熔融制样X射线荧光光谱法测定含硫量高的石膏矿物中主次量元素

X射线荧光光谱法(XRF)已经应用于石膏等非金属矿物的测定,但由于石膏标准物质匮乏、硫含量较高且在高温易挥发损失,给测定带来了一定困难。本文采用石膏标准物质、高纯硫酸钙和其他国家一级标准物质(土壤、水系沉积物、碳酸盐)配制人工标准物质拟合校准曲线,优化稀释比、熔矿温度等熔融制样条件,用理论α系数校正基体效应,建立了采用XRF同时测定石膏矿中10个主次量元素(硅铝铁钙镁钾钠钛硫锶)的分析方法。样品与四硼酸锂-偏硼酸锂熔剂的稀释比为1∶9,在1050℃温度下样品熔融完全。方法检出限为4~135μg/g,精密度(RSD,n=12)小于3.0%。本方法配制的人工校准样品加强了样品基体的适应性,使用的四硼酸锂-偏硼酸锂熔剂在样品熔融过程中可有效地结合硫,抑制了硫的挥发损失,适用于批量分析硫含量高达12.60%~51.91%的实际石膏矿物。     

较低稀释比熔融制样X射线荧光光谱法分析铬铁矿

铬铁矿属难熔矿物,目前对铬铁矿的分析以化学分析为主,方法成熟,但操作麻烦且步骤繁琐;而应用X射线荧光光谱法进行分析测定,一般都采用较高稀释比熔融制样,不利于低含量元素的测定。本文选用四硼酸锂+偏硼酸锂作为混合熔剂,与样品以20:1的稀释比熔融制样,利用波长色散X射线荧光光谱测定铬铁矿中多种元素(Cr、Si、Al、TFe、Mg、Ca、Mn)的方法。采用多种铬铁矿标准物质和人工配制标准物质制作工作曲线,理论α系数及康普顿散射内标法校正元素间的吸收-增强效应,方法精密度(RSD,n=10)为0.2%~5.3%。方法检出限低,如锰元素的检出限可低至60 μg/g;镁元素的检出限为225 μg/g,比文献采用高稀释比XRF测定的方法检出限(250 μg/g)要低。本方法通过选择有效的熔剂和较低的稀释比解决了铬铁矿的制样问题,熔剂的用量减少,称样量增加,提高了低含量元素分析的准确度,相应地降低了分析成本。     

较低稀释比熔片制样X射线荧光光谱法测定磷矿石中12种主次痕量组分

当前应用X射线荧光光谱熔片制样技术分析测定较低含量、低荧光产额氟组分时,准确度较低,精密度较差、检出限较高。本文运用5:1较低稀释比熔样制片技术,采用波长色散X射线荧光光谱法测定磷矿石中12个主次量组分(F、Na₂O、MgO、Al₂O₃、SiO₂、P₂O₅、K₂O、CaO、TiO₂、MnO、TFe₂O₃和痕量SrO)。采用磷矿石、岩石国家一级标准物质、磷矿石管理样品和人工配制标准样品校准,经验系数法进行基体校正,结果表明12个组分分析方法的精密度和准确度较好,检出限较低,未知样品的分析结果比较满意;氟的精密度、准确度和检出限均好于文献中10:1熔样稀释比得出的结果。该方法解决了压片制样测定氟组分,熔片制样测定其他主次量组分的技术问题,同时也降低了熔片制样技术测定氟的检出限。     

熔融制样X射线荧光光谱法测定锑矿石中的锑和14种微量元素

锑矿石分析通常分别采用酸分解系统和碱熔系统,萃取分离后应用容量法、原子吸收光谱法、原子荧光光谱法等分析手段进行单项测定,样品处理繁琐、操作复杂,分析过程常因熔矿不完全而导致结果偏低或失真,难以满足地质测试的需要。本文建立了玻璃熔融制样,波长色散X射线荧光光谱测定锑矿石中的锑及14种次量元素与伴生元素(Cu、Pb、Zn、As、Co、Ni、W、Ba、S、SiO₂、Al₂O₃、TFe、CaO、MgO)的快速分析方法。用国家标准物质和人工合成标准参考物质拟合校准曲线,对熔融条件进行了研究。确定样品与四硼酸锂-偏硼酸锂-氟化锂复合熔剂的熔融稀释比例为1:20,以硝酸铵为氧化剂,碳酸锂为保护剂,700℃预氧化,在1050℃温度下熔融完全,有效地防止了As、S的挥发损失,解决了化学法测试样品处理复杂、不能同时测定多元素、测试元素偏少的问题。一些元素的检出限为Sb 0.14%,Cu 0.0027%,Pb 0.0025%,Zn 0.0046%,As 0.0028%,S 0.021%;方法精密度(RSD,n=12)小于5%;选用合成标准物质和实际生产锑矿试样进行验证,测定结果与参考值或化学值一致性良好。本法大部分元素检出限都要稍高于粉末压片法,但操作简单,测试范围更宽,适用于实验室对不同锑矿矿种批量样品中多元素快速、准确检测的需要。     

低稀释比制样技术与多类型地质样品X射线荧光分析方法研究

研究制定了在X射线荧光光谱分析中适用于多类型地质样品的低稀释比制样技术。确定了四硼酸锂和偏硼酸锂混合试剂作为熔剂，使用m样品:m熔剂=1:3的稀释比制样，对4种不同种类的地质材料进行了实验，并采用基本参数法和理论α系数法校正基体效应，得到了准确度较高的定量分析结果。     

熔融制样波长色散X射线荧光光谱法测定白云石中钙镁硅铁铝

白云石属碳酸盐矿物,应用熔融制样X射线荧光光谱法测定其中主次量组分钙、镁、硅、铁、铝时,由于白云石灼烧减量大,在试料片制备过程中,如果以干基试料制备试料片,除灼烧减量外还有少量其他组分被分解出的大量CO₂带走,导致试料损失,测定结果偏低;如果以灼烧基试料制备试料片,由于灼烧后的试料极易吸收空气中的水分和CO₂,同样使测定结果偏低。基于质量守恒原理,本文直接以灼烧减量测量后的灼烧基试料质量作为试料量(即灼烧减量测定所称量的干基试料量扣除灼烧减量的量),以四硼酸锂为熔剂,5%碘化铵溶液为脱模剂,试料与熔剂的稀释比为1:10,于1050℃熔融15 min以上制备的试料片透彻、玻璃化程度高。以白云石标准物质和标准样品作为标准试料,制作各组分的标准曲线的相关系数在0.9940~0.9994之间;方法检出限为0.011%~0.48%;标准物质和标准样品的测定值与认定值基本一致,各组分的相对标准偏差(RSD,n=11)在0.5%~1.7%之间,方法具有较好的重现性。本方法以1050℃灼烧后的试样作为试料制备XRF分析样片,最大限度地降低了灼烧减量因素(空气中的水分和CO₂)对测定结果的影响,适用于白云石及其煅烧物中钙、镁、硅、铁、铝等组分的同时测定。     

熔融制样X射线荧光光谱法测定珍珠岩矿中主量元素

珍珠岩矿的化学成分对其膨胀特性有重要影响,是珍珠岩矿的重要质量指标,目前大多采用容量法、重量法、分光光度法、原子吸收光谱法等传统方法对各化学成分进行测定,操作复杂,而且不能满足主量元素同时测定的要求。本文采用熔融法制样,建立了X射线荧光光谱同时测定珍珠岩矿中主量元素(Si、Al、Fe、Ca、Mg、Ti、K、Na)的分析方法。样品制备试验结果表明,试样与四硼酸锂-偏硼酸锂(质量比67∶33)混合熔剂稀释比为1∶10,熔融温度为1050℃时,样品熔融完全,制备的熔片满足分析方法的要求,且克服了珍珠岩矿高温熔矿时由于膨胀不均匀而导致硅元素测量结果偏低的问题。通过仪器测量条件的优化,以国家标准物质和自制校准样品拟合校准曲线,并进行基体效应校正,实际矿区样品测量结果与化学分析法的测定值基本吻合。方法检出限小于0.05%,精密度(RSD,n=12)小于1.5%。本方法与经典分析方法相比,简便高效、绿色环保、精密度高、准确度好,一次熔矿能够同时测定珍珠岩矿中全部主量元素,满足了珍珠岩矿快速分析测试的需要。     

云南三江地区典型金矿床吨位-边界品位曲线特征

吨位-平均品位-边界品位曲线是矿床评价的重要参考,也是理解成矿过程的一个窗口。本文借助吨位-平均品位-边界品位分形模型,选取我国三江地区典型金矿床的局部地段矿体——北衙万硐山磁铁矿-赤铁矿型矿体、镇沅冬瓜林浸染状低温硫化物型矿体、大龙潭氧化硫化物型矿体以及勐满热水塘强硅化泥化蚀变的热泉型矿体;热水塘主要为低品位矿石,而其它三个矿床品位相对较高;分别计算了四个金矿床的吨位-边界品位曲线,并分析其特征。文章提出矿化分散指数(MDI),将其定义为K_o=－ΔO/ΔG_c,K_m=－ΔM/ΔG_c(ΔG_c为两个边界品位之差,ΔO与ΔM分别为相对应的矿石量与金属量之差);K_o与K_m值越小,表明空间中金属分布相对分散。文中分析的四个金矿床的曲线均是低边界品位区间的矿化分散指数较高(MDI₁,即K_o1,K_m1),高边界品位区间的矿化分散指数相对较低(MDI₂,即K_o2,K_m2);说明在不同类型金矿床中,高品位区间比低品位区间的金属空间分布更加分散。K_o1和K_o2由高到低依次为热水塘、大龙潭、万硐山和冬瓜林,K_m1和K_m2由高到低依次为热水塘、万硐山、大龙潭和冬瓜林。热水塘的矿化分散指数比其他三个矿床高,说明热泉型金矿成矿元素空间分布比较集中。     

华北地块南缘老牛山杂岩体时代、成因及地质意义——锆石年龄、Hf同位素和地球化学新证据

老牛山杂岩体位于华北地块南缘。野外侵入关系和锆石LA-ICP-MS U-Pb定年显示,其由晚三叠世(印支期)和晚侏罗(燕山期)花岗质岩石组成。印支期岩石类型为石英二长岩、石英闪长岩和粗粒黑云母二长花岗岩,年龄分别为223±1Ma、222±1Ma和214±1Ma; 燕山期为中粒-中粗粒黑云母二长花岗岩和细粒-中细粒黑云母二长花岗岩,年龄分别为152±1Ma和146±1Ma。印支期石英闪长岩、石英二长岩的SiO₂相对含量低、富碱、高铝,为钾玄系列,准铝质Ⅰ型花岗岩;印支期粗粒黑云母二长花岗岩具富硅、碱、高铝、低镁的特点,属于高钾钙碱性系列,为准铝质-过铝质Ⅰ型花岗岩;燕山期黑云母二长花岗岩具高硅和铝、富碱,低镁的特点,为高钾钙碱性系列,准铝质Ⅰ型花岗岩。组成老牛山杂岩体的花岗岩从早到晚SiO₂含量由低变高,MgO、CaO和Na₂O由高变低。各期次岩石均表现出稀土元素总量较高,轻稀土元素明显富集,轻、重稀土元素分馏明显,具有较弱的铕异常。两期花岗质岩石均富集大离子亲石元素(K、Rb、Ba、Sr),而相对亏损高场强元素(Nb、Ta、P)。印支期花岗质岩石的全岩ε_Nd(t)为-11.3~-14.87,t_DM为1.7~1.9Ga,锆石的ε_Hf(t)为-9.57~-25.11,t_DM2为1863~2841Ma;燕山期花岗岩的全岩ε_Nd(t)为-13.32~-16.83,t_DM为 1.7~1.9Ga,锆石的ε_Hf(t)为-18.28~-24.79,t_DM2 为2360~2767Ma,表明该杂岩体的源区物质以壳源物质为主,可能与太古宙太华群相似,印支期有年轻地幔物质贡献。     

铬天青S光度法及非线性拟合测定高纯硅中微量铝

铬天青S光度法是硅中铝含量的测定方法之一,该方法的标准曲线大多采用不过零点的线性拟合,导致低铝含量测定误差大。为提高方法准确度并降低方法检出限,研究了铝标准曲线低浓度部分的拟合问题,探讨了不同拟合模型对检测结果准确度的影响。实验结果表明,不同浓度铝标准液的吸光度在0~0.3 μg/mL范围内并不满足一次函数线性关系,采用三次函数关系y=-17.45230x³+10.42883x²+1.04047x (y为扣空白的吸光度,x为铝的质量浓度)拟合能获得良好结果,其相关系数R²为0.99975。利用已知铝含量的硅试液检验该公式,其相对标准偏差(RSD)为2.55%。样品中铝的测定值与电感耦合等离子体发射光谱法测定值吻合。该法可以显著提高低浓度的铝测定的准确性,可用于测定高纯硅中含量在0.55 μg/g以上的铝杂质。     

Elastic and thermoelastic properties of synthetic Ca<Subscript>2</Subscript>MgSi<Subscript>2</Subscript>O<Subscript>7</Subscript> (åkermanite) and Ca<Subscript>2</Subscript>ZnSi<Subscript>2</Subscript>O<Subscript>7</Subscript> (hardystonite)

Elastic and thermoelastic constants of large single crystals of Ca₂MgSi₂O₇ and Ca₂ZnSi₂O₇ have been derived from ultrasonic resonance frequencies of plane-parallel plates and their shift upon variation of temperature, respectively. In addition, coefficients of thermal expansion and dielectric constants were determined. Both species possess quite similar properties. As observed in other isotypic magnesium and zinc compounds, the mean elastic stiffness and the deviation from the Cauchy relations are significantly larger in the zinc compound, due to a covalent contribution of the Zn–O bond. Positive thermoelastic constants T₄₄ and T₆₆ in Ca₂MgSi₂O₇ allow temperature-independent ultrasonic generators and oscillators to be manufactured.     

硅酸盐玻璃中的Na和K含量电子探针分析条件设定探讨

含Ti硅酸盐玻璃在基础科学研究和应用技术开发上均有重要价值,亟需对其进行准确的成分分析,为进一步的科研工作提供重要的数据支撑.对玻璃进行电子探针分析时,由于样品的易损性和其中(Na和K)阳离子在电子束轰击下极易发生迁移和扩散,因此往往需要经过条件实验来确定合适的分析条件,确保样品在该条件下能够保持尽量稳定的状态,才能获...     

Hydrometallurgical processing and recovery of molybdenum trioxide from spent catalyst

Hydrometallurgical processing of spent hydrodesulphurisation (HDS) catalyst for the recovery of molybdenum using sodium carbonate and hydrogen peroxide mixtures was investigated. The results indicated that the recovery of molybdenum was largely dependent on the concentrations of Na₂CO₃ and H₂O₂ in the reaction medium, which controls the acidity of the leach liquor and carry over of impurities such as Al, Ni, P, Si and V. Leaching process was exothermic and leaching efficiency of molybdenum decreased with increasing solid to liquid ratio. Large scale leaching of spent catalyst, under optimum conditions: 20% pulp density, 85 g/L Na₂CO₃, 10 vol.% H₂O₂ and 1 h reaction, resulted a leaching efficiency of 84% Mo. The obtained leach liquor contained (g/L): Mo — 22.0, Ni — 0.015 and Al — 0.82, P — 1.1, Si — 0.094 and minor quantities of V — 8 mg/L, As and Co — < 1 mg/L. Recovery of Mo from leach solution as MoO₃ of 97.30% purity was achieved by ammonium molybdate precipitation method.     

A computer simulation study of OH defects in Mg2SiO4 and Mg2GeO4 spinels

Classical atomistic simulation techniques have been used to investigate the energies of hydrogen defects in Mg₂SiO₄ and Mg₂GeO₄ spinels. Ringwoodite (γ-Mg₂SiO₄) is considered to be the most abundant mineral in the lower part of the transition zone and can incorporate large amounts of water in the form of hydroxyls, whereas the germanate spinel (γ-Mg₂GeO₄) corresponds to a low-pressure structural analogue for ringwoodite. The calculated defect energies indicate that the most favourable mechanisms for hydrogen incorporation are coupled either with the reduction of ferric iron or with the creation of tetrahedral vacancies. Hydrogen will go preferentially into tetrahedral vacancies, eventually leading to the formation of the hydrogarnet defect, before associating with other negatively charged point defects. The presence of isolated hydroxyls is not expected. The same trend is observed for germanate, and thus γ-Mg₂GeO₄ could be used as a low-pressure analogue for ringwoodite in studies of water-related defects and their effect on physical properties.     

水射流破碎联合CO2置换开采天然气水合物新工艺及实验研究

本文对目前开采天然气水合物的5种方法进行了归纳总结,重点分析了CO₂置换开采以及固体开采法,并通过分析这2种开采方法的优劣势,提出了水射流冲蚀、破碎海洋天然气水合物储层联合CO₂置换开采天然气水合物的新思路。水射流冲蚀、破坏水合物储层后形成的采空区能为CO₂提供更好的储藏空间并提高其与储层的作用面积,提高置换效率;封存的CO₂水合物也可以提高水合物储层的稳定性,具有良好的互补效应。实验结果表明,在整个置换过程中,含采空区储层CH₄置换率为24.3%,CO₂封存率为22.1%;完整储层CH₄置换率为15.3%,CO₂封存率为20.9%,置换率提升约59%,封存率提升约5.7%。采空区的作用主要体现在提升水合物置换介质的注入量上。     

流体包裹体盐度低温拉曼光谱测定方法研究

氯盐溶液作为流体包裹体中最普遍和最重要的盐水化合物,是测定包裹体盐水溶液含盐度的主要溶质,但由于其强离子键化合物的分子特性在常温、常压下没有拉曼效应,拉曼光谱测试无法获取氯盐的有效特征信息,使得利用拉曼光谱研究流体包裹体分子组分及含盐度的方法存在严重缺陷。本文联合利用激光拉曼光谱探针和冷热台,原位采集了不同盐度的NaCl-H₂O和CaCl₂-H₂O标准盐水溶液在低温下(-185℃)形成的冰、NaCl水合物和CaCl₂水合物的拉曼光谱,分析了不同盐度标准盐水溶液形成的水合物拉曼特征峰的变化规律,尝试建立流体包裹体盐度低温拉曼光谱测定方法。分析表明,NaCl水合物约3425 cm^-1拉曼特征峰与冰约3120 cm^-1拉曼特征峰峰面积比值和配制的NaCl-H₂O标准溶液盐度呈良好的正相关(r²=0.9995),CaCl₂水合物约3431 cm^-1拉曼特征峰与冰约3120 cm^-1拉曼特征峰峰面积比值也和配制的CaCl₂-H₂O标准溶液盐度呈较好的正相关(r²=0.9458)。利用愈合人工水晶法合成的NaCl-H₂O和CaCl₂-H₂O包裹体标样检验了用上述方法低温测定流体包裹体盐度的可靠性,结果表明该技术用于盐度大于0.5 mol/L的NaCl-H₂O体系流体包裹体时,数据精度好于20%;用于盐度大于0.5 mol/L的CaCl₂-H₂O体系流体包裹体时,数据精度最高可达5%,完全可达到半定量-定量测定的要求。研究还发现,包裹体内压可能对低温拉曼光谱测定流体包裹体盐度影响不大,分析中获得的冰拉曼特征峰的拉曼位移(约3120 cm^-1)与前人略有差异,可能与实验条件下获得的冰的多型不同有关。与国内外同行的研究结果比较,本研究更加注重该项实验技术的实际应用,通过对不同体系盐水溶液系列进行拉曼光谱实验分析,对实验条件和方法进行不断优化,在确定流体体系的同时实现了包裹体盐水溶液盐度半定量-定量测定,准确度优于传统方法,并且该方法具有很强的实用性。     

Interpretation of carbon dioxide diffusion behavior in coals

Storage of carbon dioxide in geological formations is for many countries one of the options to reduce greenhouse gas emissions and thus to satisfy the Kyoto agreements. The CO₂ storage in unminable coal seams has the advantage that it stores CO₂ emissions from industrial processes and can be used to enhance coalbed methane recovery (CO₂-ECBM). For this purpose, the storage capacity of coal is an important reservoir parameter. While the amount of CO₂ sorption data on various natural coals has increased in recent years, only few measurements have been performed to estimate the rate of CO₂ sorption under reservoir conditions. An understanding of gas transport is crucial for processes associated with CO₂ injection, storage and enhanced coalbed methane (ECBM) production.A volumetric experimental set-up has been used to determine the rate of sorption of carbon dioxide in coal particles at various pressures and various grain size fractions. The pressure history during each pressure step was measured. The measurements are interpreted in terms of temperature relaxation and transport/sorption processes within the coal particles. The characteristic times of sorption increase with increasing pressure. No clear dependence of the characteristic time with respect to the particle size was found. At low pressures (below 1 MPa) fast gas diffusion is the prevailing mechanism for sorption, whereas at higher pressures, the slow diffusion process controls the gas uptake by the coal.     

Quick-look assessments to identify optimal CO2 EOR storage sites

A newly developed, multistage quick-look methodology allows for the efficient screening of an unmanageably large number of reservoirs to generate a workable set of sites that closely match the requirements for optimal CO₂ enhanced oil recovery (EOR) storage. The objective of the study is to quickly identify miscible CO₂ EOR candidates in areas that contain thousands of reservoirs and to estimate additional oil recovery and sequestration capacities of selected top options through dimensionless modeling and reservoir characterization. Quick-look assessments indicate that the CO₂ EOR resource potential along the US Gulf Coast is 4.7 billion barrels, and CO₂ sequestration capacity is 2.6 billion metric tons. In the first stage, oil reservoirs are screened and ranked in terms of technical and practical feasibility for miscible CO₂ EOR. The second stage provides quick estimates of CO₂ EOR potential and sequestration capacities. In the third stage, a dimensionless group model is applied to a selected set of sites to improve the estimates of oil recovery and storage potential using appropriate inputs for rock and fluid properties, disregarding reservoir architecture and sweep design. The fourth stage validates and refines the results by simulating flow in a model that describes the internal architecture and fluid distribution in the reservoir. The stated approach both saves time and allows more resources to be applied to the best candidate sites.     

碱处理对河北围场天然沸石结构和性能的影响及其机理研究

采用NaOH对围场地区天然沸石进行处理,采用X射线衍射仪、红外光谱仪、N_2吸附-脱附技术、扫描电子显微镜等对材料进行表征分析,采用水蒸气吸附法评价材料的亲水性,采用Cr~(3+)和Mn~(2+)评价材料的离子交换性能,探讨了碱处理对天然沸石的结构、亲水性和离子交换性能的影响及其机理。实验结果表明,围场地区天然沸石中主要含有斜发沸石、石英和伊利石;碱处理可降低天然沸石的硅铝比,且沸石的硅铝比随着碱处理浓度的提高而不断降低;碱处理对斜发沸石结构的影响较石英和伊利石更大;高浓度碱处理导致天然沸石的结构发生破坏,比表面积降低,孔体积提高;伴随着天然沸石硅铝比的降低,其亲水性和离子交换性能不断提高。