确定海洋平台钢裂纹扩展曲线的快速方法

提出了一种确定海洋平台钢裂纹扩展曲线的快速方法。该方法可以综合利用以往的经验数据和当前试验数据确定表面疲劳裂纹扩展速率曲线。与传统的只能利用当前试验数据确定表面疲劳裂纹扩展速率曲线相比。其可利用信息量大幅度增加,所以在精度相同的情况下,可以节省大量试件;而且在试样数一定的情况下。又可大大提高预测精度。文中还给出了海洋平台钢试验对比实例。     

基于EIFS和P-M的海底管道腐蚀疲劳寿命预测

鉴于腐蚀疲劳损伤的特殊性,研究了点蚀过程和腐蚀疲劳裂纹扩展过程。基于等效初始缺陷尺寸(EIFS)和线性累积损伤理论(P-M)方法,消除了点蚀形核、蚀坑生长及腐蚀疲劳短裂纹扩展对腐蚀疲劳寿命预测的影响;避免了基于单点蚀坑建立的腐蚀疲劳寿命预测表达式的弊端;合理地简化了随机荷载下腐蚀疲劳寿命的预测流程。利用现有试验数据,对基于EIFS和P-M方法建立的腐蚀疲劳寿命预测表达式进行了模型验证。结果显示,所提模型的有效性和合理性得到了验证,为工程实际中海底管道的腐蚀疲劳寿命预测提供了一种可行方法。     

海洋平台E36-Z35钢表面疲劳裂纹扩展速率的蒙特卡洛模拟

本文利用蒙特卡洛法模拟分析海洋平台Ｅ３６Ｚ３５钢表面疲劳裂纹扩展速率,并确定了算式中的参数分布规律及相关性。通过计算数据与试验数据的对比分析,表明蒙特卡洛法模拟结果合理、可靠。     

深水半潜式平台结构关键节点疲劳破坏机理试验研究

深水半潜式平台结构在深海环境荷载及作业动荷载的作用下容易产生疲劳损伤累积,加速疲劳裂纹扩展,导致结构发生疲劳破坏。对深水半潜式平台横撑部位的两类关键节点进行了疲劳试验研究,分析了关键节点的疲劳破坏现象、疲劳破坏过程以及疲劳裂纹扩展规律。试验结果表明:应用规范给出的裂纹扩展模型和参数估算关键节点的疲劳寿命低于试验所得的疲劳寿命,说明应用规范给出的裂纹扩展模型和参数估算节点的疲劳寿命比较安全;根据疲劳试验结果建立的关键节点的S-N曲线参数与DNV规范给出的较为吻合;关键节点焊趾处的ε-N关系曲线可以反映出关键节点疲劳破坏的三个阶段破坏规律。研究结果为有效地预测平台结构关键节点的疲劳损伤程度,及时进行维修加固延长结构的使用寿命提供参考。     

老龄半潜式钻井平台节点疲劳裂纹扩展寿命预报

通过结合常规谱疲劳分析方法和裂纹扩展分析方法,给出了一种工程实用的评价老龄平台节点裂纹扩展寿命的方法,并以某一平台为例进行了验证计算。首先,基于谱疲劳分析得到各个节点在过去30年的节点疲劳损伤,然后,对损伤接近或大于1.0的节点进行基于单一曲线模型的裂纹扩展分析,以求得该节点在目前状态下裂纹扩展寿命。结果表明,目标平台计算疲劳热点满足继续使用的要求。此外,针对不同初始裂纹尺寸时的裂纹扩展寿命计算结果表明初始裂纹尺寸对疲劳裂纹扩展寿命影响很大。     

随机载荷作用下平台结构疲劳寿命预测

海洋等工程结构物在服役过程中的受载历程是一个随机过程。研究裂纹在谱载荷作用下的扩展规律对可靠预报平台等结构物的疲劳寿命具有十分重要的意义。提出了一个由应力比和裂纹尖端约束及塑性区尺寸为主要参数计算裂纹张开比,来考查载荷相互作用下疲劳裂纹扩展寿命的计算模型。用该模型对几种谱载荷作用下疲劳实验结果进行了预测,将预测结果与不考虑裂纹闭合的线性损伤模型及疲劳计算程序FASTRAN的预测结果进行了比较,表明本模型能较好地预测谱载荷作用下的疲劳裂纹扩展。     

极端循环载荷下船体裂纹箱型梁的极限强度

旨在了解箱型梁在极端循环载荷下的极限强度特性。利用非线性有限元方法来研究裂纹箱型梁的极限弯矩,分析了5种裂纹模型,探讨了裂纹类型、裂纹位置和裂纹长度的影响。考虑了两种载荷形式应用生死单元法对双向循环弯曲下裂纹扩展进行了模拟;并将由循环载荷引起的累积塑性损伤和疲劳裂纹损伤均考虑在内。无论单向循环还是双向循环,单裂纹模型的极限弯矩均小于双裂纹模型的极限弯矩;单边裂纹是最危险的裂纹类型。进一步分析了极端循环载荷下裂纹箱型梁的极限强度折减机理,得出了极限强度折减归因于这两种损伤的耦合作用的结论,并通过其他箱型梁验证了其适用性。     

海洋工程用钢的耐蚀性研究

自1951年美国海洋钢“mariner”(NiCuP)问世以来,采用整体长尺试样进行实海试验的方法,引起了各国海洋钢研制者的注意和重视。近几年来,我国海洋钢研制者也成功地进行了长尺试验,并在此基础上进行了电连接模拟海洋腐蚀试验方法的研究。     

焊接钢接头的海水腐蚀疲劳试验研究

本工作进行了板状焊接钢接头在空气中的常幅疲劳试验;和在海水中的常幅腐蚀疲劳试验(加载频率为0.2Hz,应力比 R=-1,海水温度～20℃,阴极保护负电位～850mV,SCE)。将两者试验结果比较,初步表明,钢接头海水腐蚀疲劳的平均寿命约为空气中的1/2到1/3。本工作还进行了焊缝经过 TIG 熔修的试件的试验,初步结果表明,TIG 熔修处理明显地增加了焊接接头的海水腐蚀疲劳(有阴极保护)寿命.     

随机变幅载荷下焊接接头的海水腐蚀疲劳研究

海上平台经受的波浪力作用是随机变幅循环载荷,本工作采用板状焊接接头模拟管节点热点焊趾处的受力状态,并模拟实际海洋环境与加载条件,海水温度为20℃循环流动,阴极保护电位为-850mV.(SCF),加载频率为0.2Hz,应力比为-1,进行随机变幅载荷下的海水腐蚀疲劳试验,试验结果与常幅载荷下的腐蚀疲劳寿命作了比较。本文利用线性累积损伤Miner法则,以随机变幅加载下的腐蚀疲劳寿命进行了估算,结果表明,估算的寿命与试验数据很接近,效果令人满意。     

Monte-Carlo Simulation of Surface Crack Growth Rate for Offshore Structural Steel E36 Z35

—The Monte-Carlo method is used to simulate the surface fatigue crack growth rate foroffshore structural steel E36-Z35,and to determine the distributions and relevance of the parameters in theParis equation.By this method,the time and cost of fatigue crack propagation testing can be reduced.Theapplication of the method is demonstrated by use of four sets of fatigue crack propagation data foroffshore structural steel E36-Z35.A comparison of the test data with the theoretical prediction for surfacecrack growth rate shows the application of the simulation method to the fatigue crack propagation tests issuccessful.     

Ice Induced Low Temperature Fatigue Crack Propagation in Offshore Structural Steel A131

To investigate the low temperature fatigue crack propagation behavior of offshore structuralsteel A131 under random ice loading,three ice failure modes that are commonly present in the Bohai Gulfare simulated according to the vibration stress responses induced by real ice loading.The test data are pro-cessed by a universal software FCPUSL developed on the basis of the theory of fatigue crack propagationand statistics.The fundamental parameter controlling the fatigue crack propagation induced by randomice loading is determined to be the amplitude root mean square stress intensity factor K_(arm).The test resultsare presented on the crack propagation diagram where the crack growth rate da/dN is described as thefunction of K_(arm).It is evident that the ice failure modes have great influence on the fatigue crack propaga-tion behavior of the steel in ice-induced vibration.However,some of the experimental phenomena and testresults are hard to be physically explained at present.The work in this paper is an init     

焊接节点低温疲劳试验与低温主S-N曲线的构建

为了拓展主S-N曲线法,使之更好地适用于低温、极地环境下船舶与海洋工程结构物的疲劳评估,进行了EH36材料T型焊接接头的低温疲劳性能试验,收集了国内外多个焊接节点低温疲劳数据,建立了疲劳试验试件的有限元模型,运用等效结构应力法,计算焊接节点的等效结构应力,构建低温环境下焊接节点的主S-N曲线。使用该曲线,预测低温疲劳试验的寿命,并与疲劳试验结果、常温主S-N曲线、常温中值D曲线的预测结果进行了比较,结果表明,所提低温主S-N曲线预测方法具有较高精度,可用于低温环境下船舶与海洋结构物疲劳寿命的预测。     

Fatigue Crack Propagation in Steel A131 Under Ice Loading of Crushing,Bending and Buckling

Three types of ice loading, which are most commonly present when ice acts on structures, are chosen and simulated for use of fatigue crack propagation tests on offshore structural steel A131. The three types of ice categorized in accordance with the failure modes when acting on structures called crushing ice, bending ice, and buckling ice, respectively. This paper presents an experimental investigation on the fatigue crack propagation behavior of widely used high strength steel A131 for offshore jackets in the loading environment of ice crushing, bending, and buckling. The test results of fatigue crack propagation in steel A131 under these simulated ice loading at temperature 292K. are presented and analyzed in detail in this paper. The amplitude root mean square stress intensity factor is optimized to be the fundamental parameter of fatigue crack propagation for all types of ice loading histories. The results are also compared with constant amplitude fatigue crack propagation conclusions as in wave loa     

A Global Refiability Assessment Method on Aging Offshore Platforms with Corrosion and Cracks

Corrosion and fatigue cracks are major threats to the structural integrity of aging offshore platforms.For the rational estimation of the safety levels of aging platforms,a global reliability assessment approach for aging offshore platforms with corrosion and fatigue cracks is presented in this paper.The base shear capacity is taken as the global ultimate strength of the offshore plaffoms,it is modeled as a random process that decreases with time in the presence of corrosion and fatigue crack propagation.And the corrosion and fatigue crack growth rates in the main members and key joints are modeled as random variables.A simulation method of the extreme wave loads which are applied to the structures of offshore platforms is proposed too.Furthermore,the statistics of global base shear capacity and extreme wave loads are obtained by Monte Carlo simulation method.On the basis of the limit state equation of global failure mode,the instantaneous reliability and time dependent reliability assessment methods are both presented in this paper.Finally the instantaueous reliability index and time dependent failure probability of a jacket platform are estimated with different ages in the demonstration example.     

A Probabilistic Model for Fatigue Crack Propagation Analysis

A simple probabilistic model for predicting crack growth behavior under random loading is pre-sented.In the model,the parameters c and m in the Paris-Erdogan Equation are taken as random variables,and their stochastic characteristic values are obtained through fatigue crack propagation tests on an offshorestructural steel under constant amplitude loading.Furthermore,by using the Monte Carlo simulation tech-nique,the fatigue crack propagation life to reach a given crack length is predicted.The tests are conducted toverify the applicability of the theoretical prediction of the fatigue crack propagation.     

Fatigue Test of Homemade Z Direction Steel Welded T Tubular Joints

This paper introduces the process and result of fatigue test of steel (Z direction steel) welded T tubular joints used in offshore engineering. Detailed measurement of stress concentration factor, stress distribution, fatigue life and crack development has been performed. Through analysis, an empirical formula of stress concentration factor for T tubular joints, fatigue S-N curve and crack propagation rule are obtained.     

管节点与船舶甲板结构中疲劳裂纹扩展方向的研究

线性断裂力学中研究裂纹的扩展通常用应力强度因子的断裂准则，但是对复合型裂纹，应力强度因子理论就发生了困难。本文用光弹性方法求得裂纹前缘的应力强度因子，然后用应变能密度因子理论研究了船舶大开口舱口角隅处疲劳裂纹和Ｔ型管节点热点处表面裂纹的扩展规律和方向，得到较好的结果