基础隔震单层偏心结构扭转地震反应分析

采用微分型滞回恢复力模型模拟隔震支座的恢复力特性，对基础隔震单层偏心结构的扭转地震反应进行分析，研究隔震系统偏心距和上部结构偏心距对结构扭转反应的影响。结果表明，采用隔震技术可以显著降低隔震结构的扭转地震反应。     

结构偏心对基础隔震结构地震反应的影响

本文对基础隔震偏心结构在不同场地上的地震动作用下的反应进行了深入研究，探讨了上部结构偏心、隔震层偏心、场地条件等因素对于基础隔震结构地震反应的影响，选取了能反映结构偏心特性的参数，以便将分析各因素对隔震结构地震反应的影响转化为分析参数的影响。通过大量的数值计算与分析，得到了一些对实际工程有意义的结论。     

层间隔震偏心结构双向地震耦合响应研究

建立双向地震作用下层间隔震双向偏心结构侧扭耦联分析模型;考虑上部结构及下部结构的弹塑性模型,隔震支座采用双向耦合非线性Bouc-wen模型模拟;分析偏心参数对层间隔震双向偏心结构的影响规律;评价双向地震作用下我国抗震规范给出的扭转影响系数静力预测值的准确性。结果表明,双向地震作用下设置中间柔性隔震层可以减小上\,下部结构扭转的耦连效应;下部结构存在双向偏心会对隔震层和下部结构扭转反应带来不利影响;LRB耦合效应对层间隔震地震响应影响较小;当下部结构偏心率较大时现行规范计算扭转系数偏于不安全。     

单轴平扭耦联基础隔震结构动力简化分析

为了建立单轴平扭耦联基础隔震结构的动力简化分析方法,探讨了影响结构扭转反应的参数取值规律,首先基于层单元模型,通过假定上部结构楼层回转半径、偏心距、弹力半径相等,推导了单轴平扭耦联基础隔震结构线性化的动力计算方程;其次,运用该简化分析方程,通过一算例进行了动力响应的参数分析。结果表明:调整隔震层刚心使其与上部结构质心位置接近,可显著降低偏心隔震结构扭转反应;增大隔震层刚度半径及阻尼半径可有效减少或抑制结构扭转反应;所建简化分析方程能有效模拟偏心隔震结构动力响应。     

上部结构与基础隔震层偏心对结构地震响应的影响

随着基础隔震技术的发展,我国在高烈度地区广泛开展基础隔震技术的工程应用必将成为一种趋势,但由于建筑功能和建筑造型的丰富多彩,结构的质量中心和刚度中心也趋于分布不均匀,以三层的钢框架结构为分析模型,利用结构分析软件Sap2000对上部结构质量中心和隔震层质量中心、刚度中心分布不均匀的三种方案进行单向水平地震作用下的非线性时程分析,分析结果表明:上部结构质量中心与隔震层质量中心存在偏心距对结构的扭转效应以及地震响应有较大的影响,减小上部结构的偏心距对调整结构的水平地震响应的影响成效最为显著;对于隔震层而言,隔震层的刚度中心偏心距较质量中心偏心距对上部结构的影响更大,有效控制隔震层刚度中心的偏心距在隔震设计中会更加有效。     

摩擦摆基础隔震上部偏心结构地震反应影响因素分析

对上部结构存在偏心的摩擦摆基础隔震结构进行了水平双向地震作用下的地震反应分析,研究了上部结构偏心距和抗扭刚度对结构地震反应的影响。分析表明:上部结构偏心距对上部结构和隔震层的位移反应和加速度反应均有较大影响,即使在上部结构偏心距较小时,其对结构地震反应仍有一定程度的影响;上部结构的抗扭刚度对上部结构的加速度反应影响较小,而对上部结构的位移反应影响较大;上部结构的抗扭刚度对隔震层的加速度反应和位移反应影响较小。因而,对于上部结构存在偏心的摩擦摆基础隔震结构,应减小上部结构偏心距并增大其抗扭刚度以减小摩擦摆基础隔震结构的扭转反应。     

多向地震作用下隔震配电建筑物的非线性动力反应分析

本文结合我国首例将隔震技术应用于变电建筑物的工程———西安市330kV西北郊变电站110kV配电楼工程,研究隔震结构在多向地震作用下的非线性动力反应,并把计算结果与单向地震作用的结果进行分析比较。结果表明,本工程采用隔震技术是可行的,采用基础隔震措施可有效地控制结构的偏心扭转效应,使屋面层及楼面层的运动规律趋于一致,建筑物整体趋于平动,同时还可显著降低上部结构及电气设备的地震作用,并且在多向地震作用下的结果比单向地震作用时的隔震效果更加合理。目前该工程已竣工投产,本文工作将为隔震技术在电力系统的更广泛应用打下一个良好的基础。     

单轴偏心的单层隔震框架结构地震扭转反应分析

建立了单轴偏心的单层基础隔震结构的运动方程,计算了在不同偏心率情况下结构匠地震反应,结果表明：对于存在扭转变形的结构来说,随着结构偏心率的增大,基础隔震的效率降低。     

平扭耦联隔震体系隔震支座阻尼分布影响分析

为了研究铅芯橡胶隔震支座的阻尼分布对平扭耦联隔震体系隔震效果的影响,本文对一个三层两跨钢框架,通过调整上部结构负重块位置及下部铅芯橡胶隔震支座的分布位置,进行不同偏心工况下平扭耦联隔震体系地震模拟振动台试验,获得了不同偏心工况、不同阻尼分布情况下结构位移和加速度的时程曲线。试验和分析表明:隔震层阻尼中心与上部结构的质心位置接近,或者增大隔震层的阻尼半径,可显著地降低上部结构的扭转反应。     

高层隔震结构扭转分析

为研究高层隔震结构在地震作用下的扭转效应,用Etabs软件建立1个高层抗震结构和4个具有不同扭转特性的高层隔震结构的空间模型进行地震响应分析,以验证此原则上部结构质量中心与隔震层刚度中心的重合与否对结构扭转效应的影响程度,而后考察偏心高层隔震结构在偶然偏心地震作用下结构的扭转效应。结果表明:由于地震作用的减小,扭转效应要远小于原抗震结构,且隔震本身对于结构扭转效应的抑制效果要好于上述原则;扭转效应的减震率大于平动效应的减震率。布置在隔震层平面外围的铅芯橡胶隔震支座对隔震层的扭转有一定的控制作用。     

Shake table tests on a mass eccentric model with base isolation

A mass eccentric structure is usually more seismically vulnerable than its concentric counterpart because of the coupled torsional–translational response of such structures. In this work, dynamic characteristics and response of a five‐storey benchmark model with moderate mass eccentricity were investigated using a shake table, simulating four different ground motions. The effectiveness of laminated rubber bearings (LRB) and lead‐core rubber bearings (LCRB) in protecting eccentric structures was examined and evaluated in relation to translational and torsional responses of the benchmark model. It was observed that both translational and torsional responses were significantly reduced with the addition of either a LRB or LCRB isolated system regardless of the nature of ground motion input. The LRB were identified to be more effective than LCRB in reducing model relative displacements, the relative torsional angle as well as accelerations, and therefore provided a better protection of the superstructure and its contents. On the other hand, LCRB rendered a smaller torsional angle and absolute displacement of the base isolation system, hence a more stable structural system. Copyright © 2003 John Wiley & Sons, Ltd.     

建筑物偏心结构对其抗震性能的影响

偏心对建筑物的抗震效果有很大的影响。在对三种常见建筑物框架结构在偏心扭矩作用下的受震反应进行数值模拟时,采用6层建筑物模型,通过三维非线性模拟偏心结构对建筑物抗震性能影响的分析,采用最大层间位移作为衡量标准,绘制易损曲线来进行结果分析。结果显示:若忽略意外扭矩的影响,可能会高估钢结构体系的抗震性能,而影响安全评估结果;如果采用全层5%质量偏心来考虑意外偏心扭矩的话,会低估钢结构建筑物的抗震性能。     

Analytical and experimental studies on midstory isolated buildings with modal coupling effect

In a midstory isolated building, the isolation system is incorporated into the midstory rather than the base of the building. Because of the flexibility of the substructure below the isolation system in a midstory isolated building, the contribution of higher modes to the seismic responses of the midstory isolated structure may not be negligible, especially when the coupling of higher modes exists. To investigate this modal coupling effect, a simplified three‐lumped‐mass structural model of the midstory isolated building is assumed in this study. Through the equivalent linear analysis and shaking table tests, it is found that the coupling of higher modes may lead to enlarged acceleration responses at the super‐floor and superstructure above the isolation layer. Accordingly, a simple method to prevent the midstory isolation design from the coupling of higher modes attributed to the improper design of the substructure and superstructure is proposed in this paper. Copyright © 2012 John Wiley & Sons, Ltd.     

地震作用下钢框架高层结构的抗震性能研究

钢框架高层建筑结构是当前高层建筑设计中使用最为广泛的技术,为提升其抗震性能,本文研究将调谐质量阻尼器安装在钢框架高层建筑结构顶部,考虑到建筑空间需求、防止集中荷载和提升控制效果等因素,在相同楼层或同顶部接近楼层中设置数个较小的、频率一致的子控制装置,通过设置调谐质量阻尼器受控结构等效阻尼比求极值的方法,获取最优刚度与最优阻尼系数;将获取的结果在有限元软件中进行模态分析获取模态质量,实现钢框架高层建筑结构扭转振动的减振控制。实验结果表明,地震荷载下,该方法使得建筑结构顶层角位移峰值和角加速度峰值分别降低50%和30%左右,建筑结构响应下降19%～26%,提高了高层建筑结构的稳定性。     

不对称大底板多塔楼隔震结构的地震响应分析

针对不对称大底板多塔楼隔震结构体系,通过建立地震响应的动力分析简化模型,推导出不对称大底板多塔楼隔震结构体系地震作用下的运动方程。对一实际的不对称大底板多塔楼隔震结构进行地震响应仿真分析,探讨塔楼质量偏心率和塔楼质量比对结构周期比、位移比和层剪力比的影响。结果显示,不对称大底板多塔楼隔震结构扭转角主要由隔震层产生;与不隔震结构相比,不对称大底板多塔楼隔震体系的扭转角减小,可取得较好的减震效果;塔楼与底板的位置分布和质量分布会影响体系的扭转效应和减震效果,应尽量使塔楼的质心与底板质心重合,塔楼质量分布均匀,以减小结构的扭转效应,提高减震效果。     

Accidental torsion due to overturning in nominally symmetric structures isolated with the FPS

Overturning of a structure causes variations in the normal loads of the isolators supporting that structure. For frictional isolators, such variation leads to changes in the frictional forces developed and, hence, in the strength distribution in plan. For frictional pendulum system (FPS) isolators, it also causes changes in the pendular action, i.e. in the stiffness distribution of the isolation interface. Therefore, although the structure is nominally symmetric it develops lateral–torsional coupling when it is subjected to two horizontal components of ground motion. This coupling is denoted herein as accidental torsion due to overturning, and its effect in the earthquake response of nominally symmetric structures is evaluated. Several parameters are identified to control this coupling, but the most important are the slenderness of the structure and the aspect ratio of the building plan. Results are presented in terms of the torsional amplification of the deformations of the isolation base and the interstorey deformations of the superstructure. The FPS system is modelled accurately by including true large deformations and the potential uplift and impact of the isolators. Impulsive as well as subduction‐type ground motions are considered in the analysis, but results show small differences between them. An upper bound for the mean‐plus‐one standard deviation values of the torsional amplifications for the base due to this accidental torsion is 5%. This implies that for design purposes of the isolation system such increase in deformations could probably be neglected. However, the same amplification for the interstorey deformations may be as large as 50%, depending on the torsional stiffness and slenderness of the superstructure, and should be considered in design. In general, such amplification of deformations decreases for torsionally stiffer structures and smaller height‐to‐base aspect ratios. Copyright © 2003 John Wiley & Sons, Ltd.