产甲壳素酶菌株的发酵条件、酶的分离纯化及酶学性质研究

利用甲壳素为唯一碳源从土壤中筛选得到1株产甲壳素酶活力较高的菌株HD002,初步鉴定其为Massilia属。确定菌株产甲壳素酶的最适培养基组成为(g/L):(NH4)2SO45,K2HPO40.7,KH2PO40.3,MgSO4.7H2O 1,胶体甲壳素10;最适产酶培养条件为:培养基起始pH值6.0,培养时间192 h,发酵液酶活力达1.314 U/mL。采用70%饱和度硫酸铵盐析、DEAE-Sepharose F.F阴离子交换层析、Sephadex G-75凝胶过滤层析对该甲壳素酶进行纯化,SDS-PAGE证明达到电泳纯。该甲壳素酶的分子量为60.2 kDa,最适反应温度为55℃,最适反应pH值为5.0,Cu2+和Fe3+对酶活力有明显的抑制作用,Ca2+和Na+对酶活力有明显的促进作用。     

混合发酵产甲壳素酶发酵条件优化及粗酶部分性质研究

利用甲壳素作为唯一碳源从土壤中筛得的真菌d,与细菌s混合发酵,对其最适产酶条件、所产甲壳素粗酶的制取以及粗酶性质进行初步研究。结果表明,混合发酵产酶的能力与单独发酵相比显著提高,混合发酵最适培养基组分为(×10~(-2) g/mL):尿素1.0,K_2HPO_4 0.07,KH_2PO_4 0.03,MgSO_4 0.05,酵母粉0.5,甲壳素1.0,pH 5.5,接种量2%(体积分数),32℃,130 r/min培养72 h,500 mL锥形瓶培养基装量为100 mL。经过优化,发酵液中甲壳素酶活力从0.73 U/mL提升到1.19 U/mL。通过对粗酶性质初步的研究,发现该酶有较好的稳定性。     

高产壳聚糖酶菌株的筛选和发酵产酶条件研究

为探讨专一性地降解甲壳质或壳聚糖的甲壳质酶或壳聚糖酶 ,从采集的土样中分离到 4株产壳聚糖酶能力较强的菌株 ,经摇瓶复筛 ,菌株YJ0 2产酶能力最强。对其发酵产酶条件的研究结果表明其产酶最适培养基组分为 (% ,w/v) :粉末壳聚糖 2 .0 ,葡萄糖 0 .1,NH4NO3 1.0 ,酵母提取物 0 .5 ,K2 HPO40 .0 7,KH2 PO40 .0 3 ,NaCl0 .5 ,MgSO4·7H2 O 0 .0 5 ,起始 pH 6.0。最适产酶培养条件是 :5 0 0mL三角烧瓶装瓶量为 15 0mL ,2 .0 % (v/v)接种量 ,3 0℃ ,15 0r/min培养 72h。在最适产酶培养条件下 ,72h时菌株YJ0 2发酵液中壳聚糖酶活力可达到 17.0 4U/mL。     

硫酸软骨素酶高产菌株的筛选、鉴定和发酵培养条件的研究

通过透明圈法从土样中初筛到2株产硫酸软骨素酶能力较高的菌株,经复筛,28号菌株产酶能力更强,对该菌株的形态特征和生理生化特性考察,初步鉴定为少动鞘氨醇单胞菌(Sphingomonas paucimobilis)。该菌株的发酵产酶条件研究表明,其产酶最适培养基组分为(%,w/v):酵母粉1.0,硫酸软骨素0.5,NaCl 0.5,KH2PO40.03,MgSO4.7H2O0.5,起始pH=8.5,其余为水。其最适产酶条件为:250mL三角瓶装液量40mL,1%(v/v)接种量,25℃,100r/min培养36h。在最适产酶培养条件下,菌株发酵液中硫酸软骨素酶的活力可达1.2U/mL。本研究筛选出产硫酸软骨素酶高的菌株,并为发酵法制备硫酸软骨素酶提供一定的实验依据。     

褐藻胶裂解酶产生菌Vibro sp.QY102的发酵条件优化

对海洋来源的Vibro sp.QY102的产褐藻胶裂解酶的发酵条件进行研究。结果表明,该菌株最适液体培养基成分为(w/v):0.5%褐藻酸钠;0.4%蛋白胨;0.3%KH2PO4;0.7%K2HPO4.3H2O;2%NaCl;0.01%MgSO4.7H2O,pH=6.0。按3%的接种量接入培养基,30℃150 r/min振荡培养120 h,产酶达到10.2 U/mL,为优化前的4.5倍。Mg2 是该菌株产酶所必需的,这在其他褐藻胶裂解酶生产菌株中未见报道。该菌株产酶发酵条件的研究,为褐藻胶裂解酶的大规模制备及应用奠定了基础。     

琼胶降解菌F-6筛选、培养条件及对条斑紫菜(Porphyra yezoensis)细胞解离作用的研究

利用琼胶作为唯一的碳源从青岛太平角海域的海水和红藻样品中筛选分离得到一株高产琼胶酶的海洋菌F-6,对其最适的产酶条件,利用琼胶酶分离条斑紫菜的原生质体和原生质体的培养进行研究。结果表明,通过单次单因子和正交实验确定琼胶降解菌株F-6最适产酶培养基配方为(W/V):琼胶0.7%;酵母粉0.3%;蛋白胨0.5%;NaCl2.0%;K2HPO40.1%;CaCl20.02%;MgSO4·7H2O0.05%;FeSO4·7H2O0.002%;起始pH=7.5,最适的发酵产酶条件为:26℃培养36h。经条件优化后,粗酶液的酶活高达631.6U/ml。发酵液经过6000g离心30min得到粗酶液,粗酶液经过8k分离膜超滤,加入1mol/L渗透剂,0.22μm滤膜过滤除菌后降解条斑紫菜组织块,成功地分离得到大量的紫菜原生质体,其产率为3×106个原生质体/g新鲜紫菜组织。原生质体经初步培养发育成愈伤组织,其成活率为60%。     

一株海洋几丁质酶产生菌的筛选及其产酶条件的初步研究

从胶州湾的海泥中分离到一株几丁质酶高产菌株。经16SrDNA序列分析,认为该菌属于假交替单胞菌(Pseudoaltermonas),并将其命名为SS01。对该菌产几丁质酶的最佳培养条件进行了研究,发现与其它几丁质酶产生菌相比,SS01菌株的最适产酶温度较低,酶活较高。在Zobell2216E培养基中,SS01菌株培养9h进入稳定期。胶体几丁质可诱导该菌几丁质酶的产生。在几丁质培养基中,SS01菌株产酶的适宜条件是:培养温度24℃,培养基起始pH7.0左右,蛋白胨为N源(5g/L),胶体几丁质为C源(5g/L),170r/min振荡培养130h,酶活可达116.2U/mL。     

烟曲霉产壳聚糖酶液体发酵条件研究

以烟曲霉(Aspergillus fumigatus)为出发菌,通过选择适合的培养条件,筛选出产壳聚糖酶的菌株。实验结果表明,烟曲霉是良好的产壳聚糖酶出发菌。烟曲霉液体发酵产壳聚糖酶最适培养基组成为:壳聚糖1%,KH2PO40.06%,尿素0.2%,(NH4)2SO40.1%,MgSO40.012%,20%土豆汁3%,NaCl 0.05%。在pH 5.0、温度28℃、摇床转速120 r/min培养条件下振荡培养3 d,烟曲霉产壳聚糖酶的能力最强,达25.1 U/mL。     

热稳定k-卡拉胶酶产生菌Bacillus sp.Car19的发酵条件优化

对一株分泌热稳定κ-卡拉胶酶印尼热泉菌进行了种属鉴定,并采用响应面法对该菌发酵产酶条件进行了优化。鉴定结果表明,该菌株属于芽孢杆菌属(Bacillus),命名为Bacillus sp.Car19(Gene Bank:KT865196)。发酵条件优化结果显示,9个环境因子影响Bacillus sp.Car19产酶量。其中影响Bacillus sp.Car19产酶量的三个主要因素分别为培养温度、培养基中Cu~(2+)浓度和培养基中Na Cl浓度。综合次要因素对Bacillus sp.Car19产酶影响,Bacillus sp.Car19最佳产酶发酵条件为:培养温度52.31℃、Cu~(2+)浓度6.93 mmol/L、Na Cl浓度37.03 g/L,培养基p H为6,接种量1%,培养时间36 h,半乳糖浓度0.3 g/L,硝酸铵浓度7 g/L,卡拉胶浓度0.5 g/L。优化后发酵上清液酶活力达到15.21 U/m L,与优化前相比提高了1.5倍。     

产壳聚糖酶菌株发酵条件优化及壳聚糖酶的分离纯化研究

从土壤中筛选得到一株产壳聚糖酶菌株P003,对其进行了发酵条件优化.结果表明其最适发酵培养条件为:(NH4)2SO42.0%,粉末壳聚糖1.0%,葡萄糖0.1%,K2HPO40.07%,KH2PO40.03%,NaCl 0.5%,MgSO4·7H2O 0.05%,酵母提取物0.3%,调pH至5.0;2.0%接种量,500 mL三角瓶装液量为150 mL,32℃下150 r/min摇床培养96 h,在此条件下菌株发酵液的壳聚糖酶活力达108 u/mL.采用硫酸铵分级盐析、离子交换层析和凝胶过滤层析等方法,从菌株的发酵液中分离出了分子质量为30.5 ku的壳聚糖酶.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,