Electrical and electromagnetic surveys to locate possible causes of water seepage to ground surface at a quarry open pit near Helwan city,Egypt

Water seepage to ground surface at a limestone quarry located at Wadi Garawy about 20 km south-east of Helwan city in Egypt posed a real threat to the mining activity at the quarry. The quarry area is known to be very dry for decades and away from water utilities and infrastructures that may cause water leaks to the quarry. Geophysical investigation including 1D Vertical Electrical Sounding (VES), 2D Electrical Resistivity Tomography (ERT) and 1D Transient Electromagnetic (TEM) surveys were conducted to characterize the rock sequence and locate what could be a possible source of water seepage to the quarry. The resistivity profiles generated from the VES and TEM surveys mapped the rock units in the area down to depths exceeded 100 m. The ERT profiles acquired from the quarrying zone close to the water seepage spot have imaged the top of groundwater level at few meters below the ground surface at the quarry open pit. The spot of groundwater seepage seemed to occur at an area of limestone dissolution that were filled by finer sediments. The finer sediments acted as a hydrological conduit that allowed an upward seepage of groundwater to ground surface under the capillary action effect.     

Geophysical signatures resolving hydrogeological complexities over hard rock terrain—a study from Southern India

A series of geophysical parameters have been applied with geological perception to resolve the hydrogeological complexities over granitic terrain at Hyderabad, India. Frequent failure of borehole drillings and the thrust conditions of community have prompted a noninvasive suitable tool, applied at small scale for pinpointing potential well site. Geophysical scanning, viz. electrical resistivity tomography (ERT), spontaneous potential (SP), and electrical gradient profiling (GP) were employed within the restricted space of housing complex to obtain the true characteristics of the subsurface lithology, where anomalies by the underground utility structures have been nullified. Results showed, in ERT, the low order of resistivity range 123 to 200?Ωm showing a plume like weathered zone underlain by sudden slip of massive granite (>217?Ωm) was of great interest to proceed further in the process. Here, the switchover in SP value from +18 mV to ?17 mV and GP from mean value 10 to 90 mV/m was recorded. The anomalies in SP and GP were precisely coincided with the ERT where upcoming of subsurface massive granite next to the inferred fracture was noted. Drilling core logs satisfies the geophysical signatures ensuring the inferred saturated fracture with the total yield 1,302 gal/h.     

岩溶区页岩气勘探中的近地表地球物理探测技术应用研究

岩溶区页岩气钻井在近地表常揭露溶洞、地下河、强裂隙带等不良地质体,严重制约了页岩气资源勘探开发的进程。在岩溶页岩气靶区利用地球物理技术探测对钻探不利的近地表地质结构构造,可有效规避钻井钻遇近地表强岩溶发育带、断层破碎带的风险。综合运用高密度电阻率成像法、音频大地电磁法和测氡法对贵州都匀和广西融安碳酸盐岩区的2个油气靶区进行了地下构造识别,结果表明：高密度电阻率成像法和音频大地电磁法能有效确定浅地表地下低阻构造的位置、宽度和产状,高密度电阻率成像法在50 m以浅深度拥有更高的分辨率,音频大地电磁法探测深度更深,但对地下介质的分辨率不高,氡气测量能很好地识别地下低阻构造的属性。高密度电阻率成像法、音频大地电磁法与测氡法三者可优势互补,组成有效识别岩溶区近地表地质结构构造的技术方法体系,可为南方岩溶区页岩气钻井避开近地表强岩溶发育带、断层破碎带以及最终位置的确定提供可靠的技术支撑。     

高密度电法与微动技术组合在岩溶塌陷分区中的应用分析——以广西来宾吉利塌陷为例

为了验证物探技术在岩溶塌陷调查中的应用效果,本文于广西来宾市吉利村开展了高密度电法和微动技术野外探测研究。结果表明:高密度对称四极电测深能直观地反映第四系覆盖层的厚度和低阻异常的深度,微动技术能定性地判定地下暗河和岩溶破碎带在地表的平面投影,将两种方法相结合能更加准确地圈出塌陷,以及引起塌陷的溶洞、地下河、断层破碎带及软土分布范围。地下暗河或岩溶破碎带在高密度联合剖面法上反映为低阻正交点异常,极距为45 m时正交点附近电阻率值约为250 Ω?m;在微动H/V比值谱上反映为H/V极大值异常,极大值特征频率在2~6 Hz之间。依据2测线上的高密度电法和微动异常显示,圈出了两个易塌陷区,经对其中的一异常进行钻探验证,异常区覆盖层下42 m 厚的灰岩地层中钻遇溶洞8个,其中最大的高达5.7 m。      

The effect of the Messinian Deep Stage on karst development around the Mediterranean Sea. Examples from Southern France

It is difficult to explain the position and behaviour of the main karst springs of southern France without calling on a drop in the water table below those encountered at the lowest levels of Pleistocene glacio-eustatic fluctuations. The principal karst features around the Mediterranean are probably inherited from the Messinian period (“Salinity crisis”) when sea level dropped dramatically due to the closing of the Straight of Gibraltar and desiccation of the Mediterranean Sea. Important deep karst systems were formed because the regional ground water dropped and the main valleys were entrenched as canyons. Sea level rise during the Pliocene caused sedimentation in the Messinian canyons and water, under a low hydraulic head, entered the upper cave levels.

The powerful submarine spring of Port-Miou is located south of Marseille in a drowned canyon of the Calanques massif. The main water flow comes from a vertical shaft that extends to a depth of more than 147 m bsl. The close shelf margin comprises a submarine karst plateau cut by a deep canyon whose bottom reaches 1,000 m bsl. The canyon ends upstream in a pocket valley without relation to any important continental valley. This canyon was probably excavated by the underground paleoriver of Port-Miou during the Messinian Salinity Crisis. Currently, seawater mixes with karst water at depth. The crisis also affected inland karst aquifers. The famous spring of Fontaine de Vaucluse was explored by a ROV (remote observation vehicle) to a depth of 308 m, 224 m below current sea level. Flutes observed on the wall of the shaft indicate the spring was formerly an air-filled shaft connected to a deep underground river flowing towards a deep valley. Outcroppings and seismic data confirm the presence of deep paleo-valleys filled with Pliocene sediments in the current Rhône and Durance valleys. In the Ardèche, several vauclusian springs may also be related to the Messinian Rhône canyon, located at about 200 m below present sea level. A Pliocene base level rise resulted in horizontal dry cave levels. In the hinterland of Gulf of Lion, the Cévennes karst margin was drained toward the hydrologic window opened by the Messinian erosional surface on the continental shelf.     

Integrated application of 2D resistivity and electromagnetic methods to investigate a metallic-sulfide deposit in Soap Gulch,Montana. A case study

Geoelectrical methods involving electrical resistivity tomography (ERT), self-potential (SP), frequency domain electromagnetic (FDEM), and very low frequency (VLF) methods have been used to provide valuable information in locating a known sulfide ore body in Soap Gulch, Montana. The study develops basis of comparison for the geophysical techniques employed. Ranges of resistivity along the area have been established using interpreted ERT which can help to understand the subsurface distribution of sulfides in the area. A sulfide body was delineated from the survey area corresponding to anomalously low resistivity values on the ERT section, negative SP, and high apparent current density zone in VLF. Depth to the localized ore zone ranges approximately from 10 to 20 m. FDEM data reflect the conductivity distribution of the shallow subsurface (less than 6 m deep); hence, the delineated sulfide zone had minimal contribution to FDEM measurements. The results of the study show that SP, VLF, and ERT methods provide significant information in localizing ore bodies. The survey revealed that the resistivity values obtained from ERT profile corroborate the FDEM, SP, and VLF from the area.     

Ground penetrating radar and 2D electric resistivity studies for tracing hydrocarbon leakage site,close to Abha City: a case study

This work presents the application of the ground-penetrating radar (GPR) method and electric resistivity tomography (ERT) technique in outlining a zone of contamination due to the light non-aqueous phase liquid (LNAPL) plume underground in the area of an impacted fuel station, close to Abha City. The GPR has been performed using SIR3000 unit with the 100 and 400 MHz antennas. The main objective of the GPR survey was to evaluate the lateral extension of contamination. The complex GPR signature of the plume was well characterized. Low reflectivity zone corresponds to hydrocarbon vapor phase in the vadose zone. Enhanced reflections are associated with free and residual products in the fractured saturated zone directly above the water table. An electric resistivity tomography (ERT) survey was performed on four profiles within the site to investigate the vertical and horizontal extent of the contamination plume and to define the bottom of the landfill. The 2D electric profiles show the presence of low-resistivity (4O to 37 Ω m) anomalies that refers to the presence of accumulated hydrocarbons. From the interpretation of the GPR and ERT profile, it was possible to locate the top and bottom of the contamination plume of the waste disposal site. The radar signal penetrated deep enough and enabled the identification of a second reflector at approximately 10-m deep, interpreted as the hard basement surface which causes the strong amplitude reflection in the GPR profile. The results of GPR and ERT showed good agreement.     

Mise-a-la-masse method,tracer tests and cave detection analysis of underground-river karst-conduit distribution and structure: a case study of the Dafengdong conduits in Guizhou Province,China

In karst areas, groundwater movement is dominated by conduit flow; thus, understanding the distribution and structure of karst conduits has great significance for water research, groundwater protection and engineering construction. With the Dafengdong (Guizhou Province, China) underground river karst as an example, a mise-a-la-masse method, tracer tests and cave detection were conducted to study the distribution and structure of karst conduits. Combined with information on the geological and hydrogeological conditions, the geological factors that form karst conduits were determined. It can be concluded that: (1) Under the influence of faults, karst conduits usually develop towards or along faults; (2) multiple karst conduits form easily on both sides of tectonic fracture zones; (3) both lithology and geological structure affect the formation of blue holes, and when the directions of karst conduits change, blue holes easily form in weak parts of the structure; (4) at springs where two aquifers intersect, with strong chemical dissolution of the lower karst aquifer and mechanical collapse of the upper aquifer, blue holes also form easily; and (5) integrated mise-a-la-masse method, tracer tests and cave detection can accurately discern the distribution and structure of karst conduits. Geological factors can be used to preliminarily delineate the distribution and structure of karst conduits in similar areas based on hydrogeological conditions. Such methods hold great significance for groundwater extraction and protection and engineering construction in karst areas.

     

桂南红层岩溶及其发育控制因素探讨

桂南红层岩溶形态主要表现为岩溶缓丘、地下溶洞、岩溶泉以及地下河、天窗等。在地下50m深度范围,溶洞高0.5～3m,多为无充填溶洞,发育数量随深度增加而减少。岩溶泉类型有上升泉和下降泉,泉水流量变化较大。目前尚未发现仅由红层作为含水层的地下河。桂南红层岩溶的发育程度及形态特征与岩性、构造及水文地质条件有关。红层岩溶主要发育于红层盆地边缘的钙质砾岩中。红层的层组结构可分为单一型和互层型,单一型岩溶发育相对强烈,互层型以岩溶顺层发育为特征。通常,在可溶岩与非可溶岩接触带附近红层溶洞发育;在断裂破碎带以及河谷地带红层岩溶发育强烈,溶洞规模较大。      

Imaging fracture distributions of the Al-Khuff Formation outcrops using GPR and ERT geophysical techniques,Al-Qassim area,Saudi Arabia

Khuff Formation is of utmost importance in Saudi Arabia for oil and gas reservoir although it is composed mainly of limestone. This reason refers to the existence of intensive fractures which play a vital role in the increase in porosity and permeability of this formation. The fracture pattern in the study area was verified through 2D and 3D ground penetrating radar (GPR)-defined and electrical resistivity tomography (ERT)-defined surveys. In this respect, ten of 2D GPR surveys were collected along an intersected grid of profiles covering the study area while ERT data were collected along three profiles of the GPR grid. The results were interpreted in light of the field-based structural and stratigraphic assessment of the outcropping rocks. The analysis of the inverted ERT and filtered GPR sections revealed the presence of fractures. Several resistivity and electromagnetic reflection anomalies were laterally and vertically identified across the measured sections clarifying fractures that extend to a depth of 24 m in the limestone. Most fractures are oriented vertical to sub-vertical dipping both east-west and north-south.     

Application of electrical resistivity tomography (ERT) technique to detect underground cavities in a karst area of South Korea

Recently, the electrical resistivity tomography (ERT) technique has been increasingly applied to underground cavity detection filled with groundwater and/or clay. In this study, an ERT survey was conducted to examine the spatial distribution and shape of underground cavities in a karst area in Korea. Numerical ERT modeling and inversion were carried out to select appropriate field survey parameters. Two geological structures, similar to those that exist in the field survey area, were modeled: a sinkhole model and a vein-type structure. Electrode configurations using pole–pole, pole–dipole, dipole–pole, and dipole–dipole arrays were tested with the two geologic models and compared. The numerical modeling showed that the resistivity distribution of the ERT tomogram using the pole–dipole array produced the best representation of the two models. The pole–dipole and pole–pole array configurations were applied in an ERT field survey using six boreholes. The field ERT results show that cavity areas filled with clay or groundwater appeared as low-resistivity anomalies in the limestone formation. This was particularly evident in the inclined vein-type structures attributed to fracture zones, where the field data were similar to the modeling results. Therefore, the ERT technique could be effectively used for detecting underground limestone cavities under similar geological conditions as those at our study area.     

Strategic groundwater resources in the Tagliamento River basin (northern Italy): hydrogeological investigation integrated with geophysical exploration

The western sector of the Tagliamento River basin (Friuli Venezia-Giulia Region; northern Italy) is characterized by important water resources, both superficial and underground. In particular, in the Quaternary deposits of the plain, up to a depth of 500 m, six artesian aquifer systems exist. A large amount of lithological, geomorphological, and hydrogeological data is presented, allowing for definition of (a) the principal aquifer system of the area to a depth of about 500 m; (b) geometrical characteristics of the aquifers (thickness, lateral extension, etc); (c) the hydraulic parameters (hydraulic conductivity, transmissivity); (d) chemico-physical characteristics of the water; and (e) vulnerability to pollution of the aquifer systems. In a test area, where many boreholes were drilled for fresh water supply, the conceptual hydrogeological model was integrated by a detailed and repeated three-dimensional (3D) resistivity survey using combined electrical resistivity tomography (ERT) and time-domain electromagnetic (TDEM) soundings. ERT investigation was mainly used to get detailed information about geometry and porosity of the overburden and to calibrate the shallowest TDEM information.     

3D modeling and monitoring of karst system as a base for its evaluation and utilization: a case study from eastern Serbia

Beljanica Mountain in eastern Serbia is a part of the Carpathian Balkan arch (northern Alpine branch). It covers an area of about 300 km² and consists mostly of Jurassic and Cretaceous limestones. Numerous surface karst features, long caves and several large karstic springs located in Beljanica’s piedmont along the contact of karstic and non-karstic rocks are all indicators of an intense karstification. Currently, the large karstic water reserves of Beljanica Mountain are not properly utilized because of their distance from main consumers, the objection by national water managers that the springs lack a stable and sufficient discharge particularly during recession periods. Due to its unpolluted and high quality water, the area is a great prospect for future water supply, and provides an opportunity for artificial regulation and for the design and implementation of specific tapping structures. This paper includes an analysis of the created 3D ArcGIS model of karst interior and its correlation with historical and newly collected data of spring discharges and groundwater physico-chemical characteristics. The results of karst aquifer monitoring (both quantitative and qualitative) are linked with the results of extensive field geological and speleological survey of the upper non-saturated part of the karst (such as sinkholes, pits and caves) and with the investigation of the permanently saturated deeper part of the aquifer (including the diving methods). The model of karst interior is based on the data from the 69 caves, 15 sinks and 1,682 dolines (sinkholes) surveyed. The total length of the karst channels network, calculated using the GIS model and presented in a 3D environment, is 647 km. The catchment areas of five major springs that drain the areas are estimated to range from only 7 km² (Malo Vrelo Spring) to 124 km² (Vrelo Mlave Spring). The groundwater exploitable reserves of Beljanica karst aquifer are estimated to be over 4 m³/s. The waters are low mineralized, unpolluted and have a great potential for water supply.     

River–groundwater connectivity in a karst system,Wellington, New South Wales,Australia

The characterization of river–aquifer connectivity in karst environments is difficult due to the presence of conduits and caves. This work demonstrates how geophysical imaging combined with hydrogeological data can improve the conceptualization of surface-water and groundwater interactions in karst terrains. The objective of this study is to understand the association between the Bell River and karst-alluvial aquifer at Wellington, Australia. River and groundwater levels were continuously monitored, and electrical resistivity imaging and water quality surveys conducted. Two-dimensional resistivity imaging mapped the transition between the alluvium and karst. This is important for highlighting the proximity of the saturated alluvial sediments to the water-filled caves and conduits. In the unsaturated zone the resistivity imaging differentiated between air- and sediment-filled karst features, and in the saturated zone it mapped the location of possible water- and sediment-filled caves. Groundwater levels are dynamic and respond quickly to changes in the river stage, implying that there is a strong hydraulic connection, and that the river is losing and recharging the adjacent aquifer. Groundwater extractions (1,370 ML, megalitres, annually) from the alluvial aquifer can cause the groundwater level to fall by as much as 1.5 m in a year. However, when the Bell River flows after significant rainfall in the upper catchment, river-leakage rapidly recharges the alluvial and karst aquifers. This work demonstrates that in complex hydrogeological settings, the combined use of geophysical imaging, hydrograph analysis and geochemical measurements provide insights on the local karst hydrology and groundwater processes, which will enable better water-resource and karst management.     

Hydrogeological properties of fault zones in a karstified carbonate aquifer (Northern Calcareous Alps,Austria)

This study presents a comparative, field-based hydrogeological characterization of exhumed, inactive fault zones in low-porosity Triassic dolostones and limestones of the Hochschwab massif, a carbonate unit of high economic importance supplying 60 % of the drinking water of Austria’s capital, Vienna. Cataclastic rocks and sheared, strongly cemented breccias form low-permeability (<1 mD) domains along faults. Fractured rocks with fracture densities varying by a factor of 10 and fracture porosities varying by a factor of 3, and dilation breccias with average porosities >3 % and permeabilities >1,000 mD form high-permeability domains. With respect to fault-zone architecture and rock content, which is demonstrated to be different for dolostone and limestone, four types of faults are presented. Faults with single-stranded minor fault cores, faults with single-stranded permeable fault cores, and faults with multiple-stranded fault cores are seen as conduits. Faults with single-stranded impermeable fault cores are seen as conduit-barrier systems. Karstic carbonate dissolution occurs along fault cores in limestones and, to a lesser degree, dolostones and creates superposed high-permeability conduits. On a regional scale, faults of a particular deformation event have to be viewed as forming a network of flow conduits directing recharge more or less rapidly towards the water table and the springs. Sections of impermeable fault cores only very locally have the potential to create barriers.     

Imaging of wastewater percolation in heterogeneous soil using electrical resistivity tomography (ERT): a case study at east of Tenth of Ramadan City,Egypt

The objective of this study is to evaluate the effectiveness of DC resistivity surveys for imaging the wastewater percolation around the stabilization ponds in the Tenth of Ramadan City, the desert fringes of East Nile Delta, Egypt. Detailed resistivity surveys, including DC soundings and electrical resistivity tomography (ERT), were carried out along several profiles. Furthermore, synthetic modeling of ERT was designed to optimize the survey configurations and interpretation of the results. A 2D modeling of smoothness-constrained least-squares inversion scheme was applied to delineate the possible wastewater infiltration zones from oxidation ponds. Because the geoelectrical interpretation has a degree of non-uniqueness, the resistivity inversion was constrained using borehole lithological information and soil sample laboratory measurements. The DC inversion results indicate decreasing resistivity down to a depth of 15 m around waste disposal sites. The inferred soil zone close to the oxidation ponds was a mixture of sand, silt and clay. Moreover, the clay minerals were characterized by moderate swelling that could have reduced the vertical infiltration speed, causing wastewater seepage, especially around unlined disposal sites and open surface drains. Accordingly, the medium-to-low resistivity values can be attributed to wastewater leakage in clayey sand soil. Because the area slopes generally toward the northeast, the surface seepage was dominant in the shallow impermeable sandy clay subsoil. Therefore, measuring soil parameters is a complementary method to optimize resistivity interpretation, with potential for mitigating environmental hazards from wastewater leakage around disposal ponds.     

Geophysical prediction and following development sinkholes in two Dead Sea areas, Israel and Jordan

Geophysical methods—seismic refraction (SRFR), electrical resistivity tomography (ERT), and microgravity—were applied to the Dead Sea (DS) sinkhole problem in the Ein Gedi area at the earlier stage of the sinkhole development (1998–2002). They allowed determining the sinkhole formation mechanism and localizing the sinkhole hazardous zones. The SRFR method permitted to delineate the underground edge of a salt layer at the depth of 50 m. The salt edge was shaped like the sinkhole line on the surface. It was concluded that the sinkhole development is linked to the salt edge. Geoelectrical quasi-3D mapping based on the ERT technique detected large resistivity anomalies with 250–300 m² diameter and 25–35 m deep. The Ein Gedi area has been also mapped by the use of Microgravity method. The residual Bouguer gravity anomaly map shows negative anomalies arranged along the edge of the salt layer. Those gravity anomalies overall are very similar in plan to the resistivity distribution in this area. The results of forward modeling indicate that both high resistivity and residual gravity anomalies are associated with a subsurface decompaction of the soil mass and deep cavity at the sinkhole site. Following monitoring of the sinkhole development carried out by the Geological Survey of Israel confirmed our suggestions. The drilling of numerous boreholes verified the location of the salt edge. Geographical Information System (GIS) database testifies that during 2003–2009 new sinkholes are continuing to develop along the salt edge within a narrow 50–100 m wide strip oriented approximately in north–south direction (slightly parallel to the shoreline). No promotion in west–east direction (perpendicularly to the DS shoreline) was observed in Israel. Collapse of sinkholes and their clustering have been occurred within the area of high resistivity anomaly and negative residual gravity anomaly. Similar studies carried out at the Ghor Al-Haditha area (Jordan) have shown that sinkholes there are also arranged along the winding line conforming to the salt edge. In this area sinkholes are slowly moved to the Dead Sea direction. Results of geophysical studies in numerous DS sites indicate similar sinkhole development. It allowed generating of the sinkhole formation model based on ancient (10,000–11,000-year old) salt belt girding the Dead Sea along its shores     

Alimentation et origine de la salinité de la source sous-marine de Port-Miou (Marseille–Cassis). Principale émergence d'un réseau karstique hérité du Messinien

(Marseille–Cassis–Bouches–du-Rhône). The salinity of the karstic submarine spring of Port-Miou has sometimes been attributed to the leaching of continental evaporites. Our recent chemical and isotopic analyses indicate a simple mixing between fresh karstic water and seawater. In the main gallery, the contamination by seawater, still present up to 2.2 km from the entrance at a depth of 147 m below the sea level, forces us to think about a general geometry that allows mixing of waters, at a great depth, in the karstic system. The measurements of the discharge of the spring indicate an excess of water compared with its supposed watershed, whereas a succinct evaluation of the aquifers of the Lower Provence indicates a deficit of discharge. Consequently, it seems possible that parts of the calcareous areas of the Lower Provence feed the springs of Port-Miou with a total catchment area of 1200 km². This deep and large karstic system was probably installed during the Messinian period, when the important lowering of the level of the Mediterranean Sea provoked an important gradient between Provence and the seashore. To cite this article: B. Blavoux et al., C. R. Geoscience 336 (2004).     

Military training area in Kras (Slovenia)

 Slovenia's main military training area at Poček is located in the mountainous Javorniki Watershed. This is a karstic district without surface drainage or river valleys. The typical landscapes are conical hills and plateaus with many dolines. The lithology, tectonic structure and speleological data indicate a typical karst aquifer with underground water moving rapidly through fissures and conduits. Little attenuation occurs in such conditions and as a result there is a high risk of pollution. Tracer tests have shown that a significant proportion of the water recharging the Malni and Vipava springs comes from the vicinity of the military training area. As a result any polluting activities taking place within the military training area are likely to affect the two springs. This is a very serious matter as the springs have been developed to provide the water supply for the population of south-western Slovenia. Received: 20 April 1998 · Accepted: 24 August 1998     

An integrated approach to investigate saline water intrusion and to identify the salinity sources in the Central Godavari delta, Andhra Pradesh, India

The Central Godavari delta is located along the Bay of Bengal Coast, Andhra Pradesh, India, and is drained by Pikaleru, Kunavaram and Vasalatippa drains. There is no groundwater pumping for agriculture as wells as for domestic purpose due to the brackish nature of the groundwater at shallow depths. The groundwater table depths vary from 0.8 to 3.4 m and in the Ravva Onshore wells, 4.5 to 13.3 m. Electrical Resistivity Tomography (ERT) surveys were carried out at several locations in the delta to delineate the aquifer geometry and to identify saline water aquifer zones. Groundwater samples collected and analyzed for major ions for assessing the saline water intrusion and to identify the salinity origin in the delta region. The results derived from ERT indicated low resistivity values in the area, which can be attributed to the existence of thick marine clays from ground surface to 12–15 m below ground level near the coast and high resistivity values are due to the presence of coarse sand with freshwater away from the coast. The resistivity values similar to saline water <0.01 Ω m is attributed to the mixing of the saline water along surface water drains. In the Ravva Onshore Terminal low resistivity values indicated up coning of saline water and mixing of saline water from Pikaleru drain. The SO ₄ ^?2 /Cl^?and Na⁺²/Cl^?ratios did not indicate saline water intrusion and the salinity is due to marine palaeosalinity, dilution of marine clays and dissolution of evaporites.