Field Study on the Behavior of Destructive and Non-Destructive Piles Under Compression

This paper presents a series of full-scale load tests on long bored piles instrumented with strain gauges along the shafts, including eight field tests of piles loaded to failure and one non-destructive pile load test. The load-displacement response, skin friction, end resistance, and the threshold of the pile-soil relative displacement for fully mobilizing skin resistance were discussed. A simple softening model was proposed to describe the degradation behavior of the skin friction along the pile-soil interface and the load-displacement relationship developed at the pile base. It is found that the shaft resistance degradation investigated in the non-destructive load test only occurs at a shallow depth, and the skin friction of deeper soil is not fully developed. However, unlike the results of the non-destructive load tests, the softening is accompanied by a reduction in skin friction and observed to be along the whole pile depth. The thresholds of pile-soil relative displacement for fully mobilizing skin resistances in different soils have been found to be in the range 0.6% to 2.4% of the pile diameter. Moreover, in practical applications, a bilinear model is assumed to be feasible in analyzing the load-settlement relationship developed at the end of non-destructive pile, whereas the load transmission curve of the soils below the pile base corresponds to a softening model in the field tests of piles loaded to failure.     

Field and Theoretical Study of the Response of Super-Long Bored Pile Subjected to Compressive Load

In this article, two full-scale pile loading tests were conducted to observe the field performance of the super-long bored piles, and a simplified approach for nonlinear analysis of the load-displacement behavior of a single pile was presented. The field tests on piles indicates that, under the maximum test load, more than 70% of the pile top settlement is caused by the compression of pile shaft. For practical purposes, the pile top settlement can be reduced through improving the pile shaft strength. When the load reaches the maximum test load, the proportion of the load carried by the pile tip is approximately 30%. The super-long pile is functioning as an end-bearing friction pile. The skin friction at shallow depth is fully mobilized and decreases from a peak value with increasing load. However, the skin friction of deeper soil is not fully developed due to less relative displacement. Furthermore, a BoxLucas1 model is used to capture the relationship between unit skin friction and pile-soil relative displacement, whereas a hyperbolic model is used to describe the relationship between toe stress and pile base displacement. Based on the BoxLucas1 model and the hyperbolic model, a load transfer method is used to clarify the response of a single pile, and a computational flow chart is developed. The efficiency and accuracy of the present method is verified using the field tests on piles. The proposed simple analytical approach is economical and efficient, resulting in savings in time and cost.     

Centrifuge modelling of lateral loading behaviour of a “semi-rigid” Mono-pile in soft clay

Abstract

Mono-pile foundations have been widely used for offshore wind turbines principally due to their convenient construction and cost-effective nature. So far, little attention has been paid to large diameter “semi-rigid” piles that have distinct behaviours from flexible or ideally rigid piles. This paper presents a series of centrifuge model tests to study the deforming and bearing characteristics of a 5.9 dia. semi-rigid pile under lateral loadings in kaolin clay. For monotonic loading, a modified p–y curve analysis model considering rotational soil flow near the rotation centre of pile was proposed, highlighting the limitation of classic plane-strain based plasticity models to evaluate the ultimate lateral pile-soil resistance. For cyclic loading, a strong correlation between the degree of soil degradation and cyclic load amplitude was identified. Besides, a degradation factor model, accounting for various cyclic stress levels and soil depths, was proposed, which can be used to assess the accumulative displacement of semi-rigid piles under cyclic loadings in soft clay.     

Jacked model pile shafts in offshore calcareous soils

Abstract

This paper describes the results of laboratory tests carried out on model pile shafts in a variety of reconstituted calcareous sands and on silica sand. The factors influencing both the skin friction under static loading and the degradation of skin friction under cyclic loading have been investigated. The grading and crushability of the particles appears to have a significant influence on both, with less favourable performance being found for uniformly graded crushable particles. Relative density and overconsolidation ratio also have some influence.

Under cyclic loading, the amplitude of cyclic displacement and, more specifically, the cyclic slip displacement, influence the extent of cyclic degradation of skin friction.     

Model experimental research on uplift single pile in calcareous sand of South China Sea

Vertical uplift static loading tests of single model pile were conducted in the in-lab calcareous sand and quartz sand by emulating practical condition of full-size piles in site. The settlement, lateral deflection, axial force, and friction distribution of the pile are analyzed for each physical test. The pile behaviors in calcareous sand and quartz sand are compared. From the test results, it can be found that the pile top displacement of uplift pile in calcareous sand can be divided into two stages: the pile–sand synchronous stage and pile–sand asynchronous (relative displacement) stage. Data from uplift tests show that the heave of calcareous sand around pile top is very small, which is resulted from the mutually restraint of surface particle. The mutual restriction of surface particle leads to “bottleneck effect” and strengthens ultimate side friction of upper pile segment. In addition, the shear dilatancy and particle breakage of calcareous sand lead to the upper harden and the lower soften of side friction, respectively. Cases of calcareous sand and quartz sand show different responses to pile forming methods, which due to the sands’ different characteristics of particle breakage when compressed as well as plastic deformation under loading–unloading conditions.     

Field Investigations of Two Super-long Steel Pipe Piles in Offshore Areas

A research on super-long piles has been primarily based on cast-in-place bored piles. In this article, field tests associated with selected measuring technologies were conducted on two super-long steel pipe piles in offshore areas to investigate the behaviors and performance of super-long steel pipe piles. The strain along the pile shaft was monitored by adopting the Brillouin optical time domain reflection and fiber Bragg grating techniques. Static load tests were also conducted on two test piles to determine the bearing capacities. In addition, the axial forces, relative displacements between piles and soils and pile shaft resistances were calculated based on the measured strain. According to the results of the static load tests, the ultimate bearing capacities of the two test piles are greater than 15,000 and 15,500 kN. Both of these values meet the design requirements. In addition, the two test piles can be treated as pure friction piles, and the load transfer mechanism and relationships between the pile shafts and relative displacements are also discussed. Finally, recommendations for practical engineering and significant conclusions are presented.     

Response of Single Piles in Marine Deposits to Negative Skin Friction from Long-term Field Monitoring

The behavior of single piles subjected to negative skin friction in soft soil was conducted by analyzing the results from full-scale long-term field measurements and three-dimensional (3D) numerical analyses. A skin friction coefficient (α and β coefficients) of the instrumented piles is back-calculated at different degrees of consolidation (U) of soft marine clay. Back-calculated β-values ranged from 0.15 to 0.35 for clay, and from 0.30 to 0.55 for sand, respectively. In addition, back-calculated α-values ranged from 0.1 to 0.3 for coated pile, and from 0.2 to 0.8 for uncoated pile when undrained shear strength of the soft clay was about 30–60 kPa, respectively. Moreover, this study describes behavior of a pile based on full-coupled 3D finite element (FE) analysis. The appropriate parametric studies needed for verifying the pile-soil interaction with consolidation are presented in this paper. Compared to the results from the measurements, it is shown that the computed results are capable of predicting the pile-soil behavior under consolidation. The major parameters that influence the pile behavior are discussed for different soil-pile conditions.     

A Model Test on the Behavior of a Static Drill Rooted Nodular Pile Under Compression

A static drill rooted nodular pile is a new type of composite pile foundation with high bearing capacity, and mud emissions can be largely reduced using the static drill rooted method. This report presents a model test on the behavior of this composite pile in a test box. The load-displacement response, axial force, skin friction, and mobilized base load are discussed in the report; in particular, the force in the cemented soil was investigated based on the measured data. Moreover, the finite element software ABAQUS was used to help investigate this behavior more thoroughly. It was determined that the function of the cemented soil around the pile shaft was different from that at the enlarged pile base; the stress in the cemented soil around the shaft increased suddenly when nearing the pile base; the ultimate skin friction obtained in the model test was larger than that estimated in the field test; and the relative displacement between the precast nodular pile and the cemented soil could be ignored during the loading process, which corresponded to the result of the field test and demonstrated that the nodular pile and cemented soil act as one entity during the loading process.     

Case study on pile running during the driving process of large-diameter pipe piles

The super-long and large-diameter steel pipe piles are often adopted for the construction of offshore oil platforms in deep sea. One constructability issue related to driving heavy pipe piles is the pile running. The term pile running refers to the quick penetration of a pile into the seabed as a result of its high self-weight and low resistance from the seabed. The unexpected pile running can cause the steel wire of the hammer to break or even the loss of the hammer. A case study of pile running at an oil platform is introduced in this paper. A simplified theoretical method is proposed to explain the mechanisms of the pile running in this case. A factor of friction degradation is proposed to calculate the dynamic skin friction from the static ultimate skin friction of surrounding soil. The comparisons between the predictions to the case history show that the proposed simplified method can be used to predict the pile running condition.     

Field Evaluation of the Vertical Bearing Capacity of a Screw Pretensioned Spun High-Strength Concrete Pile

This study has evaluated the vertical bearing capacity by conducting static load tests for noise-free and vibration-free screw pretensioned spun high-strength concrete (PHC) piles installed using two different methods (end-squirting shoe and pre-boring methods). Vertical bearing capacity differences seem to occur due to the displacement of soils near the external circumference of a pile, depending on the installation method. A method by which to evaluate the bearing capacity of screw concrete piles is suggested by considering the equations that already have been used to calculate the bearing capacity of piles. Based on static load tests and analysis, the pile installed using the end-squirting shoe method was assumed to be a bored pile and it was reasonable to use the equation proposed by the Japanese Geotechnical Society. At the same time, the pile installed using the pre-boring method was deemed a low soil displacement pile and so it was reasonable to apply the equations proposed for calculating the bearing capacity of the driven pile suggested by the Architectural Institute of Japan.     

Degradation of lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading

Abstract

In this article, the degradation of the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading is studied numerically. A modified kinematic hardening constitutive model is employed to simulate the degradation of soft clay after cyclic loading. The modified model is verified by comparing the numerical simulation results with the results of centrifuge model tests. Furthermore, the modified model is applied to numerical simulations for evaluating the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading. The degradation of the lateral bearing capacity of piles in soft clay after different cyclic displacement levels and different numbers of cycles is investigated. The study reveals that the modified kinematic hardening constitutive model can effectively estimate the cyclic degradation behavior of piles in soft clay subjected to cyclic lateral loading. The degradation of the ultimate lateral bearing capacity progresses slowly with increasing cyclic displacement level for fewer cycles, and the degradation develops significantly at higher levels of cyclic displacement after applying a larger number of cycles.     

扩底抗拔桩动态变形全过程承载特性模型试验研究

利用砂土中扩底抗拔桩的模型试验,研究从开始加载到破坏时扩底抗拔桩地基动态变形全过程的承载特性。试验结果表明:半模试验得到的极限荷载和破坏面均略小于全模试验结果,采用半模试验测量地基变形过程与破坏模式有明显优势,用半模试验代替全模试验是可行的;随着桩顶荷载的增加,扩大头上方的土体由压缩变形逐渐发展为局部的压缩—剪切破坏;扩大头对其上部的桩侧摩阻力有增强作用,对其下部的桩侧摩阻力有削弱作用;扩大头在工作荷载、极限荷载和破坏荷载作用时分担的荷载比例为15%~20%。     

A simplified calculation method for axial cyclic degradation of offshore wind turbine foundations in clay

Abstract

Pile foundation is the most popular option for the foundation of offshore wind turbines. The degradation of stiffness and bearing capacity of pile foundation induced by cyclic loading will be harmful for structure safety. In this article, a modified undrained elastic–plastic model considering the cyclic degradation of clay soil is proposed, and a simplified calculation method (SCM) based on shear displacement method is presented to calculate the axial degradated capacity of a single pile foundation for offshore wind turbines resisting cyclic loadings. The conception of plastic zone thickness R_p is introduced to obtain the function between accumulated plastic strain and displacement of soil around pile side. The axial ultimate capacity of single piles under axial cyclic loading calculated by this simplified analysis have a good consistency with the results from the finite element analysis, which verifies the accuracy and reliability of this method. As an instance, the behavior of pile foundation of an offshore wind farm under cyclic load is studied using the proposed numerical method and SCM. This simplified method may provide valuable reference for engineering design.     

Development of Prebored Screw Pile Method and Evaluation of Its Bearing Characteristics

The pile-driving method produces considerable noise and vibrations. Hence, an auger-drilled pile method was developed as a low-noise and -vibration substitute. However, this method does not guarantee the bearing capacity of the pile unless some amount of pile-driving is performed. Therefore, the noise and vibration problems cannot be completely solved. In this study, a prebored screw pile method is proposed to solve these problems. In this method, piles are constructed by the rotary penetration of a screw pile into a prebored hole filled with some cement milk and whose diameter is smaller than that of the screw pile. To determine the shape of the screw pile, laboratory tests with model screw piles were conducted. Also, field load tests were conducted on an actual screw pile fabricated based on the laboratory test result and on a smooth-surfaced pile. In addition, the behavior of the screw pile was estimated by using three-dimensional finite element analysis. The results of the field load test and the numerical simulation showed that the ultimate bearing capacity and the unit skin friction of the screw pile are very superior to those of the smooth-surfaced pile and the cement milk is an important factor in the prebored screw pile method.     

Behaviour of rigid piles in marine clays under lateral cyclic loading

In the field of ocean engineering, pile foundations are extensively used in supporting several structures. In many cases, piles are subjected to significant lateral loads. The environment prevalent in the ocean necessitates the piles to be designed for cyclic wave loading. In this investigation, the behaviour of rigid piles under cyclic lateral loading has been studied through an experimental programme carried out on model piles embedded in a soft marine clay. Static tests were also conducted on piles embedded in a clay bed prepared at different consistencies suitable to field situations. Cyclic load was applied by using a specially designed pneumatic controlled loading system. Tests were conducted on model piles made of mild steel (MS), aluminium and PVC with wide variation in pile soil relative stiffness. For cyclic load levels less than 50% of static lateral capacity, the deflections are observed to increase with number of cycles and cyclic load level and stabilise after a certain number of cycles. For cyclic load levels greater than 50% of static lateral capacity, the deflections are observed to increase enormously with number of cycles. The results of post-cyclic load tests indicate that the behaviour under static load can improve for cyclic load levels less than 40% of the static lateral capacity. The variations in the load capacity due to cyclic loading are explained in terms of the changes in strength behaviour of soil.     

Numerical Analysis of Interaction Between Pile-Supported Pier and Bank Slope

Two- and three-dimensional finite element analysis programs for pile-soil interaction are compiled. Duncan-Chang's Model is used. The construction sequence of the pier is modeled. The pile-soil interface element is used. The influence of the combination type of piles on the deformation of bank slope and pile behaviour is analyzed. Different designs of a pile-supported pier are compared thoroughly. Calculation results show that the stresses and displacements of the pile are directly related to the distance from the bank slope and the direction of inclination. An inclined prop pile set in the rear platform would remarkably reduce the stresses of piles and the displacement of the pier.     

Numerical analysis of bearing capacity of drilled displacement piles with a screw-shaped shaft in sand

Drilled displacement (DD) piles with a screw-shaped shaft (referred to as DD piles) are installed using a continuous full thread hollow rod (without a displacement body) inserted and advanced in the soil by both a vertical force and a torque. As a type of newly developed pile, current understanding of the bearing mechanism of DD piles is unsatisfactory, which restricts their further applications in engineering. The primary aim of this paper is to study the bearing mechanism of this type of pile using a numerical method. First, a numerical model for calculating the bearing capacity of the DD piles was created and validated by a laboratory test. Then, the effects of the parameters of pile–soil interface, soil strength, and pile geometrical parameters on the bearing mechanism of the DD piles were investigated in parametric studies. The results of parametric studies show that the limit shear stress on the pile–soil interface, the friction angle of surrounding sand, screw pitch, and thread width significantly influence the bearing capacity of the DD piles, whereas the friction coefficient at the pile–soil interface and the thread thickness have little effect. Based on the results of the parametric studies, the failure mechanism of the DD piles under vertical load is analyzed. Finally, an equation for predicting the ultimate bearing capacities of helical piles based on cylindrical shear failure was used for estimating the bearing capacity of the DD piles, and the calculated results were verified with the numerical results.     

Lateral cyclic response of an aluminum model pile in sand

Lateral cyclic load tests were performed on an aluminum model pile in dry sand. Two levels of loading were adopted to represent different service load conditions. The maximum number of loading cycles was 1,000. From the test results, it was found that the even though in the service load condition, the pile response was still affected by cyclic effects and a larger load level would produce more significant influence. In a global point of view, the lateral displacement and maximum moment increased with loading cycles, while the secant stiffness within a cycle decreased with cycles. The cyclic effect was more significant on the lateral displacement than on the moment. In a local point of view, cyclic loading would degrade the equivalent subgrade stiffness for the soil shallower than about seven times diameter. In addition, the secant subgrade stiffness within a cycle increased with loading cycles. Some experimental relationships of lateral pile response and loading cycles were built and compared with those in the literature.     

Torsional Dynamic Impedance of a Tapered Pile Considering its Construction Disturbance Effect

The dynamic response of a tapered pile (considering its construction disturbance effect) is investigated when the tapered pile is subjected to a time-harmonic torsional loading. For most engineering conditions, the surrounding soil may be weakened or strengthened owing to the construction disturbance effect of the tapered pile, resulting in the soil becoming radially inhomogeneous. In order to consider this problem, the circumferential shear complex stiffness transfer model is proposed to simulate the radial inhomogeneity of soil. Then, the governing equations of a tapered pile-soil system subjected to torsional dynamic loading are established. By virtue of the circumferential shear complex stiffness transfer method and the impedance function transfer method, the analytical solution of torsional dynamic impedance at the head of the tapered pile is derived. Based on the presented solution, the influence of the construction disturbance effect of the surrounding soil on the torsional dynamic impedance at the pile head is investigated within the low-frequency range concerned in the design of a dynamic foundation. The results show that, even if the hardening range and softening range of the surrounding soil vary within a smaller scale, the hardening effect and softening effect also have a notable influence on the torsional dynamic impedance at the pile head.     

Small- and large-scale model tests on the buckling property of slender pile

Slender piles embedded in soft ground or liquefied soil may buckle under vertical load. In this paper, both small- and large-scale model tests are conducted to investigate the buckling mechanisms of a slender pile and the lateral earth pressure acting on the pile. To observe the buckling of a slender pile, the strain-controlled loading method is adopted to apply a vertical load. When the two ends of a slender pile are hinged, the buckling mechanisms of small- and large-scale model tests are same. It should be noted that this applies only to a system with a small ratio of pile bending stiffness to soil bending stiffness. An applied vertical load increases with an increasing pile head settlement until it reaches the critical buckling load. By further increasing the pile head settlement, the measured load approaches the critical buckling load. In the large-scale model test, the measured lateral earth pressure (i.e., active and passive) acting on the slender pile varies linearly with the lateral pile displacement when the measured range is 3–5?m beneath the ground. A critical buckling calculation method has been adopted to compare with the conventional “m” method. The two-sided earth pressure calculation method can achieve more approximate results with the model test.