Numerical study on the interaction among a nonlinear wave,composite breakwater and sandy seabed

Most previous investigations related to composite breakwaters have focused on the wave forces acting on the structure itself from a hydrodynamic aspect. The foundational aspects of a composite breakwater under wave-induced cyclic loading are also important in studying the stability of a composite breakwater. In this study, numerical simulations were performed to investigate the wave-induced pore water pressure and flow changes inside the rubble mound of the composite breakwater and seabed foundation. The validity and applicability of the numerical model were demonstrated by comparing numerical results with existing experimental data. Moreover, the present model clearly has shown that the instantaneous directions of pore water flow motion inside the seabed induced by surface waves are in good agreement with the general wave-induced pore water flow inside the seabed. The model is further used to discuss the stability of a composite breakwater, i.e., the interaction among nonlinear waves, composite breakwater and seabed. Numerical results suggest that the stability of a composite breakwater is affected by not only downward shear flow generating on the seaward slope face of the rubble mound but, also, a high and dense pore water pressure gradient inside the rubble mound and seabed foundation.     

Wave interaction with a concentric porous cylinder system

This is a theoretical investigation of wave interaction with a concentric surface-piercing two-cylinder system. The exterior cylinder is porous and considered to be thin in thickness and the interior cylinder is impermeable. Both cylinders are rigidly fixed at the sea bed. The fluid motion is idealized as a linearized potential flow. The free-surface elevation and the total net hydrodynamic forces acting on both cylinders are determined analytically. The wave-induced overturning moments are also evaluated. It is found that, with the existence of the exterior porous cylinder, the hydrodynamic force acting on the interior cylinder is reduced if compared to the force exerted on the interior cylinder by a direct wave impact. The reduction of the wave amplitude around the leeward side of the outer porous cylinder is shown from the free-surface computations. In this paper, results are also presented to illustrate the effects of wave parameter and structural porosity on this wave and cylinder interaction problem. The role played by the ratio of radii of the inner and outer cylinders is duscussed.     

Computation of wave-making resistance of a catamaran in deep water using a potential-based panel method

This paper presents a potential-based boundary element method for solving a nonlinear free-surface flow problem for a Wigley catamaran moving with a uniform speed in deep water. Since the interior flow of each monohull of the catamaran is different from the exterior flow, both monohulls must be considered as lifting bodies. The pressure Kutta condition is imposed at the trailing-edge of the lifting body by determining the dipole distribution, which generates required circulation on the lifting part. The effects of wave interference and hull separation on the hydrodynamic characteristics of the catamaran hull are analyzed and the validity of the computer scheme is examined by comparing the wave resistance with the numerical results of others. The present method could be a useful design tool for screening the suitable combinations of hull parameters and hull spacing at the preliminary design stage of catamaran hull.     

Simplified analytical solutions for wave interaction with absorbing-type caisson breakwaters

Simplified analytical solutions are presented to model the interaction of linear waves with absorbing-type caisson breakwaters, which possess one, or two, perforated or slotted front faces which result in one, or two, interior fluid regions (chambers). The perforated/slotted surfaces are idealized as thin porous plates. Energy dissipation in the interior fluid region(s) inside the breakwater is modelled through a damping function. Under the assumption of potential flow and linear wave theory a boundary-value problem may then be formulated to describe wave interaction with the idealized structure. A solution to this simplified problem may be obtained by an eigenfunction expansion technique and an explicit analytical expression may be obtained for the reflected wave height. Using the experimental work of previous authors, damping coefficients are determined for both single and double chamber absorbing-type caisson breakwaters. Based on the damping for a single perforated-wall breakwater, a methodology is proposed to enable the estimation of the damping coefficients for a breakwater with two chambers. The theoretical predictions of the reflection coefficients for the two-chamber structures using the present model are compared with those obtained from laboratory experiments by other authors. It is found that the inclusion of the damping in the interior fluid region gives rise to improved agreement between theory and experiment.     

Wave interaction with a wave absorbing double curtain-wall breakwater

This study examines the hydrodynamic performance of a wave absorbing double curtain-wall breakwater. The breakwater consists of a seaward perforated wall and a shoreward impermeable wall. Both walls extend from above the seawater to some distance above the seabed. Then the below gap allows the seawater exchange, the sediment transport and the fish passage. By means of the eigenfunction expansion method and a least square approach, a linear analytical solution is developed for the interaction of water waves with the breakwater. Then the reflection coefficient, the transmission coefficient and the wave forces acting on the walls are calculated. The numerical results obtained for limiting cases agree very well with previous predictions for a single partially immersed impermeable wall, the double partially immersed impermeable walls and the bottom-standing Jarlan-type breakwater. The predicted reflection coefficients for the present breakwater also agree reasonable with previous experimental results. Numerical results show that with appropriate structure parameters, the reflection and transmission coefficients of the breakwater may be both below 0.5 at a wide range of the relative water depth. At the same time, the magnitude of wave force acting on each wall is small. This is significant for practical engineering.     

Hydrodynamic characteristics of semi-immersed breakwater with an attached porous plate

In the present study, wave interaction with a fixed, partially immersed breakwater of box type with a plate attached (impermeable-permeable) at the front part of the structure is investigated numerically and experimentally. The large scale laboratory experiments on the interaction of regular waves with the special breakwater were conducted in the wave flume of Laboratori d’Enginyeria Marνtima (LIM) at Universitat Politecnica de Catalunya (UPC) in Barcelona. Experimental results are compared with numerical results obtained with the use of the Cornell breaking Wave and Structures (COBRAS) wave model. The effects of an impermeable as well as a permeable plate attached to the bottom of the breakwater on its hydrodynamic characteristics (wave transmission, reflection, dissipation, velocity and turbulence kinetic energy) are investigated. Computed velocities and turbulence kinetic energy in the vicinity of the structure indicate the effects of the breakwater with the attached (impermeable/permeable) plate on the flow pattern and the turbulence structure. The attached impermeable plate at the front part of the breakwater enhances significantly the efficiency of the structure in attenuating the incident waves. The permeable plate reduces the efficiency of the structure since wave energy is transmitted through the porous body of the plate. Based on the hydrodynamic characteristics it is inferred that the breakwater with an impermeable plate attached to its bottom is more efficient. The comparison of horizontal and vertical forces acting on the breakwater for all cases examined reveals that plate porosity influences slightly vertical force and severely horizontal force acting on the structure, reducing maximum values in both cases.     

Short-crested waves interaction with a concentric porous cylinder system with partially porous outer cylinder

In this paper, based on the linear wave theory, the interaction of short-crested waves with a concentric dual cylindrical system with a partially porous outer cylinder is studied by using the scaled boundary finite element method (SBFEM), which is a novel semi-analytical method with the advantages of combining the finite element method (FEM) with the boundary element method (BEM). The whole solution domain is divided into one unbounded sub-domain and one bounded sub-domain by the exterior cylinder. By weakening the governing differential equation in the circumferential direction, the SBFEM equations for both domains can be solved analytically in the radial direction. Only the boundary on the circumference of the exterior porous cylinder is discretized with curved surface finite elements. Meanwhile, by introducing a variable porous-effect parameter G, non-homogeneous materials caused by the complex configuration of the exterior cylinder are modeled without additional efforts. Comparisons clearly demonstrate the excellent accuracy and computational efficiency associated with the present SBFEM. The effects of the wide range wave parameters and the structure configuration are examined. This parametric study will help determine the various hydrodynamic effects of the concentric porous cylindrical structure.     

波浪与外壁透空双方形沉箱相互作用

在线性波浪理论下,利用复合边界元素法(composite BEM)数值解析在等水深、规则波浪入射二种外壁透空双方形沉箱的无因次波力及Kd绕射分布图,并分别与其他研究者所作双圆筒内、外圆柱无因次波力及绕射分布图的计算结果进行比较,都说明本模式的合理性和可行性。在考虑不同透水参数下,分别计算波浪作用在内、外结构物的波力及沉箱四周绕射系数大小分布图。计算结果显示:波浪作用于外壁透空全透水双方形沉箱,外方柱无因次最大波力值会随着透水参数增加而降低;内方柱无因次最大波力值则随着透水参数增加而增加。本研究结果可供设计外海透水方形沉箱结构交互作用参考。     

Water wave interaction with an array of bottom-mounted surface-piercing porous cylinders

The interaction of water waves with arrays of bottom-mounted, surface-piercing circular cylinders is investigated theoretically. The sidewall of each cylinder is porous and thin. Under the assumptions of potential flow and linear wave theory, a semi-analytical solution is obtained by an eigenfunction expansion approach first proposed for impermeable cylinders by Spring and Monkmeyer (1974), and later simplified by Linton and Evans (1990). Analytical expressions are developed for the wave motion in the exterior and all interior fluid regions. Numerical results are presented which illustrate the effects of various wave and structural parameters on the hydrodynamic loads and the diffracted wave field. It is found that the porosity of the structures may result in a significant reduction in both the hydrodynamic loads experienced by the cylinders and the associated wave runup.     

Wave motion over a submerged breakwater with an upper horizontal porous plate and a lower horizontal solid plate

This study examines the hydrodynamic performance of a modified two-layer horizontal-plate breakwater. The breakwater consists of an upper submerged horizontal porous plate and a lower submerged horizontal solid plate. By means of the matched eigenfunction expansion method, a linear analytical solution is developed for the interaction of water waves with the structure. Then the reflection coefficient, the transmission coefficient, the energy-loss coefficient and the wave forces acting on the plates are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a single submerged horizontal solid plate and a single submerged horizontal porous plate. Numerical results show that with a suitable geometrical porosity of the upper plate, the uplift wave forces on both plates can be controlled at a low level. Numerical results also show that the transmission coefficient will be always small if the dimensionless plate length (plate length versus incident wavelength) exceeds a certain moderate value. This is rather significant for practical engineering, as the incident wavelength varies over a wide range in practice. Moreover, it is found that the hydrodynamic performance of the present structure may be further enhanced if the lower plate is also perforated.     

Dual pontoon floating breakwater

The hydrodynamic properties of a dual pontoon floating breakwater consisting of a pair of floating cylinders of rectangular section, connected by a rigid deck, is investigated theoretically. The structure is partially restrained by linear symmetric moorings fore and aft. The fluid motion is idealized as linearized, two-dimensional potential flow and the equation of motion of the breakwater is taken to be that of a two-dimensional rigid body undergoing surge, heave and pitch motions. The solution for the fluid motion is obtained by the boundary integral equation method using an appropriate Green's function. Numerical results are presented which illustrate the effects of the various wave and structural parameters on the efficiency of the breakwater as a barrier to wave action. It is found that the wave reflection properties of the structure depend strongly on the width, draft and spacing of the pontoons and the mooring line stiffness, while the excess buoyancy of the system is of lesser importance.     

Numerical investigation on the dynamics of a vertical wall defenced by an offshore breakwater

The numerical and experimental investigations on the performance of an offshore-submerged breakwater in reducing the wave forces and wave run-up on vertical wall are presented. A two-dimensional finite-element model is employed to study the hydrodynamic performance of the submerged breakwater under the action of regular and random waves. The numerical prediction has been supported with experimental measurements. The wave forces and wave run-up on the vertical wall were measured for different breakwater configurations. The applicability of linear theoretical model in the prediction of wave forces on the wall by a submerged breakwater has been discussed.     

半潮堤前的反射形态与时均流速场分析

采用模型试验和数值模拟研究了不同水深工况下半潮堤前的反射形态及时均流速场。基于Hilbert变换建立了叠合波的时频分离技术,同时获取了入射波和反射波的波面过程及相位关系,通过试验数据证明其适用于不同反射程度的波浪信号分析。不同水深工况下,半潮堤前形成了部分立波系统,腹点和节点分别以四分之一波长的偶数倍和奇数倍交替增加。半潮堤前底床水质点水平速度包络图与波面包络图相差四分之一周期的相位,水平速度的极大值和极小值分别出现在波面包络图的节点和腹点,意味着节点处易形成冲刷,腹点处易形成淤积。3种工况的周期平均速度场均在迎浪基床上方的堤脚处存在一个小型环流系统,可能引起局部冲刷,此处需加强防护。淹没工况下,半潮堤前的周期平均速度场形成一个大型环流系统,表层水流向堤后,中下层水流向海侧,意味着底床悬起的泥沙很可能向离岸方向流失。     

基于粘性流模型的筒型基础防波堤波浪力数值分析

筒型基础防波堤是一种新型港口海岸工程结构,其基础上部是由连续排列的圆筒构成的直立防浪墙.采用粘性流数值模型,研究连续圆筒防波堤上波浪力竖向分布、水平(沿圆筒环向)分布和波浪力合力特性,并对粘性流数值模型计算的平面直墙波浪力与海港水文规范方法计算结果;粘性流数值模型计算的连续圆筒墙面波浪力与平面直墙波浪力;无限长连续圆筒墙面波浪力与有限长连续圆筒墙面波浪力进行比较分析.针对所选工程算例,建议按<海港水文规范>中平面直墙波浪力计算方法确定连续圆筒防波堤上的波浪力时,波峰时考虑0.90左右的折减系数,波谷时考虑0.95左右的折减系数.     

Added mass and damping of a vertical cylinder in finite-depth waters

A comprehensive set of theoretical added masses and wave damping data for a floating circular cylinder in finite-depth water is presented. The hydrodynamic problem is solved by matching eigen functions of the interior and exterior problems. The resulting infinite system is solved directly and found to have excellent truncation characteristics. Added mass and damping are given for heave, sway, and roll motion, as well as coupling coefficients for sway and roll. It is shown that the heave added mass is logarithmic singular and the damping approaches a constant in the low-frequency limit. Transition of the behaviour in finite-depth water to deep water is also discussed.     

Wave diffraction through submerged flexible breakwaters

This paper presents an analytical, computationally efficient method for the wave reflection and dynamic displacement of a submerged flexible breakwater. The solution of the two-dimensional linearized hydrodynamic problem introduced is based on the eigenfunction expansion technique. The breakwater is assumed to be thin, impermeable, flexible, moored to the bed through tethers and kept in tension by means of a floating buoy at its tip. The beam structure is considered to be either clamped or hinged at the sea bed, situated in an arbitrary water depth and subjected to normal linear waves. Numerical examples presented by this method are compared with those obtained by the Boundary Integral Equation Method, presented by Williams et al. Comparisons show an excellent agreement over a wide range of parameters for the wave reflection and the dynamic displacement. Numerical results are presented, mainly to show the effect of the breakwater rigidity and the method of fixation on the wave reflection and the structural displacement over a wide range of wave frequencies.     

弧板式透空堤消浪性能影响因素数值研究

弧板式透空堤是由弧型板组成的新型防波堤结构。为探讨其透射系数的影响因素,利用Fluent软件基于N-S方程构建了波浪与板式透空堤相互作用的数值模型,讨论了相对潜深、入射波周期、相对波高、相对板宽和结构型式对透射系数的影响。结果表明:弧板式透空堤的透射系数随着相对波高和入射波周期的增大而增大,在静水面附近透射系数最小,尤以静水面和略高于静水面时的消浪效果最佳;在相同波浪要素条件下,静水面及其上0.02 m和0.04 m位置处,弧板式透空堤的消浪效果明显优于平板式透空堤。     

Hydrodynamic performance of a pile-supported OWC breakwater: An analytical study

A pile-supported OWC breakwater is a novel marine structure in which an oscillating water column (OWC) is integrated into a pile-supported breakwater, with a dual function: generating carbon-free energy and providing shelter for port activities by limiting wave transmission. In this work we investigate the hydrodynamics of this novel structure by means of an analytical model based on linear wave theory and matched eigenfunction expansion method. A local increase in the back-wall draft is adopted as an effective strategy to enhance wave power extraction and reduce wave transmission. The effects of chamber breadth, wall draft and air chamber volume on the hydrodynamic performance are examined in detail. We find that optimizing power take-off (PTO) damping for maximum power leads to both satisfactory power extraction and wave transmission, whereas optimizing for minimum wave transmission penalizes power extraction excessively; the former is, therefore, preferable. An appropriate large enough air chamber volume can enhance the bandwidth of high extraction efficiency through the air compressibility effect, with minimum repercussions for wave transmission. Meanwhile, the air chamber volume is found to be not large enough for the air compressibility effect to be relevant at engineering scales. Finally, a two-level practical optimization strategy on PTO damping is adopted. We prove that this strategy yields similar wave power extraction and wave transmission as the ideal optimization approach.     

柔性水囊潜堤消波特性的溃坝水槽试验研究

柔性水囊潜堤由橡胶制成,内部充水,具有结构简单、造价低廉等优点,能较好满足人工岛、跨海桥梁、海洋平台等基础设施建设工程对简单便携、拆装方便的临时防波堤的需求。为了探究柔性水囊潜堤的消波特性,在溃坝水槽内开展溃坝波与半圆柱形柔性水囊潜堤相互作用的试验研究,重点探究柔性水囊潜堤与溃坝波相互作用过程中水位变化特性,并与半圆柱刚性潜堤的性能进行比较;同时分析柔性水囊潜堤内部初始水压和浸没深度等参数对其消波性能的影响。结果表明：柔性水囊潜堤能够用作临时防波堤来衰减波浪;与半圆柱刚性潜堤相比,柔性水囊潜堤在降低溃坝波无量纲最大水位、提高消波性能方面更具优势;内部初始水压是影响柔性水囊潜堤消波性能的重要因素,适当降低内部初始水压,有利于增强柔性潜堤的变形程度,进而增加波能耗散,可获得更好的消波效果;而增加浸没深度即潜深,会使得柔性水囊潜堤对溃坝波的影响程度降低,消波效果减弱。     

2-D numerical analysis of near-field flow at low-crested permeable breakwaters

This paper describes the capability of a numerical model named COrnell BReaking waves And Structures (COBRAS) [Lin, P., Liu, P.L.-F., 1998. A numerical study of breaking waves in the surf zone. Journal of Fluid Mechanics 359, 239–264; Liu, P.L.-F., Lin, P., Chang, K.A., Sakakiyama, T., 1999. Numerical modeling of wave interaction with porous structures. Journal of Waterway, Port, Coastal and Ocean Engineering 125, 322–330, Liu, P.L.-F., Lin, P., Hsu, T., Chang, K., Losada, I.J., Vidal, C., Sakakiyama, T., 2000. A Reynolds averaged Navier–Stokes equation model for nonlinear water wave and structure interactions. Proc. Coastal Structures '99, 169–174] based on the Reynolds Averaged Navier–Stokes (RANS) equations to simulate the most relevant hydrodynamic near-field processes that take place in the interaction between waves and low-crested breakwaters. The model considers wave reflection, transmission, overtopping and breaking due to transient nonlinear waves including turbulence in the fluid domain and in the permeable regions for any kind of geometry and number of layers. Small-scale laboratory tests were conducted in order to validate the model, with different wave conditions and breakwater configurations. In the present study, regular waves of different heights and periods impinging on a wide-crested structure are considered. Three different water depths were tested in order to examine the influence of the structure freeboard. The experimental set-up includes a flow recirculation system aimed at preventing water piling-up at the lee of the breakwater due to overtopping. The applicability and validity of the model are examined by comparing the results of the numerical computations with experimental data. The model is proved to simulate with a high degree of agreement all the studied magnitudes, free surface displacement, pressure inside the porous structure and velocity field. The results obtained show that this model represents a substantial improvement in the numerical modelling of low-crested structures (LCS) since it includes many processes neglected previously by existing models. The information provided by the model can be useful to analyse structure functionality, structure stability, scour and many other hydrodynamic processes of interest.