饱和黏土中固定锚腚拖曳锚嵌入轨迹预测模型

饱和黏土中固定锚腚拖曳锚的嵌入轨迹和承载力预测是深水系泊系统设计的关键。从固定锚腚拖曳锚在饱和黏土海床嵌土的初始状态出发,将固定锚腚拖曳锚和周围土体视作宏单元,假设在锚链拉力作用下宏单元沿土体屈服面法向运动,利用锚链方程计算锚眼拉力,基于增量迭代法建立了预测固定锚腚拖曳锚嵌入运动轨迹和锚眼拉力的模型,编制了相应的计算程序。利用程序预测了Bruce Dennla MK4固定锚腚拖曳锚、Murff算例拖曳锚在饱和黏土中的运动轨迹和承载力,结果表明：本文所建立的模型预测结果正确,可以用于预测固定锚腚拖曳锚嵌入饱和黏土全过程中板锚的运动轨迹、运动形态和锚眼拉力;固定锚腚拖曳锚嵌入过程中,锚运动形态有一个调整过程,因此,旋转角先减小,而后增加,并逐渐趋于稳定值。     

拖曳锚与安装缆绳相互作用力计算方法研究

深水系泊系统及其系泊基础的研发已成为国际海洋工程领域的前沿和关键课题,拖曳锚因其在承载力和深水安装中的诸多优势而具有良好的发展前景。在拖曳锚安装过程中,锚板与安装缆绳在系缆点处发生复杂的相互作用,分析二者之间的相互作用可等价为分析系缆点拖曳力的大小,研究拖曳锚与安装缆绳相互作用力的计算方法对认识锚板在海床土中的受力以及确定拖曳锚安装船的吨位具有重要指导意义。分别基于嵌入缆绳和拖曳锚在海床土中的力学模型,首次推导出适用于黏性土和无黏性土的系缆点拖曳力表达式,并开展模型试验验证,对比两类拖曳力计算方法的精度和稳定性,结果表明,两类计算方法均能合理预测系缆点拖曳力,但基于拖曳锚受力模型获得的表达式更为精确和稳定;通过参数考察,探究系缆点拖曳力预测模型中各参数的影响效应;经过与试验对比,给出关键参数的建议取值,该取值对研究结构与土体的相互作用问题具有重要参考价值。     

考虑锚胫作用下拖曳锚在成层土中的嵌入机制

深水系泊系统及其系泊基础的开发已成为发展清洁能源“海上风电”项目的关键课题。拖曳锚由于其较大的承载力和易安装等诸多优势而具有较好的发展前景。基于极限塑性上限分析法,建立了考虑锚胫作用的拖曳锚在成层土中的嵌入轨迹、姿态以及承载力预测模型。利用已有模型试验对本模型进行验证,结果表明：考虑锚胫作用模型轨迹预测误差控制在13.5%,轨迹和角度预测误差相比于未考虑锚胫作用的模型分别降低了78.32%和36.9%。硬土层的强度、厚度和深度共同制约着拖曳锚的嵌入能力。首先,强度比影响最明显,强度比越大,嵌入深度越小,直至无法穿透硬土层;其次,是深度影响,深度越大,承载力越大。能够穿透硬土层的条件下深度对轨迹和角度影响不明显,不能够穿透硬土层条件下深度越大,嵌入深度越大,最终角度越小;最后,是厚度影响,硬土层厚度越大,嵌入过程中承载力越大。     

基于上限法的条形锚板抗拔承载力分析

以极限分析上限理论为基础,利用旋转块体集的组合来构造条形锚板的运动许可速度场。分析了不排水黏土中深埋和浅埋条形锚板的抗拔承载力上限解,研究了锚板在不同埋置倾角和深度条件下的抗拔承载力和破坏面的特性,并将计算结果与已有计算方法进行了对比。分析结果表明：在不排水黏土中深埋条形锚板抗拔承载力与锚板的埋置方位和锚板的粗糙度无关,但完全光滑条件下破坏面扇圆部分的半径只有完全粗糙条件下的一半;在考虑无重土情况下浅埋条形锚板的抗拔承载力系数随锚板埋深比的增大而增大,破坏面也随埋深比的增加而逐渐扩大。所得上限解与已有文献解答较为吻合,而且求解所得破坏面更为直观,能为工程设计提供参考依据。     

塑性极限分析鱼雷锚锚尖贯入阻力

鱼雷锚安装过程中,锚尖形状影响尖部贯入阻力进而影响贯入深度。基于塑性极限分析理论下限法分析不同锚尖长径比x的椭圆形锚尖的贯入阻力和贯入阻力系数,并考虑了贯入深度、锚-土界面摩擦对贯入阻力以及贯入阻力系数的影响。结果表明:(1)锚-土界面光滑时,锚尖贯入阻力系数随着锚尖长径比的增大而减小;锚-土界面粗糙时,锚尖贯入阻力系数随着锚尖长径比的增大而增大。(2)摩擦力对贯入阻力系数的影响随着ξ增大而增大。(3)随着埋置深度增加,贯入阻力系数受x影响最小时所对应的摩擦系数逐渐减小。(4)当锚-土界面摩擦系数ω 0.75时,工程中可选用ξ1的锚尖用以减小端部贯入阻力;当ω0.26时,ξ1的锚尖提供更小的端部贯入阻力。锚尖长径比ξ=0和ξ=1的下限解与前人研究的桩基和圆形结构的理论解较为一致,进一步验证了所提出的椭圆形锚尖下限法模型的可行性。     

锚板在正常固结黏土中的承载力

在岩土工程中,锚板通常被用来提供竖直或水平抗拔力,比如发射塔的基础、板桩墙结构和悬浮式海洋平台的基础。采用弹-塑性有限元方法对正常固结不排水黏土中的条形锚板进行数值分析,以图表形式给出了不同埋深率、不同上拔倾角、不同锚-土黏结形式下条形锚板的承载力系数和周围土体的流动机构,分析了土体自重对锚板承载力的影响,并给出了不同情况下锚板的极限承载力系数。采用基于重新划分网格并插值状态变量的大变形分析方法（RITSS）,分析了正常固结黏土中锚板在连续拔出过程中的承载力变化以及土重对锚-土分离模式的影响。     

非完全粗糙平板锚旋转安装过程中的丢失埋深研究

吸力贯入平板锚被用于系泊深海浮式结构,实际应用中必须预估平板锚旋转安装过程中的丢失埋深。采用大变形有限元方法探索非完全粗糙平板锚在正常固结黏土中的旋转过程。大变形有限元法通过网格重剖避免平板锚大幅值平动和转动引起的土体单元扭曲。根据平板锚旋转到达的埋深,实时更新“锚-土”界面上的摩擦剪切强度。将数值模拟结果与离心机模型试验进行对比验证,表明高岭土中平板锚表面的粗糙系数约为0.3。平板锚丢失埋深随粗糙系数的减小而增大,但粗糙系数对丢失埋深的影响受平板锚厚度比和拉力偏心比的耦合作用。厚度比和偏心比越小,粗糙系数对丢失埋深的影响越显著。     

考虑土拱效应预应力锚拉桩土压力研究

针对预应力锚拉桩设计中土压力计算模式存在的问题,借鉴工程设计中的点锚和格构锚原理,提出了一种新的计算方法--基于三维土拱效应的土压力计算模式。利用土条极限平衡原理,推导了作用在桩及挡板上的土压力,建立了表征土压力强度的1阶线性微分方程,得到了沿桩身轴线的土压力分布曲线,并从参数 和 的变化对土压力的影响方面,与《重庆市地质灾害防治工程设计规范》[1]和《建筑边坡工程技术规范》[3]的计算结果进行了对比分析,结果表明桩板上所受土压力沿桩板竖向呈锯齿状分布,土压力强度计算值远小于规范计算值; 的变化对土压力有明显影响,工程设计中不应忽略 对减小土压力的贡献;考虑土拱效应更符合工程实际受力特性     

拖曳锚安装缆绳在海床土中的反悬链形态研究

由于在抗拔承载力和深水安装中的优势,拖曳锚在深水系泊系统中具有良好的发展前景。在拖曳锚安装过程中,安装缆绳和锚之间存在复杂的相互作用,安装缆绳在海床土中的反悬链形态将直接影响锚的嵌入和运动,对反悬链形态的研究有助于提高锚的嵌入性能、准确预测锚的运动轨迹以及解决锚在安装中的精确定位问题。基于嵌入缆单元在海床土中的力学模型,推导出适用于黏性土和无黏性土的反悬链方程,利用该方程可求出安装缆绳在海床土中的反悬链形态;通过在缆绳上布置倾角传感器并运用圆弧递推方法,设计出可实时测量嵌入缆形态的试验技术,为验证试验技术的合理性,在空气中分别选取3种典型缆绳形态进行模拟,结果表明：模拟形态与真实形态吻合良好,并具有较高精度;利用实时测量技术开展模型试验,对反悬链方程进行了考察,验证了其模拟嵌入缆反悬链形态的精度,并获取了对拖曳锚安装过程中反悬链形态变化规律的直观认识。     

新型深水系泊基础研究进展

介绍了几种国际上广泛应用于深水锚泊的新型系泊基础（吸力锚、法向承力锚、吸力式贯入锚和动力贯入锚）,并结合国内外的最新研究进展,分别针对吸力锚安装过程中的海床阻力和内部土塞发展、服役阶段的承载力特性,法向承力锚安装时的拖曳轨迹和三维受力状态下的承载力,吸力式贯入锚的“keying”过程,动力贯入锚的最终安装深度和承载力,以及锚泊线与海床的接触问题等当前国际上研究的重点和热点内容进行了简要地评述,旨在通过分析当前新型深水锚在设计、施工以及承载机制等方面的不足,以探索深水系泊基础发展的新趋势     

斜坡浅埋水平条形锚板抗拔承载力的极限分析

针对山区和丘陵等复杂地形下浅埋锚板抗拔承载力计算问题,基于极限分析上限定理、非线性Mohr-Coulomb强度准则及其关联流动法则,构造了斜坡浅埋水平条形锚板的曲线型破裂机制和机动许可速度场,采用变分极值原理获得了其上方土体破裂面方程和抗拔承载力的上限解,分析了斜坡倾角和锚板埋深对锚板抗拔承载力的影响。结果表明:随着斜坡倾角的增大,锚板抗拔承载力逐渐减小,此时其上方两侧土体破裂面不再对称且整体向下坡侧偏移;锚板抗拔承载力及其上方两侧土体破裂面宽度均随着埋深增大而增加;锚板埋深越小,斜坡倾角对其抗拔承载力的影响越大,应在计算中予以考虑,以更合理地反映斜坡浅埋水平条形锚板的抗拔承载特性。     

Three-dimensional numerical analysis of the keying of vertically installed plate anchors in clay

Plate anchors, such as suction embedded plate anchors and vertically driven plate anchors, offer economically attractive anchoring solutions for deep/ultra-deep water offshore developments. The rotation/keying processes of plate anchors will cause embedment losses, which lead to decreases of the uplift resistances of the anchors in normally consolidated soil. In the present paper, the keying processes of vertically installed strip and square plate anchors are simulated using the 3-D large deformation finite element method. The effects of loading eccentricity and pullout angle on the embedment loss during keying are investigated. Both the development of the uplift resistance and the soil flow mechanisms are presented. The numerical results show that the loading eccentricity e/B has a much larger effect on the embedment loss than the pullout angle does. The anchor shape has a minimal effect on the loss in anchor embedment. The shape factors (square/strip) are 1.05–1.09 for loss of embedment and 1.10–1.19 for capacity.     

软土中浅埋法向承力锚位移破坏标准模型试验

为确定浅埋软黏土中法向承力锚的位移破坏标准,利用实验室自行开发的电动伺服加载控制装置,对埋置在饱和软黏土中深度为3倍锚板宽度、系缆力角度为30°的法向承力锚模型进行了荷载和位移控制的静力加载试验。依据试验结果,以极限承载力与锚板宽度为参考,对锚板法向荷载与位移进行归一化处理,通过归一化曲线确定了法向承力锚的位移破坏标准,即破坏位移约为0.38倍锚板宽度。另外,依据锚板的尺寸、埋深及试验土体的强度条件,利用经验公式对锚的极限承载力进行了计算。结果表明,以该位移破坏标准确定的极限承载力与经验公式计算结果基本一致,两者相差均不超过10%,初步验证了该位移破坏标准的合理性。     

Passive earth pressure on embedded vertical plate anchors in sand

Passive earth pressure on embedded anchor plates constitutes a viable resisting force for the design of underground structures. In the current practice, these forces are empirically calculated, ignoring the effects of the depth of embedment and the level of consolidation of the surrounding soil, which takes place during plate installation on the in situ stress levels. Accordingly, wide discrepancies between predicted and measured pullout capacities of these plates were reported in the literature. Numerical model was developed using finite-element technique and the constitutive law of Mohr?CCoulomb to simulate the case of a retaining wall partially supported by an embedded anchor plate in sand. The results produced in this investigation showed that the passive earth pressure acting on anchor plates increases due to the increase of angle of shearing resistance and the overconsolidation ratio of sand, and it decreases due to an increase of the embedment depth of anchor. Design theories were developed for the case of embedded anchor plate in overconsolidated sand. The theories developed will satisfy the design needed in terms of allowable pullout load and/or displacement.     

浅埋平板圆锚竖向拉拔极限承载力计算方法

采用自制可视化试验装置开展了平板圆锚的拉拔模型试验,基于数字照相测量技术对极限拉拔下锚周土体的位移变形场进行了量化分析。在本次试验的埋深比范围内,极限承载力随埋深比增加而非线性增大,但增长速率逐渐减缓;观测到的锚周土体滑动面与地面、锚板所围区域整体呈现出“底大、顶小、径长”的倒喇叭形状;滑动面可用两条直线段来近似描述;极限拉拔力学模型由一个截面直径上小下大的倒圆台和一个等截面圆柱体组成。根据极限平衡条件推导建立了砂土中浅埋平板圆锚竖向拉拔极限承载力的计算方法,该方法对4组试验数据的计算较其他4种方法与试验实测值更为接近,且离散性更小,效果较好。     

Three-dimensional analysis of vertical square anchor plate in cohesionless soil

ABSTRACT

Vertical anchor plates are often provided to increase the performance of various geotechnical engineering structures such as sheet pile walls, bulkheads, bridge abutments and offshore structures. Hence, the safe design of such structures needs a better understanding of the 3D behaviour of the anchor plate. This paper presents and discusses the results obtained from a series of 3D finite-difference analyses of vertical square anchor plate embedded in cohesionless soil. The 3D model is found to closely predict experimental pullout load–displacement relationship. The failure mechanism observed in the numerical model is found to be very similar to the failure reported in experimental studies. For a given embedment depth, the stiffness of the breakout factor–displacement response substantially reduces with increase in anchor plate size. However, the ultimate reduction in anchor capacity is found to approximately 8% with an increase in anchor size from 0.1 to 1 m. Numerical analysis reveals that at deeper embedment depth, the friction angle of sand is the critical parameter in enhancing the performance of anchor plate. The obtained 3D model results are then compared with the published results and are found to be reasonably in good agreement with each other.     

Interaction Effect of Group of Helical Anchors in Cohesive Soil Using Finite Element Analysis

In this paper, the interaction effect of a group of two and four symmetrical as well as asymmetrical helical anchors resting in homogeneous cohesive soil deposit with different helix configurations is determined using finite element analysis. The anchors were pulled to its ultimate failure controlling the displacement. Eight different types of anchor configuration were considered in the analysis, where mainly the number of helical plates, the depth of upper- and lower-most helical plates and the ratio of spacing between the helical plates to the diameter of the plate were varied. The variation of load–displacement curve for each anchor in the group was obtained and subsequently, the ultimate uplift capacity of each anchor was determined. The soil was assumed to follow Mohr–Coulomb failure criteria. The present theoretical observations are generally found in good agreement with those theoretical and experimental results available in the literature for single isolated helical anchor.