敞开酸溶-电感耦合等离子体质谱法同时测定钨矿石和锡矿石中14种微量元素

钨矿石和锡矿石成分复杂,具有丰富的共生或伴生元素。在国家标准方法中,对其中的微量共生或伴生元素含量多采用单元素测定,分析强度大,效率低。本文采用混合酸在敞开体系中消解样品,以50%盐酸提取盐类,电感耦合等离子体质谱仪(ICP-MS)同时测定钨矿石和锡矿石中的锂钪铬钴镍铜铅锌铷钼铯锑铋钍等14种微量元素。通过比较碱熔法、盐酸+氢氟酸+硝酸+高氯酸四酸溶矿法、氢氟酸+硝酸+高氯酸三酸溶矿法这三种样品前处理方法,确定选择使用氢氟酸+硝酸+高氯酸三酸溶矿法溶解样品。ICPMS测定过程中,选择铑和铼作为内标元素,有效监控分析信号的漂移。测定结果表明,各元素的检出限为0.003~1.64μg/g,相对标准偏差在0.1%~3.1%,方法回收率在93.1%~104.3%。方法应用于实际钨矿石和锡矿石分析,测定结果与各元素标准测定值吻合较好。相对于传统处理方法,本法一次溶样,多元素同时测定,使分析效率得到了有效提高,更适合大批量多元素钨矿石和锡矿石样品的分析。     

五酸和硝酸微波消解法结合ICP-OES技术测定多金属矿中多种元素的对比研究

快速、准确测定多金属矿中的主次量元素需要根据多金属矿的具体类型选择不同的预处理方法。本文采集我国典型区域的铅锌、锡、钼、钒和铜镍等5种多金属矿,对比了盐酸-硝酸-高氯酸-氢氟酸-硫酸五酸微波消解和硝酸微波消解的溶样效果,应用电感耦合等离子体发射光谱法(ICP-OES)测定铜铅锌锡钨钼锰钛钒9种元素。通过国家标准物质分析验证,五酸微波消解的溶样时间较长,但一次可测定铜铅锌钼锰钒6种元素;硝酸微波消解的溶样时间短,但一次只能测定铜铅锌钼4种元素;两种方法的准确度和精密度高(RSD5%),检出限低(5.3~30 mg/kg),均适合在地质行业推广应用。而由于锡钨钛3种元素不能完全被酸溶解,上述两种消解方法均不适合。     

电感耦合等离子体发射光谱法同时测定锡矿石中锡钨钼铜铅锌

锡矿石是难分解的矿物,共生与伴生元素多,其中的锡钨钼在单一盐酸溶液中易沉淀,准确测定锡矿石中的主次量元素一直是分析技术难点。本文以过氧化钠为熔剂,高温熔融样品,在酒石酸-盐酸-双氧水体系中进行酸化,选用该矿种中仅含有少量的钴作为内标,建立了电感耦合等离子体发射光谱同时测定锡矿石中锡钨钼铜铅锌的分析方法。方法线性范围为0.00~40.0 mg/L;方法检出限为锡10 mg/kg,钨30 mg/kg,钼3.3 mg/kg,铜12 mg/kg,铅15 mg/kg,锌40 mg/kg;方法精密度(n = 9)小于5.0%,实际样品的测定值与传统化学方法及国家标准方法的测定值吻合较好。本方法采用过氧化钠碱熔锡矿石,溶样彻底,并省去了氢氟酸挥发硅的蒸酸过程,节约了样品处理时间;采用酒石酸-双氧水-盐酸体系溶解熔融物,有利于溶液中的锡钨钼形成稳定的络合物,避免了单纯盐酸体系下产生钨酸、钼酸和锡酸沉淀导致测定结果偏低的问题。     

敞口酸熔-电感耦合等离子体发射光谱法测定稀有多金属矿选矿样品中的铌钽和伴生元素

稀有多金属矿各类选矿样品中同一元素的含量相差较大,且同一样品中各元素的含量也有较大差异,如铌钽锂铍在尾矿和原矿中的含量只有几十至几百!g/g,而在精矿中的含量达到百分之几至百分之几十,伴生元素如钾、钠在不同样品中也有较大差异。应用敞口酸熔-电感耦合等离子体发射光谱法(ICP-OES)测定铌钽锂铍等元素通常采用三酸或四酸分解样品,多是测定尾矿、原矿及部分中矿样品中较低含量的铌钽锂铍,且同一测定体系中只测定了一种或两种元素。本文采用氢氟酸-硝酸-盐酸-高氯酸-硫酸分解样品,以3~4滴氢氟酸+5%硫酸+5%过氧化氢提取体系替代常规的有机酸(酒石酸等)提取体系,实现了应用ICP-OES同时测定稀有金属矿选矿试验各阶段产品中不同含量的铌钽锂铍钾钠铷铁钛等元素。各元素的谱线强度在0~500μg/mL浓度范围内呈良好的线性关系,相对标准偏差为0.37%~4.77%(n=6)。该方法提高了选矿全流程样品中各类元素的分析效率,已在选冶试验流程样品分析中得到了应用。     

电感耦合等离子体发射光谱法测定西藏矽卡岩型铜多金属富矿石中8种成矿元素

矽卡岩型铜多金属富矿石是西藏特有矿产,具有成矿元素多样且含量普遍较高的特点,矿物类型主要为硫化物型,成矿元素有Cu、Pb、Zn、Fe、Ag、Bi、Cd、Co等。采用湿法处理此类样品时常因银、铅等元素含量较高出现难溶解、易沉淀现象,导致测定结果偏低。本文采用盐酸预处理、硝酸-氢氟酸-高氯酸溶矿体系,能有效除去样品中的硫,样品分解效果好,选择稀释倍数为1000、溶液介质为10%盐酸,样品溶液不会产生沉淀,采用电感耦合等离子体发射光谱法测定各待测元素均可获得较好的准确度、精密度。方法测定范围为:Cu 0.0056%~20.0%,Pb 0.0087%~20.0%,Zn 0.0031%~20.0%,Fe 0.0090%~20.0%,Ag 5.40~3000μg/g,Bi 10.8~5000μg/g,Cd 0.69~5000μg/g,Co 2.09~5000μg/g。用国家标准物质进行验证,方法准确度小于5.40%,精密度(RSD,n=11)小于4.41%。该方法具有前处理流程简单、分析速度快、同时测定元素多、线性范围宽等优点,经实际样品测试与不同方法分析数据吻合。     

高频红外碳硫仪测定重晶石和黄铁矿中的硫

硫酸盐矿石和硫化物矿石大部分是低电磁性的物质,利用高频红外碳硫仪测定这类矿石中的硫时,在燃烧过程中难以产生较大的电磁感应涡流,导致矿石中的硫释放不完全,造成硫的测定结果偏低。本文采用二氧化硅将重晶石精矿和黄铁矿精矿稀释成不同硫含量的重晶石和黄铁矿样品,通过优化称样量及助熔剂等测试条件,建立了使用高频红外碳硫仪测定重晶石和黄铁矿中硫含量的分析方法。结果表明:当样品中的硫含量高于2%时确定称样量为0.07 g,当硫含量低于2%时确定称样量为0.1 g,加入助熔剂0.4 g锡粒+0.4 g铁粒+1.5 g钨粒,可使重晶石和黄铁矿中的硫完全释放进入仪器红外吸收区域,硫的回收率提高至95.8%~104.2%(重晶石)和95.3%~105.1%(黄铁矿),分别高于常规红外碳硫仪的回收率(83.39%~91.1%和91.5~97.5%)。本方法精密度高(RSD5%),实现了硫含量的准确测定。     

过氧化钠碱熔-电感耦合等离子体发射光谱法测定钛铝合金中的铬铁钼硅

应用电感耦合等离子体发射光谱法(ICP-OES)测定高钛含量的钛铝合金中铬铁钼硅时,单一酸不能使钛铝合金完全溶解;混合酸溶解样品后仍会出现少量杂质、溶解不完全的现象,且复溶时易出现沉淀现象,即使用浓王水也难以将沉淀再溶解。本实验在700℃温度下,采用过氧化钠进行碱熔20 min,盐酸酸化,建立了应用ICP-OES测定钛铝合金中的铬铁钼硅的方法。实验中采用钛基体匹配的方法降低了试液中钛浓度大于200μg/m L时的钛基体干扰,通过控制过氧化钠使用量来降低待测溶液中的盐分含量保证了测定的稳定性。方法检出限为0.002~0.005μg/m L,测定下限为0.007~0.017μg/m L;采用国家标准物质(GBW02501)进行验证,方法的相对标准偏差(RSD)为0.90%~4.89%,相对误差为1.2%~3.6%,回收率为91.6%~103.8%。本方法与酸溶法相比,样品溶解完全,测定准确、可靠,适用于高钛含量的钛铝合金多元素测定。     

电感耦合等离子体质谱法测定地球化学样品中的硼碘锡锗

在多目标的配套方法中,硼、碘、锡、锗四个元素的分析涉及三个配套方法,发射光谱法测定硼、锡,原子荧光光谱法测定锗,分光光度法或电感耦合等离子体质谱法(ICP-MS)测定碘,分析成本高、检测效率低。本文建立了一种ICP-MS同时测定地球化学样品中硼、碘、锡、锗的方法。样品用过氧化钠熔矿,使难熔元素锡分解完全,熔盐经水提取后加入铼内标,再用阳离子交换树脂分离大量钠盐及大部分阳离子,保证了盐分满足质谱测定的要求。方法检出限分别为硼0.92μg/g、碘0.10μg/g、锡0.29μg/g、锗0.09μg/g,满足多目标测试要求。用国家一级标准物质验证,测定值与认定值一致,相对标准偏差(RSD,n=12)≤5%,适用于批量地球化学样品中硼、碘、锡、锗的测定,样品处理过程简便,检测效率高。     

偏硼酸锂熔融-电感耦合等离子体发射光谱法测定钨钼矿石中钨钼及11种伴生元素

钨钼矿石是重要的战略性矿产资源,中国是钨钼矿的产出和消费大国,准确、高效地分析钨钼及其共伴生的有益有害元素含量对钨钼矿的矿床评价和综合利用有重要意义。钨钼矿石中钨钼及伴生元素的分析目前主要采用酸溶和碱熔方式消解样品,酸溶方式在处理高钨钼样品时无法克服水解问题,过氧化钠、氢氧化钠等碱熔方式通常会引入大量碱金属,不能完成钾钠的测定。本文建立了一种偏硼酸锂熔融,盐酸-酒石酸超声浸取,电感耦合等离子体发射光谱(ICP-OES)同时测定钨钼矿石中钨钼铜铅锌铝铁钙镁钛锰钾钠的方法。利用偏硼酸锂熔融的强解离作用使样品完全分解,溶液除硼锂外不引入其他金属元素,在盐酸提取液中加入酒石酸络合能够有效抑制钨钼水解,经超声浸取加快了熔块溶解。实验优化了各元素的分析谱线和观测方式,对熔剂用量以及仪器条件进行对比实验以获得最佳条件,采用基体匹配法绘制标准曲线消除了基体效应的影响。标准曲线线性相关系数均大于0.9990,方法检出限为1.34～46.2μg/g,标准物质测定结果的相对误差为0.14%～8.7%,相对标准偏差(RSD,n=10)为1.4%～7.6%。该方法能够准确、高效地完成钨钼矿石样品中多元素的同时测定。     

敞口酸熔ICP-OES法测定稀有多金属矿选矿样品中的铌钽和伴生元素

稀有多金属矿各类选矿样品中同一元素的含量相差较大,且同一样品中各元素的含量也有较大差异,如铌钽锂铍在尾矿和原矿中的含量只有几十至几百g/g,而在精矿中的含量达到百分之几至百分之几十,伴生元素如钾、钠在不同样品中也有较大差异。应用ICP-OES法测定铌钽锂铍等元素通常采用三酸或四酸分解样品,多是测定尾矿、原矿及部分中矿样品中较低含量的铌钽锂铍,且同一测定体系中只测定了一种或两种元素。本文采用氢氟酸-硝酸-盐酸-高氯酸-硫酸分解样品,以3~4滴氢氟酸+5%硫酸+5%过氧化氢提取体系替代常规的有机酸(酒石酸等)提取体系,实现了应用ICP-OES同时测定稀有金属矿选矿试验各阶段产品中不同含量的铌钽锂铍钾钠铷铁钛等元素。各元素的谱线强度在0~500μg/mL浓度范围内呈良好的线性关系,相对标准偏差为0.61%~4.77%(n=6)。该方法提高了选矿全流程样品中各类元素的分析效率,已在选冶试验流程样品分析中得到了应用。     

Wavelength-dispersive X-ray fluorescence spectrometric determination of Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites

Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.     

高压微波消解法测定醋酸纤维过滤器采集的微尘粒子中的砷镉钴铬铜铁锰镍铅钒锌

最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提     

硅酸盐类样品中硅、铁、铝、钛、锰、钙、镁、钾、钠和磷的x射线荧光光谱测定

本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。     

Isotopic systematics of He,Ar, S,Cu, Ni,Re, Os,Pb, U,Sm, Nd,Rb, Sr,Lu, and Hf in the rocks and ores of the Norilsk deposits

This paper reports the first results of a study of 11 isotope systems (³He/⁴He, ⁴⁰Ar/³⁶Ar, ³⁴S/³²S, ⁶⁵Cu/⁶³Cu, ⁶²Ni/⁶⁰Ni, ⁸⁷Sr/⁸⁶Sr, ¹⁴³Nd/¹⁴⁴Nd, ^206–208Pb/²⁰⁴Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.     

Viscous, cohesive, non-Newtonian, depositing, radial slurry flow

Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.     

硅酸盐中铁、锰、钛、钙、钾、磷、硅、铝、镁、钠、锶、铷、钡的X-射线荧光光谱定量测定

本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。     

岩石密度和超高压岩石折返速率

在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。     

Bellechester,Minnesota, USA,lagoon collapses

Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×10⁶ 1 of partially treated effluent and about 600 m³ of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.     

Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA

The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.     

滇东南花岗岩与锡、银、铜、铅、锌多金属矿床的成因关系

滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.