Experimental study on the deterioration and natural remediation of the Ariake Sea tidal mud caused by the sea laver treatment acid practice and the upward seepage of pore water liquid

This study presents a laboratory study of the following two aspects: (1) the influence of sea laver treatment acid on the geoenvironmental properties of Ariake Sea tidal mud, and (2) the natural remediation effect on the sea laver treatment acid contaminated Ariake Sea tidal mud caused by the upward seepage of pore water liquid in the mud. Firstly, the mechanisms of the transport of sea laver treatment acid in the Ariake Sea tidal mud and the generation mechanisms of the upward seepage flow in the Ariake Sea tidal mud are discussed. Secondly, a series of one-dimensional laboratory infiltration tests were carried out to investigate the deterioration of the Ariake Sea tidal mud caused by the sea laver acid treatment practice. Test results reveal that the acid treatment practice caused considerable change in the geochemical properties of the mud in terms of increase in sulfide content and decrease in pH value. After the treatment by the sea laver treatment acid, the sulfide content of the mud even exceeded the safe limit value for the benthos, which represents undesirable living condition for benthos. Thirdly, series of laboratory fresh seawater infiltration tests for the deteriorated Iida site mud were conducted to illustrate this natural remediation efficiency. It is found that with the infiltration of the fresh seawater, the sulfide content of the Iida site mud was considerably reduced and pH value increased to an acceptable range for benthos living in the tidal flat mud. With the increase in the infiltration time and the hydraulic gradient, the remediation efficiency could be increased.     

Determination of Sr/Sr mass-dependent isotopic fractionation and radiogenic isotope variation of Sr/Sr in the Neoproterozoic Doushantuo Formation

We measured both mass-dependent isotope fractionation of δ⁸⁸Sr (⁸⁸Sr/⁸⁶Sr) and radiogenic isotopic variation of Sr (⁸⁷Sr/⁸⁶Sr) for the Neoproterozoic Doushantuo Formation that deposited as a cap carbonate immediately above the Marinoan-related Nantuo Tillite. The δ⁸⁸Sr and ⁸⁷Sr/⁸⁶Sr compositions showed three remarkable characteristics: (1) high radiogenic ⁸⁷Sr/⁸⁶Sr values and gradual decrease in the ⁸⁷Sr/⁸⁶Sr ratios, (2) anomalously low δ⁸⁸Sr values at the lower part cap carbonate, and (3) a clear correlation between ⁸⁷Sr/⁸⁶Sr and δ⁸⁸Sr values. These isotopic signatures can be explained by assuming an extreme greenhouse condition after the Marinoan glaciation. Surface seawater, mixed with a large amount of freshwater from continental crusts with high ⁸⁷Sr/⁸⁶Sr and lighter δ⁸⁸Sr ratios, was formed during the extreme global warming after the glacial event. High atmospheric CO₂ content caused sudden precipitation of cap carbonate from the surface seawater with high ⁸⁷Sr/⁸⁶Sr and lighter δ⁸⁸Sr ratios. Subsequently, the mixing of the underlying seawater, with unradiogenic Sr isotope compositions and normal δ⁸⁸Sr ratios, probably caused gradual decrease of the ⁸⁷Sr/⁸⁶Sr ratios of the seawater and deposition of carbonate with normal δ⁸⁸Sr ratios. The combination of ⁸⁷Sr/⁸⁶Sr and δ⁸⁸Sr isotope systematics gives us new insights on the surface evolution after the Snowball Earth.     

Towards a direct collapse–load method of design for concrete frames subjected to severe ground motions

Most current methods of design for concrete structures under earthquake loads rely on highly idealized ‘equivalent’ static representations of the seismic loads and linear‐elastic methods of structural analysis. With the continuing development of non‐linear methods of dynamic analysis for the overload behaviour and collapse of complete concrete structures, a more direct and more accurate design procedure becomes possible which considers conditions at system collapse. This paper describes an evaluation procedure that uses non‐linear dynamic collapse–load analysis together with global safety coefficients. A back‐calibration procedure for evaluating the global safety coefficients is also described. The aim of this paper is to open up discussion of alternative methods of design with improved accuracy which are necessary to move towards a direct collapse–load method of design. Copyright © 2002 John Wiley & Sons, Ltd.     

Paleogeographic maps of the Japanese Islands: Plate tectonic synthesis from 750 Ma to the present

Abstract A series of paleogeographic maps of the Japanese Islands, from their birth at ca 750–700 Ma to the present, is newly compiled from the viewpoint of plate tectonics. This series consists of 20 maps that cover all of the major events in the geotectonic evolution of Japan. These include the birth of Japan at the rifted continental margin of the Yangtze craton ( ca 750-700 Ma), the tectonic inversion of the continental margin from passive to active ( ca 500 Ma), the Paleozoic accretionary growth incorporating fragments from seamounts and oceanic plateaux ( ca 480-250 Ma), the collision between Sino-Korea and Yangtze (250–210 Ma), the Mesozoic to Cenozoic accretionary growth (210 Ma-present) including the formation of the Cretaceous paired metamorphic belts (90 Ma), and the Miocene back-arc opening of the Japan Sea that separated Japan as an island arc (25-15 Ma).     

Experimental and theoretical study of stability of dense hydrous magnesium silicates in the deep upper mantle

Fluid-undersaturated experiments were conducted to determine the phase relations in the simplified peridotite system MgO-SiO₂-H₂O (MSH) at 11.0-14.5 GPa and 800-1400 °C. Stability relations of dense hydrous magnesium silicates (DHMSs) under fluid-undersaturated conditions were experimentally examined. From the fluid-absent experimental results, we retrieved thermodynamic data for clinohumite, phase A, phase E, and hydrous wadsleyite, consistent with the published data set for dry mantle minerals. With this new data set, we have calculated phase equilibria in the MSH system including dehydration reactions. The dehydration reactions calculated with lower water activities of 0.68-0.60 match the fluid-present experiments of this study above 11.0 GPa and 1000 °C, indicating that considerable amounts of silicate component were dissolved into the fluid phase. The calculated phase equilibria illustrate the stability of the post-antigorite phase A-bearing assemblages. In the cold subducting slab peridotite, phase A + enstatite assemblage survives into the transition zone, whereas phase A + forsterite + enstatite assemblage forms hydrous wadsleyite at a much shallower depth of about 360-km. The slab is subducted with no dehydration reactions occurring when entering the transition zone. The phase equilibria also show the high temperature stability of phase E. Phase E is stable up to 1200 °C at 13.5 GPa, a plausible condition in the mantle of relatively low temperature, i.e., beneath subduction zones. Phase E is a possible water reservoir in the mantle as well as wadsleyite and ringwoodite.     

High-reliability zircon separation for hunting the oldest material on Earth: An automatic zircon separator with image-processing/microtweezers-manipulating system and double-step dating

Despite the recent development in radiometric dating of numerous zircons by LA-ICPMS, mineral separation still remains a major obstacle, particularly in the search for the oldest material on Earth. To improve the efficiency in zircon separation by an order of magnitude, we have designed/developed a new machine-an automatic zircon separator(AZS). This is designed particularly for automatic pick-up of100 μm-sized zircon grains out of a heavy mineral fraction after conventional separation procedures. The AZS operates in three modes:(1) image processing to choose targeted individual zircon grains out of all heavy minerals spread on a tray,(2) automatic capturing of the individual zircon grains with microtweezers, and(3) placing them one-by-one in a coordinated alignment on a receiving tray. The automatic capturing was designed/created for continuous mineral selecting without human presence for many hours. This software also enables the registration of each separated zircon grain for dating, by recording digital photo-image, optical(color) indices, and coordinates on a receiving tray. We developed two new approaches for the dating; i.e.(1) direct dating of zircons selected by LA-ICPMS without conventional resin-mounting/polishing,(2) high speed U-Pb dating, combined with conventional sample preparation procedures using the new equipment with multiple-ion counting detectors(LA-MIC-ICPMS).With the first approach, Pb-Pb ages obtained from the surface of a mineral were crosschecked with the interior of the same grain after resin-mounting/polishing. With the second approach, the amount of time required for dating one zircon grain is ca. 20 s, and a sample throughput of 150 grains per hour can be achieved with sufficient precision(ca. 0.5%).We tested the practical efficiency of the AZS, by analyzing an Archean Jack Hills conglomerate in Western Australia with the known oldest(4.3 Ga) zircon on Earth. Preliminary results are positive; we were able to obtain more than 194 zircons that are over 4.0 Ga out of ca. 3800 checked grains, and 9 grains were over 4300 Ma with the oldest at 4371 ± 7 Ma. This separation system by AZS, combined with the new approaches, guarantees much higher yield in the hunt for old zircons.     

Tectonic evolution of the ultrahigh-pressure (UHP) and high-pressure (HP) metamorphic belts from central China

Abstract In the Triassic suture between the Sino-Korean and Yangtze cratons, the Dabie metamorphic Complex in central China includes three tectonic units: the northern Dabie migmatitic terrane, the central ultrahigh-P coesite- and diamond-bearing eclogite belt, and the southern high-P blueschist-eclogite belt. This complex is bounded to the north by a north-dipping normal fault with a Paleozoic accretionary complex and to the south by a north-dipping reverse fault with Yangtze basement plus its foreland fold-and-thrust sequence. Great differences in metamorphic pressure suggests that these units reached different depths during metamorphism and their juxtaposition occurred by wedge extrusion of subducted old continental fragments. These units were subsequently subjected to (i) Barrovian type regional metamorphism and deformation at shallow depths; (ii) intrusion of Cretaceous granitic plutons; and (iii) doming and segmentation into several blocks by normal and strike-slip faults. A new speculative model of tectonic exhumation of UHP rocks is proposed.     

Measurement of small ions and condensation nuclei over the sea near the land

Summary To study the ionization equilibrium, simultancous measurements of the concentration of small ions (n), concentration of condensation nuclei (Z), and the diffusion coefficient of condensation nuclei (D) have been carried out over the sea. If we take the variation ofD into consideration, the correlation among them was found to be well expressed by the simple formula;q=n Z. The dependence of the effective attachment coefficient of small ions () upon the size of nuclei (2r) were also studied, and was found to correlate well withD orr. Slight differences of the dependence of uponD orr over the sea from that over the land seem to be well explained by the difference of charged states of nuclei over the sea and land.

---

Zusammenfassung Zur Untersuchung des Ionisationsgleichgewichts wurden gleichzeitige Messungen der Konzentration schneller Ionen (n), der Konzentration der Kondensationskerne (Z) und des Diffusions-Koeffizienten der Kondensationskerne (D) über dem Meere ausgefürt. Unter Berücksichtigung des Diffusions-Koeffizienten (D) konnte der Zusammenhang zwischen den beiden anderen Grössen recht gut durch eine einfache Formel ausgedrückt werden:q=n Z. Die Abhängigkeit des wirksamen Anlagerungskoeffizienten für schnelle Ionen () von der Grösse der Kondensationskerne (2r) wurde ebenfalls untersucht, und es wurde gefunden, dass recht gut mitD oderr korreliert. Kleinere Unterschiede in der Abhängigkeit von vonD oderr, welche bei einem Vergleich der Messungen über See und über Land festgestellt wurden, liessen sich gut durch den Unterschied der geladenen Zustände der Kondensationskerne über See und Land erklären.

     

On-going orogeny in the outer-arc of the Timor–Tanimbar region, eastern Indonesia

The Timor–Tanimbar islands of eastern Indonesia form a non-volcanic arc in front of a 7 km deep fore-arc basin that separates it from a volcanic inner arc. The Timor–Tanimbar Islands expose one of the youngest high P/T metamorphic belts in the world, providing us with an excellent opportunity to study the inception of orogenic processes, undisturbed by later tectonic events.Structural and petrological studies of the high P/T metamorphic belt show that both deformation and metamorphic grade increase towards the centre of the 1 km thick crystalline belt. Kinematic indicators exhibit top-to-the-north sense of shear along the subhorizontal upper boundaries and top-to-the-south sense in the bottom boundaries of the high P/T metamorphic belt. Overall configuration suggests that the high P/T metamorphic rocks extruded as a thin sheet into a space between overlying ophiolites and underlying continental shelf sediments. Petrological study further illustrates that the central crystalline unit underwent a Barrovian-type overprint of the original high P/T metamorphic assemblages during wedge extrusion, and the metamorphic grade ranged from pumpellyite-actinolite to upper amphibolite facies.Quaternary uplift, marked by elevation of recent reefs, was estimated to be about 1260 m in Timor in the west and decreases toward Tanimbar in the east. In contrast, radiometric ages for the high P/T metamorphic rocks suggest that the exhumation of the high P/T metamorphic belt started in western Timor in Late Miocene time and migrated toward the east. Thus, the tectonic evolution of this region is diachronous and youngs to the east. We conclude that the deep-seated high P/T metamorphic belt extrudes into shallow crustal levels as a first step, followed by doming at a later stage. The so-called ‘mountain building’ process is restricted to the second stage. We attribute this Quaternary rapid uplift to rebound of the subducting Australian continental crust beneath Timor after it achieved positive buoyancy, due to break-off of the oceanic slab fringing the continental crust. In contrast, Tanimbar in the east has not yet been affected by later doming. A wide spectrum of processes, starting from extrusion of the high P/T metamorphic rocks and ending with the later doming due to slab break-off, can be observed in the Timor–Tanimbar region.     

Methane-induced dolomite “chimneys” on the Kuroshima Knoll, Ryukyu islands, Japan

The Kuroshima Knoll is about 26 km south of Ishigaki Island in the southern part of the Ryukyu Arc. The area is considered to be the source area of “The 1771 Yaeyama Earthquake Tsunami”, which was due to the submarine landslide caused by an earthquake. It has been cleared from some investigations using “Dolphin 3K” and “Shinkai 2000” that there are large-scale dead Calyptogena colonies, many gravels of fallen dolomite chimneys and carbonates on the top of the Knoll [Matsumoto, T., Uechi, C., Kimura, M., 1997; Machiyama, H., Matsumoto, T., Matsumoto, R., Hattori, M., Okano, M., Iwase, R., Tomaru, H., 2001b.]. Carbonates of Kuroshima Knoll have various shapes and macroscopic textures. These have been classified into 4 types; shell crust (pavement), chimney, burrow, and nodule. It is clear that all chimney and burrow carbonates are composed of dolomite, while shell curst and nodule are composed of calcite, sometimes both calcite and dolomite. These carbonates are considered to have been formed by cold seep, because they are characterized by the light carbon isotopic ratio (semi-biogenic) and the heavy oxygen isotopic ratio. This suggests that methane hydrate layers develop under this survey area and the water that has the heavy oxygen and the light carbon isotopic ratio is derived from the dissociation of methane hydrate.