Wind Profile Diagnosis from Surface Routine Meteorological Data Over a Coastal Area

A simple algorithm is proposed in order to transform routine surface wind speed observations near the coast to a wind at the height of the equilibrium planetary boundary layer as well as to any other height over a relatively flat coastal region. The model is based on the well known internal boundary layer (IBL) concept, Monin-Obukhov similarity theory and the resistance law, and describes the effects of the roughness transition from sea to land as well as the effect of stability on the shape of the profiles and the IBL growth. The required input weather data are no more than surface wind speed, air temperature and total cloud cover. Satisfactory agreement was found between measurements at Hellinikon airport and estimations made with the scheme. The introduction of a transition layer above the IBL did not improve the agreement to any significant extent. Mean values of the estimated wind differed by less than 1 m s ^-1 from the observed ones, a difference within the accuracy of the reported rawinsonde values. The rms error varied in the range of 17–22% of the observed average value, giving the best agreement under unstable conditions. The correlation coefficient between the observed and the estimated values of the wind, at the height of the equilibrium planetary boundary layer, ranged between 0.74 and 0.90.     

Frequency of Boundary-Layer-Top Fluctuations in Convective and Stable Conditions Using Laser Remote Sensing

The planetary boundary-layer (PBL) height is determined with high temporal and altitude resolution from lidar backscatter profiles. Then, the frequencies of daytime thermal updrafts and downdrafts and of nighttime gravity waves are obtained applying a fast Fourier transform on the temporal fluctuation of the PBL height. The principal frequency components of each spectrum are related to the dominant processes occurring at the daytime and nighttime PBL top. Two groups of cases are selected for the study: one group combines daytime cases, measured in weak horizontal wind conditions and dominated by convection. The cases show higher updraft and downdraft frequencies for the shallow, convective boundary layer and lower frequencies for a deep PBL. For cases characterized by strong horizontal winds, the frequencies directly depend on the wind speed. The temporal variation of the PBL height is determined also in the likely presence of lee waves. For nighttime cases, the main frequency components in the spectra do not show a real correlation with the nocturnal PBL height. Altitude fluctuations of the top of the nocturnal boundary layer are observed even though the boundary layer is statically stable. These oscillations are associated with the wind shear effect and with buoyancy waves at the PBL top.     

Stability Dependence of Canopy Flows over a Flat Larch Forest

The dependence on atmospheric stability of flow characteristics adjacent to a very rough surface was investigated in a larch forest in Japan. Micrometeorological measurements of three-dimensional wind velocity and air temperature were taken at two heights above the forest, namely 1.7 and 1.2 times the mean canopy height h. Under near-neutral and stable conditions, the observed turbulence statistics suggest that the flow was likely to be that of the atmospheric surface layer (ASL) at 1.7h, and of the roughness sublayer (RSL) at 1.2h. However, in turbulence spectra, canopy-induced large coherent motions appeared clearly at both heights. Even under strongly stable conditions, the large-scale motions were retained at 1.2h, whereas they were overwhelmed by small-scale motions at 1.7h. This phenomenon was probably due to the enhanced contribution of the ASL turbulence associated with nocturnal decay of the RSL depth, because the small-scale motions appeared at frequencies close to the peak frequencies of well-known ASL spectra. This result supports the relatively recent concept that canopy flow is a superimposition of coherent motions and the ASL turbulence. The large-scale motions were retained in temperature spectra over a wider region of stability compared to streamwise wind spectra, suggesting that a canopy effect extended higher up for temperature than wind. The streamwise spacing of dominant eddies according to the plane mixing-layer analogy was only valid in a narrow range at near neutral, and it was stabilised at nearly half its value under stable conditions.     

Direct Numerical Simulation of Stable Channel Flow at Large Stability

We consider a model for the stable atmospheric boundary at large stability, i.e. near the limit where turbulence is no longer able to survive. The model is a plane horizontally homogeneous channel flow, which is driven by a constant pressure gradient and which has a no-slip wall at the bottom and a free-slip wall at the top. At the lower wall a constant negative temperature flux is imposed. First, we consider a direct numerical simulation of the same channel flow. The simulation is computed with the neutral channel flow as initial condition and computed as a function of time for various values of the stability parameter h/L, where h is the channel height and L is related to the Obukhov length. We find that a turbulent solution is only possible for h/L < 1.25 and for larger values turbulence decays. Next, we consider a theoretical model for this channel flow based on a simple gradient transfer closure. The resulting equations allow an exact solution for the case of a stationary flow. The velocity profile for this solution is almost linear as a function of height in most of the channel. In the limit of infinite Reynolds number, the temperature profile has a logarithmic singularity at the upper wall of the channel. For the cases where a turbulent flow is maintained in the numerical simulation, we find that the velocity and temperature profiles are in good agreement with the results of the theoretical model when the effects of the surface layer on the exchange coefficients are taken into account. Frans Nieuwstadt, a recently retired member of the BLM Editorial Board and a well-known member of the boundary-layer/turbulence community, died unexpectedly on 18 May 2005. An obituary will appear in a later issue of BLM.     

Microstructure of Turbulence in the Stably Stratified Boundary Layer

The microstructure of a stably stratified boundary layer, with a significant low-level nocturnal jet, is investigated based on observations from the CASES-99 campaign in Kansas, U.S.A. The reported, high-resolution vertical profiles of the temperature, wind speed, wind direction, pressure, and the turbulent dissipation rate, were collected under nocturnal conditions on October 14, 1999, using the CIRES Tethered Lifting System. Two methods for evaluating instantaneous (1-sec) background profiles are applied to the raw data. The background potential temperature is calculated using the “bubble sort” algorithm to produce a monotonically increasing potential temperature with increasing height. Other scalar quantities are smoothed using a running vertical average. The behaviour of background flow, buoyant overturns, turbulent fluctuations, and their respective histograms are presented. Ratios of the considered length scales and the Ozmidov scale are nearly constant with height, a fact that can be applied in practice for estimating instantaneous profiles of the dissipation rate.     

On the Formation of an Elevated Nocturnal Inversion Layer in the Presence of a Low-Level Jet: A Case Study

We report on observed nocturnal profiles, in which an inversion layer is located at the core of a low-level jet, bounded between two well-mixed layers. High-resolution vertical profiles were collected during a field campaign in a small plain in the Israeli desert (Negev), distant 100 km from the eastern shore of the Mediterranean Sea. During the evening hours, the synoptic flow, superposed on the late sea breeze, forms a low-level jet characterized by a maximum wind speed of 12 m s ⁻¹ at an altitude of 150 m above the ground. The strong wind shear at the jet maximum generates downward heat fluxes that act against the nocturnal ground cooling. As a result, the typical ground-based nocturnal inversion is “elevated” towards the jet centre, hence a typical early morning thermal profile is observed a few hours after sunset. Since the jet is advected into the region, its formation does not depend on the presence of a surface nocturnal inversion layer to decouple the jet from surface friction. On the contrary, here the advected low-level jet acts to hinder the formation of such an inversion. These unusual temperature and wind profiles are expected to affect near-ground dispersion processes.     

大气边界层的数值模式

从大气边界层温湿特征的模拟,讨论模式的设计和处理。模式计算所得位温,混合比垂直廓线和混合层厚度等随时间变化基本反映实际大气边界层的一些特点。并从地气之间热量收支、土壤热传导方程出发计算地面温度日变化。利用Clarke的Wangara资料计算了24小时内它们的变化,并与观测值进行比较。本文还对温湿预报方程的数值解的稳定性进行了讨论。     

城乡过渡地带低空温度平流和边界层特征的观测分析

利用兰州河谷盆地城乡过渡区边界层观测资料,分析了该地区的温度平流和边界层特征。分析表明:(1)夜间热岛环流明显,白天则较弱;(2)夜间200m高度以下有较强的冷平流,在250～400m高度有较弱的暖平流,冷暖温度平流对测点上空边界层温度和层结变化有显著影响;(3)由声雷达确定的夜间边界层高度对应于Ri<1.0的高度,在这一高度范围内存在逆位温和强的风切变。本地区下垫面和复杂的地形导致夜间边界层高度随时间周期性地升高和降低,变化周期约3h。     

Long-Term Mean Wind Profiles Based on Similarity Theory

We provide general forms for long-term mean wind profiles from similarity-based wind profiles, beginning with a probabilistic adaptation of Monin–Obukhov similarity theory. We develop an analytical formulation for the stability distributions prevailing in the atmospheric surface layer, which in turn facilitates the derivation of a long-term mean wind profile based on Monin–Obukhov similarity theory. The modelled stability distributions exhibit good agreement with measurements from sites having different local conditions. The long-term wind profile formulation is further extended to include the influence of the depth of the atmospheric boundary layer (h), which becomes relevant for heights above h/3, and the resultant long-term ‘tall’ profile form also matches observations.     

Wind profiles,momentum fluxes and roughness lengths at Cabauw revisited

We describe the results of an experiment focusing on wind speed and momentum fluxes in the atmospheric boundary layer up to 200 m. The measurements were conducted in 1996 at the Cabauw site in the Netherlands. Momentum fluxes are measured using the K-Gill Propeller Vane. Estimates of the roughness length are derived using various techniques from the wind speed and flux measurements, and the observed differences are explained by considering the source area of the meteorological parameters. A clear rough-to-smooth transition is found in the wind speed profiles at Cabauw. The internal boundary layer reaches the lowest k-vane (20 m) only in the south-west direction where the obstacle-free fetch is about 2 km. The internal boundary layer is also reflected in the roughness lengths derived from the wind speed profiles. The lower part of the profile (< 40 m) is not in equilibrium and no reliable roughness analysis can be given. The upper part of the profile can be linked to a large-scale roughness length. Roughness lengths derived from the horizontal wind speed variance and gustiness have large footprints and therefore represent a large-scale average roughness. The drag coefficient is more locally determined but still represents a large-scale roughness length when it is measured above the local internal boundary layer. The roughness length at inhomogeneous sites can therefore be determined best from drag coefficient measurements just above the local internal boundary layers directly, or indirectly from horizontal wind speed variance or gustiness. In addition, the momentum and heat fluxes along the tower are analysed and these show significant variation with height related to stability and possibly surface heterogeneity. It appears that the dimensionless wind speed gradients scale well with local fluxes for the variety of conditions considered, including the unstable cases.     

étude expérimentale de la couche limite de montagne

The characteristics of the boundary layer over complex terrain (Lannemezan - lat.: 43.7° N and, long.: 0.7 ° E) are analyzed for various scales, using measurements obtained during the COCAGNE Experiment. In this first part, the dynamic characteristics of the flow are studied with respect to atmospheric stability and the relief at small (~20 km) and medium scales (~100 km). These relief scales depend on the topographical profile of the Lannemezan Plateau along the dominant axis of the wind (E-W) and the Pyrénées Mountains located at the south of the experimental site. The terrain heterogeneities have a standard deviation of ~48 m and a wavelength of ~2 km.The averaged vertical profiles of wind speed and direction over the heterogeneous terrain are analyzed. The decrease of wind speed within the boundary layer is greater than over flat terrain (WANGARA Experiment). However, a comparison between ETTEX (complex terrain) and COCAGNE vertical wind speed profiles shows good agreement during unstable conditions. In contrast, during neutral conditions a more rapid increase with normalized height is found with COCAGNE than with ETTEX and WANGARA data. The vertical profiles of wind direction reveal an influence of the Pyrénées Mountains on the wind flow. The wind rotation in the BL is determined by the geostrophic wind direction-Pyrénées axis angle (negative deviation) as the geostrophic wind is connected with the Mountain axis.When the geostrophic wind does not interact with the Pyrénées axis, the mean and turbulent wind flow characteristics (drag coefficient C _D, friction velocity u _*) depend on the topography of the plateau. When the wind speed is strong (>6 m s ^-1), an internal boundary layer is generated from the leading edge of the Plateau.     

Turbulent diffusivity and diurnal variations in the atmospheric boundary layer

Diurnal variations of the vertical profiles of wind and temperature have been surveyed, and the diffusivity and the dimensionless gradient function in the atmospheric boundary layer have been estimated. Even in the middle of the atmospheric boundary layer (e.g., below a height of 442 m), the vertical wind profile normalized by the surface friction velocity has approximately a universal profile function different from that in the surface boundary layer. Under strong stability conditions, the dimensionless gradient function has a value of about 9.     

Water vapour flux profiles in the convective boundary layer

Summary Water vapour flux profiles in the atmospheric boundary layer have been derived from measurements of water vapour density fluctuations by a ground-based Differential Absorption Lidar (DIAL) and of vertical wind fluctuations by a ground-based Doppler lidar. The data were collected during the field experiment LITFASS-2003 in May/June 2003 in the area of Lindenberg, Germany. The eddy-correlation method was applied, and error estimates of ±50 W/m² for latent heat flux were found. Since the sampling error dominates the overall measurement accuracy, time intervals between 60 and 120 min were required for a reliable flux calculation, depending on wind speed. Rather large errors may occur with low wind speed because the diurnal cycle restricts the useful interval length. In the lower height range, these measurements are compared with DIAL/radar-RASS fluxes. The agreement is good when comparing covariance and error values. The lidar flux profiles are well complemented by tower measurements at 50 and 90 m above ground and by area-averaged near surface fluxes from a network of micrometeorological stations. Water vapour flux profiles in the convective boundary layer exhibit different structures mainly depending on the magnitude of the entrainment flux. In situations with dry air above the boundary layer a positive entrainment flux is observed which can even exceed the surface flux. Flux profiles which linearly increase from the surface to the top of the boundary layer are observed as well as profiles which decrease in the lower part and increase in the upper part of the boundary layer. In situations with humid air above the boundary layer the entrainment flux is about zero in the upper part of the boundary layer and the profiles in most cases show a linear decrease.     

Study on Physical Mechanism of Influence on Atmospheric Boundary Layer Depth in the Arid Regions of Northwest China

Using the sounding data of wind, temperature, and humidity in the boundary layer and micrometeorological data on the earth's surface observed in the same period in Dunhuang arid region of Northwest China,this paper researches characteristics of potential temperature, wind, and humidity profiles, confirms the structure and depth of thermodynamic boundary layer in Dunhuang region, and analyzses the relationship of depth of thermodynamic boundary layer with surface radiation, buoyancy flux as well as wind speed and wind direction shear in the boundary layer. The results show that the maximum depth of diurnal convective boundary layer is basically above 2000 m during the observational period, many times even in excess of 3000 m and sometimes up to 4000 m; the depth of nocturnal stable boundary layer basically maintains within a range of 1000-1500 m. As a whole, the depth of atmospheric boundary layer is obviously bigger than those results observed in other regions before. By analyzing, a preliminary judgement is that the depth of atmospheric thermodynamic boundary layer in Dunhuang region may relate to local especial radiation characteristics, surface properties (soil moisture content and heat capacity) as well as wind velocity shear of boundary layer, and these properties have formed strong buoyancy flux and dynamic forcing in a local region which are fundamental causes for producing a super deep atmospheric boundary layer.     

A bulk similarity approach in the atmospheric boundary layer using radiometric skin temperature to determine regional surface fluxes

Profiles of wind velocity and temperature in the outer region of the atmospheric boundary layer (ABL) were used together with surface temperature measurements, to determine regional shear stress and sensible heat flux by means of transfer parameterizations on the basis of bulk similarity. The profiles were measured by means of radiosondes and the surface temperatures by infrared radiation thermometry over hilly prairie terrain in northeastern Kansas during the First ISLSCP Field Experiment (FIFE). In the analysis, the needed similarity functions were determined and tested; the main scaling variables used for the ABL were h _i , the height of the convectively mixed layer, and V _a and _a, the wind speed and potential temperature averaged over the mixed layer. Good agreement (r = 0.80) was obtained between values of friction velocity u _* determined by this ABL bulk similarity approach and those obtained by Monin-Obukhov similarity in the surface sublayer. Similarly, values of surface flux of sensible heat H determined by this method compared well (r = 0.90) with the regional means measured at six ground stations. The corresponding regional evaporation values, determined with the energy budget equation, also compared favorably (r = 0.94).     

Kinematic models of a dry convective boundary layer compared with dual-Doppler radar observations of wind fields

The kinematic structure of the convective boundary layer, observed by a dual-Doppler radar system, is compared with the structure predicted by simple shear models. We first consider the models to be inviscid, then add viscous effects. Model 1 assumes a linear ambient wind profile from the surface through the boundary layer, and a constant wind above. The shear layer is assumed to be statically neutral, but static stability is permitted in the region above the shear. Model 2 has a hyperbolic tangent ambient wind profile.After considering the inviscid models, some of the effects of viscosity are incorporated into the models in a crude way, and the results are compared.We conclude that although the presence of shear is important, the kinematic structure is relatively independent of the details of the wind and temperature profiles. Viscosity has important effects, especially near the critical level where the disturbance velocity is equal to the wind speed. The patterns predicted by both models agree very well with the dual-Doppler radar observations when viscosity is included.     

Comparing mixing-length models of the diabatic wind profile over homogeneous terrain

Models of the diabatic wind profile over homogeneous terrain for the entire atmospheric boundary layer are developed using mixing-length theory and are compared to wind speed observations up to 300 m at the National Test Station for Wind Turbines at Høvsøre, Denmark. The measurements are performed within a wide range of atmospheric stability conditions, which allows a comparison of the models with the average wind profile computed in seven stability classes, showing a better agreement than compared to the traditional surface-layer wind profile. The wind profile is measured by combining cup anemometer and lidar observations, showing good agreement at the overlapping heights. The height of the boundary layer, a parameter required for the wind profile models, is estimated under neutral and stable conditions using surface-layer turbulence measurements, and under unstable conditions based on the aerosol backscatter profile from ceilometer observations.     

Use of a High-Resolution Sodar to Study Surface-layer Turbulence at Night

Measurements in the atmospheric surface layer are generally made with point sensors located in the first few tens of metres. In most cases, however, these measurements are not representative of the whole surface layer. Standard Doppler sodars allow a continuous display of the turbulent thermal structure and wind profiles in the boundary layer up to 1000 m, with a few points, if any, in the surface layer. To overcome these limitations a new sodar configuration is proposed that allows for a higher resolution in the surface layer. Because of its capabilities (echo recording starting at 2 m, echo intensity vertical resolution of approximately 2 m, temporal resolution of 1 s) this sodar is called the surface-layer mini-sodar (SLM-sodar). Features and capabilities of the SLM-sodar are described and compared with the sodar. The comparison of the thermal vertical structure given by the SLM-sodar and the sodar provides evidence that, in most cases, the surface layer presents a level of complexity comparable to that of the entire boundary layer. Considering its high vertical resolution, the SLM-sodar is a promising system for the study of the nocturnal surface layer. The nocturnal SLM-sodar measurements have shown that, depending on wind speed, the structure of the surface layer may change substantially within a short time period. At night, when the wind speed is greater than 3 m s⁻¹, mechanical mixing destroys the wavy structure present in the nocturnal layer. Sonic anemometer measurements have shown that, in such cases, also the sensible heat flux varies with height, reaching a peak in correspondence with the wind speed peak. Under these conditions the assumption of horizontal homogeneity of the surface layer and the choice of the averaging time need to be carefully treated.     

登陆台风边界层风廓线特征的地基雷达观测

为了分析登陆台风边界层风廓线特征,利用2004—2013年中国东南沿海新一代多普勒天气雷达收集的17个登陆台风资料,采用飓风速度体积分析方法,反演登陆台风的边界层风场结构特征。与探空观测对比表明,利用雷达径向风场可以准确地反演登陆台风的边界层风场结构,其风速误差小于2 m/s,风向误差小于5°。所有登陆台风合成的边界层风廓线显示,在近地层(100 m)以上,边界层风廓线存在类似急流的最大切向风,其高度均在1 km以上,显著高于大西洋观测到的飓风边界层急流高度(低于1 km)。陆地边界层内低层入流强度也明显大于过去海上观测,这主要是由陆地上摩擦增大引起。越靠近台风中心,边界层风廓线离散度越大,其中,径向风廓线比全风速以及切向风廓线离散度更大。将风廓线相对台风移动方向分为4个象限,分析边界层风廓线非对称特征显示,台风移动前侧入流层明显高于移动后侧。最大切向风位于台风移动左后侧,而台风右后侧没有显著的急流特征,与过去理想模拟的海陆差异导致的台风非对称分布特征一致。     

Diabatic wind speed profiles in coastal regions: Comparison of an internal boundary layer (IBL) model with observations

A model is presented to transform wind speed observations at a single height over sea or near the coast to any possible location and height in a topographic flat coastal region (up to distances of about 5 km from the coast and up to heights of 100 m). Only moderate and strong winds from the sea are considered, which are particularly important for wind energy applications. The model, called diabatic coast model, which is based on the well known internal boundary layer (IBL) concept and Monin-Obukhov similarity theory, describes the effects of the roughness transition from sea to land as well as the effect of stability on the shape of the profiles and the IBL growth. The predicted IBL heights are compared with published data.In the second part of this paper, the model is compared with measurements taken at the Maasvlakte location near the Dutch coast. It is shown that a neutral formulation of the IBL height is sufficient to model the overall mean wind speed with height, but that stability corrections are needed to describe the diurnal variations in wind speed properly. Finally, an application is given, where a single routine wind speed observation at the coast, combined with air-water temperature differences is used to predict the wind speed at 500m from the coast at heights of 10 and 53 m. The results are in good agreement with the measurements.