斜轴式太赫兹天线的卡焦近场全息测量研究

天线反射面的面形精度直接影响天线效率, 是望远镜的关键指标之一. 近场射电全息具有测量精度高, 便捷高效的优点, 是毫米波和亚毫米波射电望远镜面形检测最为常用的方法之一, 卡焦近场全息可以完整测量望远镜光路中整体的面形误差. 斜轴式机架结构能够更好地适应太赫兹望远镜在极端台址环境下的整体保温和热控需求, 但斜轴天线特殊的转动特性会在近场全息测量过程中引入额外的系统误差. 针对斜轴式天线的卡焦近场全息测量, 分析了数据处理中需要额外考虑的参考路接收机位置和副面衍射的影响, 并在1.2m口径斜轴式太赫兹天线上开展了测量实验. 实验结果表明, 卡焦近场全息测量的重复测量精度优于2.0μm RMS (Root Mean Square), 面形误差分布与摄影测量所得结果一致, 验证了误差分析与修正的正确性.     

40m射电望远镜天线副面和馈源偏移误差分析

建立40m口径天线结构的有限元分析模型,依据有限元分析结果,对副面和馈源偏离理想位置的偏移量和偏移误差进行分析与计算;从误差补偿角度,运用最佳指向技术对副面横偏误差进行补偿分析计算。误差补偿后的计算结果表明,副面横偏误差得到了大幅度的减小。分析计算结果为40m天线的实际工程提供了参考。     

偏焦全息测量技术在上海65米射电望远镜中的应用研究

上海65米射电望远镜是亚洲最大、全方位可转动的大型射电望远镜,在国内首次配备主动面系统。对主动面系统应用的关键技术——偏焦全息测量技术在上海65米射电望远镜中的初步应用情况进行介绍。首先,介绍常用的天线主反射面面型测量方法。接着,介绍偏焦全息测量技术的应用方法。采用飞行扫描,利用X波段致冷接收机和连续谱终端,将射电源3C84作为信号源,通过移动副反射面测量得到一幅聚焦天线方向图和两幅偏焦天线方向图。将三幅天线方向图作为偏焦全息测量算法的输入,获得天线口径面相位分布的Zernike系数。依据Zernike系数计算得到天线主反射面型面误差的均方根值(root mean square,RMS),该均方根值与前期照相测量的结果基本相符。最后,对今后的改进工作进行展望。     

PSD法测量大型射电望远镜副面位姿

指向精度是大型射电望远镜天线具有挑战性的关键技术指标.在望远镜运行中,方位俯仰角的变化、重力以及日照等对副面撑杆的综合影响会引起望远镜的副面位姿改变从而引起指向误差的增加和天线效率的降低.基于天马65 m射电望远镜,使用位置传感器装置(PSD)法构建了副面位置偏移量测定系统,可以实时采集副面的3维位移数据,构建重力模型,将测试结果与射电法构建的现有副面模型进行对比,有较好的一致性.此外,该系统可以分析日照(引起撑腿局部温度效应)引起的副面位移情况,也可以监视风载和瞬时启停对副面位姿的影响.     

TM65 m射电望远镜副面位姿建模

大型射电望远镜在观测过程中,随着俯仰角度的变化,副面支撑、背架、主反射面等都有不同程度的变形,这将导致天线效率在高低俯仰角上明显下降,天马65 m射电望远镜副面系统的安装可以用来补偿副面支撑和主面的重力变形,在不同的俯仰角度上,副面位姿的调整可以提高天线的效率和指向性能.通过在X波段和Ku波段研究副面位姿变化对天线效率的影响,用射电法建立了随俯仰角度变化的副面位姿随动调整模型和指向补偿模型.此外还测试了副面随动与固定对天线效率的影响,结果表明副面随动模型可以有效改善65 m望远镜在高低俯仰角上的效率,使得在整个俯仰角范围内,X波段的接受效率均达到60%以上.     

50米天线馈源焦点偏移补偿控制系统的设计

通过测量北京密云50m天线在不同俯仰角度下X波段馈源的焦点轴向偏移,拟合出了由于天线重力形变引起的X波段馈源的焦点轴向偏移曲线.为了补偿焦点偏移,设计了包含电流环、转速环和位置环的馈源控制系统,并基于Matlab/Simulink软件,对系统进行了仿真.仿真结果表明,本文设计的馈源控制系统能够补偿焦点偏移,且系统具有良好的动态和稳态性能.     

南极5 m太赫兹望远镜指向与调焦校准精度分析

指向校准与副面调焦是天线测量的重要组成部分,对射电望远镜实际的观测性能有重要影响.根据南极5 m太赫兹望远镜(DATE5)指向精度和离焦增益损失的指标要求,计算得到了指向校准与副面调焦观测过程中对信噪比的要求,并以此为依据选取了若干可行的候选校准源,包括太阳系行星和超致密电离氢区.分析了大气吸收和校准源角直径对测量精度的影响.仿真分析结果表明:望远镜在南极工作时,这些校准源在一定的高度角范围内可以提供足够强的流量密度,用来验证预先建立的太赫兹和光学望远镜两光轴指向偏差模型以及副面调焦模型.     

德令哈13.7m望远镜热变形研究

热变形是影响大型毫米波天线性能的关键因素之一.这种变形会改变天线反射面的轴线和焦距、恶化反射面面形,导致天线效率和指向精度恶化,同时也使天线效率和指向的长时间稳定性降低.由于太阳的周日运动,造成望远镜4个主支撑腿(简称支腿)之间存在温差,且该温差是变化的,从而引起方位轴的倾斜周期性变化.采用数字摄影测量、倾斜仪测量及天文实测等多种仪器和方法,研究了德令哈13.7m望远镜天线的热变形规律,并根据实时测量的主面温度分布,实现了副面自适应调焦补偿,使得天线效率提高近1倍.测量发现常规指向模型修正后的残差与天线主反射面(包括反射面板和背架,简称主面)直径方向温差存在线性相关性,故在指向解析模型中加入了温差修正项,并通过采用隔热材料包裹支腿的办法显著减小了支腿之间的温差,从而改善了望远镜的指向精度.     

采用光学指向系统建立天马13m望远镜指向模型

描述了采用光学望远镜辅助天马13m射电望远镜进行指向测量以及建立指向误差修正模型的方法. 对于小口径望远镜, 指向校准目标源比较少, 用射电法建立指向模型难以覆盖全天区. 利用上海天文台天马13m射 电望远镜进行光学望远镜辅助射电望远镜指向测量研究, 在13m天线背架上安装一套光学指向系统, 获得了优 于3''的重复测量误差. 此外, 通过对影响天线指向因素的分析, 建立了包含8个误差项的指向误差修正模型以及 光轴和电轴偏差模型. 将指向模型代入天线伺服控制系统, 对校准目标射电源进行十字扫描, 得到指向样本残差约 为5''. 该研究可以为实现高精度指向建模提供一种参考方法.     

65 m射电望远镜背架结构日照温度效应实验研究

借助精密工程测量手段,对65 m天线背架的日照温度效应进行了实验研究.在天线背架设计坐标系下分析实验数据,建立了日照温度变形模型,得出背架结构沿X方向变形系数为Kx=1.30×10-5,沿Z方向变形系数为Kz=-0.44×10-5,沿Y方向变形偏向太阳照射一侧.根据实验数据建立的背架变形模型,模拟分析了65 m天线背架日照温度变形对面形精度的影响,得出环境温度变化1℃带来的面形精度(均方根值rms)影响分量约为0.09 mm.实验结果为65 m天线主动面调节提供了很有价值的参考数据.     

Phase Analysis of Aperture Surface on Ring Focus Antenna

The ring focus antenna has special electromagnetic characteristics and application fields. The phase error of ring focus antenna is analyzed theoretically and simulatedly. The phase error caused by the position deviation of the feed and the subreflector, the compensation relationship between the main reflector and subreflector, and the optical path difference caused by the operation of the antenna in holographic measurement are derived. The results will provide theoretical basis and reference for accurate surface measurement and compensation of the ring focus antenna.     

A Research on the Gravity Deformation of Delingha 13.7m Telescope

Based on digital photogrammetric measurements, the antenna panels of the Delingha 13.7m radio telescope are adjusted to make the main dish have an optimal paraboloidal surface at the elevation of 52°, thus the overall antenna efficiency is optimized for different observing elevations. Observations indicate that the aperture efficiency of the telescope has been improved approximately twice in comparison with the antenna panels adjusted on the basis of theodolite measurements. According to the results of the measurements at different elevations, the models of antenna gravity deformation are built, including the displacement and tilt angle of the subreflector, as well as the focal length and surface error of the main reflector, as functions of elevation angle. In the process of modeling the gravity deformation of the main dish, instead of the direct calculation method, the least square fitting on the measured surface errors at different elevation angles is adopted, in order to reduce the effect of measurement errors on the accuracy of the model.     

Subreflector model depending on elevation for the Tianma 65m Radio Telescope

A subreflector adjustment system for the Tianma 65 m radio telescope, administered by Shanghai Astronomical Observatory, has been installed to compensate for gravitational deformation of the main reflector and the structure supporting the subreflector. The position and attitude of the subreflector are variable in order to improve the efficiency at different elevations. The subreflector model has the goal of improving the antenna's performance. A new fitting formulation which is different from the traditional formulation is proposed to reduce the fitting error in the Y direction. The only difference in the subreflector models of the 65 m radio telescope is the bias of a constant term in the Z direction. We have investigated the effect of movements of the subreflector on the pointing of the antenna. The results of these performance measurements made by moving the antenna in elevation show that the subreflector model can effectively improve the efficiency of the 65 m radio telescope at each elevation. An antenna efficiency of about 60% at the K u band is reached in the whole angular range of elevation.     

基于应变的变形副反射面位姿形貌快速重构方法

随着双反射面天线口径的增大、工作频段的升高,天线对副反射面的精度要求也越来越高.当天线受到自重以及风荷、温度等外界因素的影响时,为了更好地保证满足天线的高指向精度等电性能要求,基于应变传感器和模态叠加原理,分别利用天线变形后副反射面支撑腿与副反射面自身结构的应变值来快速重构副反射面的位姿、形貌,便于副反射面调整机构对其进行实时修正,以实现更加精准的主副反射面位置匹配,降低因天线结构变形造成的波束指向误差和增益损失.     

Analysis and Correction of the Influence of Track Irregularity on the Antenna Pointing

According to the influence mechanism of the antenna track irregularity on the telescope pointing accuracy, the distribution of the track errors and their influence on the pointing of the Urumqi Nanshan 26 m telescope are reanalyzed after the antenna track was reformed by using the whole-body welding technology, and hereby the pointing error model is correspondingly revised. By using the moving least-squares method, the measured height errors of the antenna track plane are fitted with a closed curve, and the tilt of the antenna azimuth axis caused by the track irregularity can be determined accordingly. Comparing it with the measured deviation of the antenna azimuth axis caused by the deformation of antenna pedestal, it can be found that both deviations are strongly correlated. A new pointing error model is established in view of the gravity deformation of antenna pedestal, which includes the north-south and east-west components, as well as the antenna track irregularity. Finally, by scanning a known calibration radio source at different positions in the sky, the measured pointing errors are fitted with the new pointing error model. The result shows that the sinusoidal component of the model error can be well constrained by the new pointing correction model, indicating that the new model can reflect very well the antenna pointing error, and can amend it to a certain extend.     

Correction Method of Antenna Pointing Error Caused by the Main Reflector Deformation

The pointing accuracy of a radio telescope is usually less than one-tenth of its antenna beam width. For large-aperture antennas at the short-centimeter band or millimeter-wave band, the pointing accuracy must be as high as several arc seconds. Therefore, for large-diameter and high-frequency reflector antennas, the pointing problem has become an important focal point to realize the antenna performance. Among many structural subsystem factors that affect the antenna pointing accuracy, there has been only less study on the factor of main reflector deformation. Based on the structural characteristics of the antenna, a reflector space coordinate system is established in this paper. And based on the space coordinates of the main reflector surface points after deformation, a non-linear least squares fitting method with 3 degrees of freedom is proposed to accurately predict the antenna pointing. Finally, the space geometric relationship is used to strictly derive the precise adjustments on the elevation and azimuth in order for correcting the antenna pointing error, and the indirect relationship between the main reflector deformation and the pointing error is constructed. This has certain guiding significance for improving the pointing accuracy of large radio antennas.     

基于单目视觉的天线副面并联调整机构相对位姿测量方法

为测量天线副面并联调整机构的相对位姿,研究了一种基于单目视觉的位姿测量系统.采用光源照射固定于动平台上的合作目标,结合滤光片等控制手段,利用单目相机采集非共面特征点的图像,获得高对比度的准理想图像.经过图像处理和平方加权质心法,提取出特征点的图像坐标,使用EPnP (Efficient Perspective-n-Point)算法进行位姿解算,最终可以得到并联调整机构的相对位姿测量方法.最后通过实验进行了精度验证,结果表明平移精度为0.1 mm,旋转精度为0.05°,满足了实验要求,为并联机构的位姿检测提供了可行性思路.     

抛物面天线微波全息测量及结果分析

就上海佘山25 m抛物面天线上进行的相位相关法微波全息测量及其测量结果做了一定阐述。文章首先简要提到了微波全息测量技术在国内外的发展情况以及理论依据,其次介绍了我们所建立的测量系统的组成,重点讨论了基于窄带信号测量工作的有效性和准确性,采用自校准的数据处理手段,对测量误差做了估计和实际测试。当前我们已经取得了0.14 mm的测量精度(极限误差为0.2 mm),并分析了影响测量精度的各项因素。