟新的研究方向。     

Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.     

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.     

鄂尔多斯地块周缘垂直形变场负位错反演与应变积累研究

利用鄂尔多斯地块及其周缘1970～2014年的垂直形变速率场资料，借助负位错反演研究该区域长期应变积累。结果表明，地块东北缘山西断陷带中北段年均能量积累增量、剪应力强度都较高，西南缘六盘山断裂与渭河断裂西段次之；山西断陷带中南段至晋陕交界处年均剪应力强度较高且显示一定程度的能量积累；西秦岭构造区尤其西秦岭北缘断裂西段、晋冀蒙交界区也反映一定程度的能量积累特性。