Influences of coupled wind–water processes on suspended sediment grain size: an example from tributaries of the Yellow River / Influences de processus couplés éoliens-hydriques sur la granulométrie des matières en suspension: exemple d'affluents du Fleuve Jaune

Abstract

Some unique coupled wind–water erosion processes exist in the desert-loess transitional zone in the middle Yellow River basin. Based on data from 40 stations on 29 rivers, a study was made on the influence of such processes on suspended sediment grain-size characteristics of the tributaries of the Yellow River. Results show that the percentage of >0.05-mm grain size decreases with the increased annual mean precipitation, but increases with the increase in the annual mean number of sand-dust storm days. The percentage of <0.01-mm grain size increases with the increase in the annual mean precipitation, but decreases with the increase in the annual number of sand-dust storm days. Based on annual mean data from 40 stations, multiple regression equations were established between the percentages of >0.05-mm grain size (r _>0.05) and <0.01-mm grain size (r _<0.01), annual mean precipitation (P _m) and annual mean number of sand-dust storm days (D _ss). On this basis, the relative contributions of the variations in D _ss and P _m to the variation in r _>0.05 and r _<0.01 were estimated. The results indicate that the variation in sand-dust storm frequency exerts greater influences on the variation in grain-size characteristics of suspended load than does the variation in annual mean precipitation. With the increase in the coupled wind–water processes index, expressed by P _m/D _ss, the percentage of >0.05-mm grain size in suspended sediment decreases and the percentage of <0.01-mm grain size increases. With the variation in P _m/D _ss, different combinations of r _>0.05 with r _<0.01 appear, which have some influence on the formation of hyperconcentrated flows. There exist some optimal ratios of coarse to fine fractions in suspended sediment that make sediment concentrations of hyperconcentrated flows the highest. The optimal r _>0.05/r _<0.01 value is related to some range of the index P _m/D _ss. When the P _m/D _ss index falls in this range, the optimum combination of relative coarse with fine sediments in the suspended load appears, and thus results in the peak values of sediment concentration.     

Downstream variation in bed sediment size along the East Carpathian rivers: evidence of the role of sediment sources

Taking as an example six main rivers that drain the western flank of the Eastern Carpathians, a conceptual model has been developed, according to which fluvial bed sediment bimodality can be explained by the overlapping of two grain size distribution curves of different origins. Thus, for Carpathian tributaries of the Siret, coarse gravel joins an unimodal distribution presenting a right skewness with enhanced downstream fining. The source of the coarse material distributions is autohtonous (by abrasion and hydraulic sorting mechanisms). A second distribution with a sandy mode is, in general, skewed to the left. The source of the second distribution is allohtonous (the quantity of sand that reaches the river‐bed through the erosion of the hillslope basin terrains). The intersection of the two distributions occurs in the area of the 0·5–8 mm fractions, where, in fact, the right skewness (for gravel) and left skewness (for sand) histogram tails meet. This also explains the lack of particles in the 0·5–8 mm interval. For rivers where fine sediment sources are low, the 0·5–8 mm fractions have a higher proportion than the fractions under 1 mm. For the Siret River itself, bed sediment bimodality is greatly enhanced due to the fact that the second mode is more than 25% of the full sample. As opposed to its tributaries, the source of the first mode, of gravel, is allohtonous to the Siret river, generated by the massive input of coarse sediment through the Carpathian tributaries, while the second mode, of the sands, is local. In this case we can also observe that the two distributions of particles of different origins overlap in the 0·5–8 mm fraction domain, creating the illusion of ‘particle lack’ in the fluvial bed sediments. Copyright © 2007 John Wiley & Sons, Ltd.     

Real-time prediction of the peak suspended sediment concentration and sediment yield of the Lao-Nung River during storms

Based on rainfall erosion of soil and suspended sediment transport in storm events, a method is proposed to predict peak suspended sediment concentration and suspended sediment yield in watersheds based on rainfall characteristics prior to peak rainfall intensity. The rainfall characteristics factors that dominate peak suspended sediment concentration C_p are rainfall erosion factor R_ef, first peak rainfall intensity of area-average rainfall i_p1 and antecedent precipitation index I_ap; the rainfall characteristics factors that dominate suspended sediment yield Y_ss in storm events are total rainfall P, suspended sediment yield factor R_sf and antecedent precipitation index I_ap. This research focuses on watersheds in Liau-Kwei observation station along Lao-Nung River in southern Taiwan as the research object, and adopts the PSED-model to simulate the discharge hydrograph, suspended sediment concentration hydrograph and suspended sediment yield in 11 storm events for analysis. The analytical results show that there is a good correlation between the above-mentioned rainfall characteristics factors and C_p as well as Y_ss, thus enabling C_p and Y_ss to be predicted by using Expressions (13) and (14). These two expressions are utilized to predict C_p and Y_ss of Typhoon Morakot in 2009, and the results are compared with those from simulation by using the PSED-model. The result of comparison shows there is a good capability in predicting. For the watersheds where it is necessary to predict C_p and Y_ss of a storm event for the benefit of effective operation of water resource facilities, the aforesaid rainfall characteristics factors can be utilized to establish applicable models for prediction.     

Coarse bed load transport in an alluvial gravel bed stream,Dupuyer Creek,Montana

Coarse bed load was sampled in a gravel/cobble bed stream during two major floods in the snowmelt runoff season. The channel is characterized by high rates of bank erosion and, therefore, high rates of sediment supply and bed load flux. Peak discharge reached four times bank‐full, and bed load was sampled at flows 0·7–1·7 times bank‐full. A large aperture bed load sampler (1 m by 0·45 m) captured the largest particles in motion, and specifically targeted the coarse bed load size distribution by using a relatively large mesh (32 mm or D₂₅ of streambed surface size distribution). Bed load flux was highly variable, with a peak value of 0·85 kg/s/m for the coarse fraction above 38 mm. Bed load size distribution and maximum particle size was related to flow strength. Entrainment was size selective for particles D₇₀ and larger (88–155 mm), while particles in the range D₃₀–D₇₀ (35–88 mm) ceased to move at essentially the same flow. Bed load flux was size selective in that coarse fractions of the streambed surface were under‐represented in or absent from the bed load. Painted tracer particles revealed that the streambed surface in the riffles could remain stable even during high rates of bed load transport. These observations suggest that a large proportion of bed load sediments was sourced from outside the riffles. Repeat surveys confirmed major scour and fill in pools (up to 0·75 m), and bank erosion (>2 m), which together contributed large volumes of sediment to the bed load. Copyright © 2007 John Wiley & Sons, Ltd.     

Displacement and transport of marked pebbles,cobbles and boulders during floods in a steep mountain stream

In a small experimental catchment of the Dolomites (Rio Cordon, 5 km²) field observations have been carried out on the movement of various sized bed material particles. Displacement length of 860 marked pebbles, cobbles and boulders (0·032 < D < 0·512 m) has been measured along the river bed during individual snowmelt and flood events in the periods 1993–1994 and 1996–1998. Floods were grouped into two categories. The first includes ‘ordinary’ events, which are characterized by peak discharges with a return period of 1–5 years and by an hourly bedload rate not exceeding 20 m³ h^?1. The second refers to ‘exceptional’ events with a return period of 50–60 years. A flood of this latter type occurred on 14 September 1994, with a peak discharge of 10·4 m³ s^?1 and average hourly bedload rate of 324 m³ h^?1. The variation according to grain size of total displacement length L_i depends on the degree of mobilization of the individual fractions of the bed surface: L_i is independent of D_i for smaller, fully mobile grain sizes and decreases rapidly with D_i for larger fractions in a state of partial transport. Sustained selective transport without a supply of sediment from upstream leads to the development of a stable coarse armoured surface through progressive winnowing of finer material from the bed surface. With supply unlimited conditions for transport, both the occurrence of extreme events and the duration of a sequences of ‘ordinary’ floods play an important role in the degree of mobilization of the individual fractions of the bed. Copyright © 2004 John Wiley & Sons, Ltd.     

The performance of grass filter strips in controlling high‐concentration suspended sediment from overland flow under rainfall/non‐rainfall conditions

There is little information on the performance of vegetative filter strips (VFS) in filtering high‐concentration sediment from subcritical overland flow. Flume experiments on simulated grass strips were conducted using combinations of three slope gradients (3°, 9° and 15°), five 1‐m‐wide slope positions (from upslope to downslope), two flow rates (60 and 20 L min^‐1 m^‐1) and sediment concentrations of 100–300 kg m^‐3 under simulated rainfall and non‐rainfall conditions. The results showed that sediment deposition efficiency increased with VFS width as a power function. Rainfall significantly reduced sediment deposited within VFS. Higher sediment concentration corresponded to a larger sediment deposition load but reduced deposition efficiency. Flow rate had a negative effect on deposition efficiency but no effect on deposition load. Sediments were more easily deposited at the upper slope position than downslope, and the upper slope position had a higher percentage of coarse sediments. The deposited sediment had significantly greater median diameters (D₅₀) than the inflow sediment. A greater proportion of coarse sediments larger than 25 µm in diameter were deposited, and particles smaller than 1 µm and of 10–25 µm had a better deposition performance than particles of 1–10 µm. Rainfall reduced the deposited sediment D₅₀ at a slope gradient of 3° and had no significant influence on it at 9° or 15°. A higher sediment concentration led to a smaller D₅₀ of the deposited sediment. Rainfall had no significant effect on overland flow velocity. Both the deposited sediment load and D₅₀ decreased with increasing flow velocity, and flow velocity was the most sensitive factor impacting sediment deposition. The results from this study should be useful to control sediment flowing into rivers in areas with serious soil erosion. Copyright © 2013 John Wiley & Sons, Ltd.     

Effects of grain-size distribution and shape on sediment bed stability,near-bed flow and bed microstructure

Different studies investigating the stability of mixed sediment have found that the fine fraction can either stabilize or mobilize the bed. This study aims to find where the transition between these two modes occurs for sandy sediment and to identify the underlying (grain-scale) processes. Flume experiments with bimodal sediment were used to investigate near-bed processes of a non-cohesive sediment bed, and in particular how the grain shape and the ratio of different grain sizes influence bed mobility. Medium sand (D_50,c ≈ 400 μm) was mixed with 40 % fine material of different diameters (D_50,f = 53; 111; 193 μm) and subjected to increasing flow velocities (U = 1.3–22.2 cm s^-1). The bed mobility (i.e. the change of the bed level over time), turbidity and near-bed hydrodynamics were analysed. Selected results were compared with similar previous experiments with spherical glass beads. The findings indicate that, due to the complex grain shapes of natural sediment, a sand bed is more stable than a bed composed of glass beads. The grain-size ratio RD = D_c /D_f between the coarse and fine grain diameters controls whether the mixed bed is stabilized or mobilized by the presence of fines, with the transition between the modes occurring at RD = 4–5.5. Mixed beds with a very low RD < 2 behave like a unimodal bed. The results suggest that RD and grain shape influence bed roughness, near-bed flow, bed microstructure and the flow into and through the upper bed layers, which subsequently governs bed mobility. The interplay between all these processes can explain the transition between the stabilizing effect (high RD, small pore space) and the mobilizing effect (low RD, large pore space) of a fine fraction in a grain-size mixture. © 2018 John Wiley & Sons, Ltd.     

Residual OSL signals in modern fluvial sediments from the Yellow River (HuangHe) and the implications for dating young sediments

The Yellow River is characterized by its tremendous sediment load. In this study we investigated the residual OSL signals in modern fluvial sand and suspended-sediment samples from the middle reach of the river. The residual equivalent dose (D_e) is found to vary with grain size, mineralogy and the techniques used for the D_e determination. The results indicate that the OSL signals in some grains from these samples were not completely bleached prior to burial, the maximum individual D_e value obtained is up to 56 Gy. The results also show that coarse grains are generally better bleached at deposition than fine grains; the fine-grained quartz from suspended sediments are better bleached than the fine-grained quartz from the fluvial sand deposits. The D_es obtained using quartz TT-OSL signals are up to ～380 Gy for these modern samples.     

In situ characterization of grain‐scale fluvial morphology using Terrestrial Laser Scanning

The grain‐scale morphology of fluvial sediments is an important control on the character and dynamics of river systems; however current understanding of its role is limited by the difficulties of robustly quantifying field surface morphology. Terrestrial Laser Scanning (TLS) offers a new methodology for the rapid acquisition of high‐resolution and high‐precision surface elevation data from in situ sediments. To date, most environmental and fluvial applications of TLS have focused on large‐scale systems, capturing macroscale morphologies. Application of this new technology at scales necessary to characterize the complexity of grain‐scale fluvial sediments therefore requires a robust assessment of the quality and sources of errors in close‐range TLS data. This paper describes both laboratory and field experiments designed to evaluate close‐range TLS for sedimentological applications and to develop protocols for data acquisition. In the former, controlled experiments comprising high‐resolution scans of white, grey and black planes and a sphere were used to quantify the magnitude and source of three‐dimensional (3D) point errors resulting from a combination of surface geometry, reflectivity effects and inherent instrument precision. Subsequently, a methodology for the collection and processing of grain‐scale TLS data is described through an application to a coarse grained gravel system, the River Feshie (D₅₀ 32 to 63 mm). This stepwise strategy incorporates averaging repeat scans and filtering scan artefact and non‐surface points using local 3D search algorithms. The sensitivity of the results to the filter parameter values are assessed by careful internal validation of Digital Terrain Models (DTMs) created from the resulting point cloud data. The transferability of this methodology is assessed through application to a second river, Bury Green Brook, dominated by finer gravel (D₅₀ 18 to 33 mm). The factor limiting the resolution of DTMs created from this second dataset was found to be the relative sizes of the laser footprint and smallest grains. Copyright © 2009 John Wiley & Sons, Ltd.     

The zoogeomorphology of case-building caddisfly: Quantifying sediment use

Caddisfly (Trichoptera) larvae are an abundant and widespread aquatic insect group characterized by the construction of silk structures, including nets and cases. Case-building caddisfly have the potential to modify the sorting and mobility of sand and fine gravel via: (1) case construction, resulting in altered sediment properties; (2) transporting sediment incorporated into cases over the river bed; and (3) changing the structure of river beds via burrowing activity. To investigate these mechanisms, it is necessary to understand the mass, size distribution and spatial variability of sediment use by case-building caddisfly larvae. We quantified the mineral sediment used by individuals and communities of case-building caddisfly in 27 samples, from three sites on a gravel-bed stream. The mass and size distribution of sediment in individual cases varied between taxa (mass = 0.001–0.83 g, D₅₀ = 0.17–4 mm). The mean mass of sediment used by the caddisfly community was 38 g m⁻² and varied locally. Sediment use was predominantly coarse sand (D₅₀ = 1 mm). 64% of sediment use was attributable to Agapetus fuscipes (Glossosomatidae). Due to within-species variability in case mass, the abundance of most taxa, including A. fuscipes, was only weakly associated with the mass of sediment used by this species, at the river scale. Whilst the caddisfly community used a small percentage of the total sediment available (average 2.99% of the 1–1.4 mm size fraction), A. fuscipes used more fine sediment in their cases at sites where it was more available. Despite variability in local habitat, all sites supported diverse case-building caddisfly communities utilizing mineral sediment. Consequently, geomorphological effects of case-building caddisfly are potentially widespread. The results provide novel insights into the specific grain sizes and quantities of fine sediment used by caddisfly larvae, which represents an important step towards understanding their zoogeomorphic activities. © 2019 The Authors. Earth Surface Processes and Landforms Published by John Wiley & Sons Ltd.     

Entrainment,displacement and transport of tracer gravels

The mass and size distribution of grain entrainment per unit bed area may be measured by replacing a volume of the bed with tracer gravels and observing the mass difference before and after a transport event. This measure of spatial entrainment is relevant to any process involving size-selective exchange of sediment between transport and bed and may be directly used in calculations of sediment transport rate using an elementary relation for fractional transport components presented here. This relation provides a basis for evaluating tracer data collected by different methods and may be used to provide physical insight regarding the expected behaviour of tracer grains. The variation with grain size of total displacement length L_ti depends on the degree of mobilization of the individual fractions on the bed surface: L_ti is independent of D_i for smaller, fully mobile sizes and decreases rapidly with D_i for larger fractions in a state of partial transport (in which a portion of the surface grains remain immobile through the flow event). The boundary between fully and partially mobile grain sizes increases with flow strength. These inferences are supported by values of L_ti calculated from flume experiments and provide a physical explanation for a summary relation between L_ti and D_i based on field data. © 1997 John Wiley & Sons, Ltd.     

Regional grain size variations in aeolian sediments along the transition between Tibetan highlands and north‐western Chinese deserts – the influence of geomorphological settings on aeolian transport pathways

Sediment distribution is investigated applying grain size analysis to 279 surface samples from the transitional zone between high mountains (Qilian Shan) and their arid forelands (Hexi Corridor) in north‐western China. Six main sediment types were classified. Medium scale (10³ m) geomorphological setting is carefully considered as it may play an important role concerning sediment supply and availability. A tripartite distribution of sedimentological landscape units along the mountain to foreland transition is evident. Aeolian sediments (e.g. loess and dune sands) are widespread. They are used to identify aeolian transport pathways. The mU/fS‐ratio (5–11 µm/48–70 µm) among primary loess opposes the two grain size fractions being most sensitive to varying accumulation conditions. The first fraction is attributed to long‐distance transport in high suspension clouds whereas the latter represents local transport in saltation mode. The ratio shows strong correlation with elevation (R² = 0.77). Thus, it indicates a relatively higher far‐traveled dust supply in mountainous areas (>3000 m above sea level [a.s.l.]) compared to the foreland. The contribution of westerlies to high mountain loess deposits is considered likely. Hereby, the influence of the geomorphological setting on grain size composition of aeolian sediments becomes apparent: the contribution from distant dust sources is ubiquitous in the study area. However, the far‐distance contribution may be reduced by the availability of fine sand provided in low topography settings. Plain foreland areas support fine sand deflation from supplying river beds, allowing the formation of sandy loess in foreland areas and intramontane basins. In contrast, high mountain topography inhibits strong sand deflation into loess deposits. Eastern parts of the Hexi Corridor show higher aeolian sand occurrence. In contrast, the western parts are dominated by gravel gobi surfaces. This is attributed to higher sand supply in eastern parts provided by the Badain Jaran Desert and fluvial storages as sand sources. Copyright © 2014 John Wiley & Sons, Ltd.     

Distribution of organic carbon in bed sediments of Manoa Stream,Oahu, Hawaii

Organic carbon (OC) associated with fluvial bed sediment plays an important role in biotic and abiotic processes operating within drainage basins. Increasingly, there is a need to characterize storage and spatial distributions of OC in aquatic sediments, particularly under-sampled areas like tropical streams. The objectives of this study were to examine in detail the variation of OC concentration with bed sediment grain size, to characterize the influence of grain size variation on relative OC mass storage, and to compare weighted OC values to those in other aquatic sediments worldwide. The study area selected was a third-order dendritic drainage basin developed in a basaltic complex. Bed sediments along a 6 km section of Manoa Stream were systematically sampled every 50 m for a total of 113 sample site locations. Sediments were partitioned into six size fractions (< 2·0 mm) and OC was determined by dry combustion. Data indicate that the OC concentration increases with decreasing grain size, with the greatest values in the < 0·063 mm (silt + clay) fraction, approximately 4·6 times greater than the very coarse sand fraction (1·00–2·00 mm). Robust smoothing techniques illustrated a general decrease in OC concentration downstream for the size fractions < 0·25 mm. Bed sediments were dominated by size fractions coarser than 0·5 mm (80 per cent of the total distribution) and only about 2 per cent in the fractions less than 0·13 mm. Combining information on OC concentration per size fraction and the mass contribution of each fraction to the whole sample, it was observed that fractions coarser than 0·5 mm had eight to 12 times the storage of OC per kilogram of bed sediments than the fractions finer than 0·13 mm. Weighted OC values for Manoa Stream were on average 6·7 g-OC kg−1, and these were similar to those reported in the literature for a variety of sediments in aquatic environments, both freshwater and marine. These data provide important information on the relative mass storage of OC in bed sediments and their longitudinal patterns in a tropical fluvial environment. Copyright © 1999 John Wiley & Sons, Ltd.     

Video‐based gravel transport measurements with a flume mounted light table

The study of bedload transport processes is constrained by an inability to monitor the mass, volume and grain size distribution of sediment in transport at high temporal frequencies. Building upon a previously published design, we have integrated a high‐resolution (1392 × 1024 pixels) video camera with a light table to continuously capture images of 2–181 mm material exiting a flume. The images are continuously recorded at a rate of 15 to 20 frames per second and are post‐processed using LabView^(?) software, yielding continuous grain‐size‐specific transport information on a per second basis. The video capture rate is sufficient to record multiple images of each grain leaving the flume so that particle velocities can be measured automatically. No manual image processing is required. After calibration the method is accurate and precise for sediment in the 2 mm through to 45 mm grain size classes compared with other means of measuring bedload. Based on a set of validation samples, no statistically significant difference existed between the D₁₀, D₁₆, D₂₅, D₅₀, D₇₅, D₈₄, D₉₀ and D₉₅ determined by sieving captured samples and the D_i values determined with the system. On average the system overpredicted transport by 4 per cent (n = 206, SD = 42%). This error can be corrected easily by simply weighing the mass of sediment that leaves the flume. The technology is relatively inexpensive and provides high‐resolution data on coarse sediment transport out of a flume. Copyright © 2008 John Wiley & Sons, Ltd.     

A rational sediment transport scaling relation based on dimensionless stream power

The concept of stream channel grade – according to which a stream channel reach will adjust its gradient, S, in order to transport the imposed sediment load having magnitude Q_b and characteristic grain size D_b, with the available discharge Q (Mackin, 1948 , Geological Society of America Bulletin 59 : 463–512; Lane, 1955 , American Society of Civil Engineers, Proceedings 81 : 1–17) is one of the most influential ideas in fluvial geomorphology. Herein, we derive a scaling relation that describes how externally imposed changes in either Q_b or Q can be accommodated by changes in the channel configuration, described by the energy gradient, mean flow depth, characteristic grain size and a parameter describing the effect of bed surface structures on grain entrainment. One version of this scaling relation is based on the dimensionless bed material transport parameter (W*) presented by Parker and Klingeman ( 1982 , Water Resources Research 18 : 1409–1423). An equivalent version is based on a new dimensionless transport parameter (E*) using dimensionless unit stream power. This version is nearly identical to the relation based on W*, except that it is independent of flow resistance. Both versions of the scaling relation are directly comparable to Lane's original relation. In order to generate this stream power‐based scaling relation, we derived an empirical transport function relation relating E* to dimensionless stream power using data from a wide range of stable, bed load‐dominated channels: the form of that transport function is based on the understanding that, while grain entrainment is related to the forces acting on the bed (described by dimensionless shear stress), sediment transport rate is related to the transfer of momentum from the fluid to the bed material (described by dimensionless stream power). Copyright © 2010 John Wiley & Sons, Ltd.     

Sediment transferring function of the lower reaches of the Yellow River influenced by drainage basin factors and human activities

Since 1986, with a sharp decrease in water dis-charges, the Yellow River has entered a period charac-terized by low discharges and seasonally occurring dry-ups[1,2]. Since 1999, more strict management of water diversion has been imposed, and therefore the dry-ups have been well under control. However, the lower reaches of the Yellow River is still predominated by low-discharges, and has become a man-induced shrinking river. In the past 40 years, significant effect of soil and water conservat…     

Distribution of clay-sized sediments in streambeds and influence of fine sediment clogging on hyporheic exchange

In this work, the deposition of clay-sized fine particles (d₅₀ = 0.006 mm) and its subsequent influence on the dune-induced hyporheic exchange are investigated. Fine sand (D₅₀ = 0.28 mm), coarse sand (D₅₀ = 1.7 mm), and gravel (D₅₀ = 5.5 mm) grains were used to form homogenous model streambeds; one control - no clay input, and two treatments - increasing clay inputs for each grain type. The results indicate that the clogging profiles of clay-sized sediments may not be predicted accurately using the previously proposed metric based on the relative sizes of infiltrating and substrate sediments. Further, the depositional patterns vary with the initial concentration of clay particles in the surface water. The assessment of clogging profiles in coarse-grained model streambeds also reveals a preferential infiltration of the clay particles in the hyporheic downwelling regions. The results from the dye tracer test suggest that the accumulation of clay particles altered the exchange characteristics in the treatment flumes. For each grain size, the treatment flumes exhibit lower hyporheic flux and higher median residence times compared to their respective control flumes. The dye penetration depths were lower in treatment flumes with fine and coarse sand compared to their respective control flumes. Interestingly, higher penetration depths were observed in treatment flumes with gravel compared to their respective control flume potentially due to the generation of preferential flow paths in the partially clogged gravel beds. The clogging altered the hyporheic fluxes and residence times in the coarse-grained model beds to a greater degree in comparison to the fine sand beds. Overall, our findings indicate that the properties of both fine and substrate sediments influence the clogging patterns in streambeds, and the subsequent influence of fine sediment clogging on hyporheic exchange and associated processes may vary across stream ecosystems.     

The influence of flow discharge variations on the morphodynamics of a diffluence–confluence unit on a large river

Bifurcations are key geomorphological nodes in anabranching and braided fluvial channels, controlling local bed morphology, the routing of sediment and water, and ultimately defining the stability of their associated diffluence–confluence unit. Recently, numerical modelling of bifurcations has focused on the relationship between flow conditions and the partitioning of sediment between the bifurcate channels. Herein, we report on field observations spanning September 2013 to July 2014 of the three‐dimensional flow structure, bed morphological change and partitioning of both flow discharge and suspended sediment through a large diffluence–confluence unit on the Mekong River, Cambodia, across a range of flow stages (from 13 500 to 27 000 m³ s^?1). Analysis of discharge and sediment load throughout the diffluence–confluence unit reveals that during the highest flows (Q = 27 000 m³ s^?1), the downstream island complex is a net sink of sediment (losing 2600 ± 2000 kg s^?1 between the diffluence and confluence), whereas during the rising limb (Q = 19 500 m³ s^?1) and falling limb flows (Q = 13 500 m³ s^?1) the sediment balance is in quasi‐equilibrium. We show that the discharge asymmetry of the bifurcation varies with discharge and highlight that the influence of upstream curvature‐induced water surface slope and bed morphological change may be first‐order controls on bifurcation configuration. Comparison of our field data to existing bifurcation stability diagrams reveals that during lower (rising and falling limb) flow the bifurcation may be classified as unstable, yet transitions to a stable condition at high flows. However, over the long term (1959–2013) aerial imagery reveals the diffluence–confluence unit to be fairly stable. We propose, therefore, that the long‐term stability of the bifurcation, as well as the larger channel planform and morphology of the diffluence–confluence unit, may be controlled by the dominant sediment transport regime of the system. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

Channel flow competence and sediment transport in upland streams in southeast Australia

Bedload transport data from planebed and step‐pool reach types are used to determine grain size transport thresholds for selected upland streams in southeast Australia. Morphological differences between the reach types allow the effects of frictional losses from bedforms, microtopography and bed packing to be incorporated into the dimensionless critical shear stress value. Local sediment transport data are also included in a regime model and applied to mountain streams, to investigate whether empirical data improve the delineation of reach types on the basis of dimensionless discharge per unit width (q*) and dimensionless bedload transport (q_b*). Instrumented planebed and step‐pool sites are not competent to transport surface median grains (D_50s) at bankfull discharge (Q_bf). Application of a locally parametrized entrainment equation to the full range of reach types in the study area indicates that the majority of cascades, cascade‐pools, step‐pools and planebeds are also not competent at Q_bf and require a 10 year recurrence interval flood to mobilize their D_50s. Consequently, the hydraulic parameters of the regime diagram, which assume equilibrium conditions at bankfull, are ill suited to these streams and provide a poor basis of channel delineation. Modifying the diagram to better reflect the dominant transported bedload size (equivalent to the D₁₆ of surface sediment) made only slight improvements to reach delineation and had greatest effect on the morphologies with smaller surface grain sizes such as forced pool‐riffles and planebeds. Likewise, the Corey shape factor was incorporated into the regime diagram as an objective method for adjusting a base dimensionless critical shear stress (τ*_c50b) to account for lithologically controlled grain shape on bed packing and entrainment. However, it too provided only minor adjustments to reach type delineation. Copyright © 2007 John Wiley & Sons, Ltd.     

Threshold of coarse sediment transport in broad and narrow natural streams

The threshold of coarse sediment transport has been examined in natural streambeds in an upland Pennine (U.K.) area. Threshold values of the total boundary shear stress (T₀) (for a given grain size), in a narrow natural stream (W/D < 11) are considerably higher than values of T₀ in a broad stream (W/D > 11). Efficiency in the entrainment process is related not only to the overall channel geometry, but also varies as a function of discharge in channels characterized by compound roughness. Empirical curves relating T₀ and a mean grain size (d ₅) are presented, but are limited in application to streams of similar physical and hydraulic characteristics as the ones examined in this investigation. Considerable divergence is noted between these empirical functions and a summary empirical function for general application obtained from a published source. The reasons for this divergence are discussed. The influence of grain shape was found not to be important in the initiation of motion criterion. This conclusion may reflect the limited range of natural grain shapes in the study streams, but might reasonably apply to other field investigations of similar streams. Modifications of the Shields' and Yalin diagrams are suggested for practical applications in shallow streams with poorly-graded bed material. The Shields' parameter may be regarded as an inverse function of the relative protrusion of individual grains in the shallow flow depth (d ₅/D). The increased importance of augmented drag forces, in the entrainment process in shallow flows, is suggested as the physical explanation for the reduced values of the Shields' parameter. However, the relationships presented should not be applied to laboratory experiments concerned with well-graded sediments (therefore beds with little deviation in level), in which the Shields' parameter may be regarded as constant at high Reynolds' grain numbers. Consistent estimated field values of ?, a threshold sediment transport parameter, might be used to compare field data to threshold values derived from statistical arguments and laboratory experiments reported in the literature.