等离子体发射光谱法测定重晶石中钡铁和硅

重晶石经Ｎａ２ＣＯ３熔融,水浸取,过滤。沉淀经ＨＣｌ溶解后,用电感耦合等离子体发射光谱法同时测定主成分ＢａＳＯ４和次量成分Ｆｅ２Ｏ３以及滤液中的ＳｉＯ２,结果与部颁标准方法符合。方法精密度好,主量组分ＢａＳＯ４测定的ＲＳＤ（ｎ＝６）为０．２４％,次量组分Ｆｅ２Ｏ３和ＳｉＯ２的ＲＳＤ（ｎ＝６）分别是３．６９％和１．４５％。     

等离子体发射光谱法同时测定大洋富钴结壳中硅锰铁钙镁铝钛

大洋富钴结壳试样经ＨＣｌ＋ＨＮＯ３＋ＨＦ溶解,在０．２ｍｏｌ／ＬＨＦ和０．１３ｍｏｌ／ＬＨ３ＢＯ３介质中,用感耦等离子发射光谱法同时测定Ｓｉ、Ｍｎ、Ｆｅ、Ｃａ、Ｍｇ、Ａｌ、Ｔｉ元素的含量。方法经国家标准物质ＧＢＷ０７２４９大洋多金属结核验证,其结果与标准值相符,精密度ＲＳＤ〈３．２％（ｎ＝６）;已应用于太平洋富钴结壳中多元素分析。     

西阿尔卑斯Dora Maira地块含柯石英白片岩的稳定同位素地球化学与相平衡

用氧同位素温度计测定了西阿尔卑斯ＤｏｒａＭａｉｒａ地块含柯石英—镁铝榴石白片岩的峰期变质温度。石英（柯石英较变后）的δ￣（１８）Ｏ（８．１‰～８．６‰，ｎ＝６），多硅白云母的（６．２‰～６．４‰，ｎ＝３）、蓝晶石的（６．１‰，ｎ＝２）、石榴石的（５．５‰～５．８‰，ｎ＝９）、ｅｌｌｅｎｂｅｒｇｅｒｉｔｅ的（６；３‰，ｎ＝１）和金红石的（３。３‰～３．６‰，ｎ＝３）δ￣（１８）Ｏ（ＳＭＯＷ）值反映了同位素平衡。以石英—石榴石—金红石分馏为基础测定的温度为７００～７５０℃。以对压力敏感的反应：镁铝榴石＋朽石英＝蓝晶石十顽火辉石为依据确定的最小压力为３．１～３．２ＧＰａ。为了通过对温度敏感的脱水反应：滑石十蓝晶石＝镁铝榴石十柯石英十水，来稳定镁铝榴石和柯石英，在７００～７５０℃时，α（Ｈ＿２Ｏ）必须减小到０．４～０。７５。当镁铝榴石在ｘ（ＣＯ＿２）＞０．０２（Ｔ＝７５０℃，Ｐ＝３．０ＧＰａ）不稳定时，α（Ｈ＿２Ｏ）的减少不会是由于ＣＯ＿２的稀释所引起的。当缺乏较多的外来流体稀释剂（即ＣＨ＿４或Ｎ＿２时，就需要有熔体相）。在α（Ｈ＿２Ｏ）＝１．Ｏ时，花岗岩的固相线温度为６８０℃／３．０ＧＰａ，在α（Ｈ＿２Ｏ）＝０．     

氢化物—原子荧光法测定岩石中痕量硒的干扰及消除

用ＨＦ－ＨＣｌＯ４－ＨＮＯ３混合酸分解样品，采用Ｆｅ＾３＋作释放剂，研究了不同量的Ｆｅ＾３＋与ＨＣｌ酸度对Ｓｅ荧光强度的影响和干扰离子消除的效果，以及Ｆｅ＾３＋存在Ｔｅ存在下对Ｓｅ测定的影响。方法的检出限为０．０１μｇ／ｇ．样品中Ｓｅ量为０．１μｇ／ｇ的相对标准偏差（ｎ＝１１）是５．４％。用于岩石标样中痕量Ｓｅ的测定，结果较好。     

一种新型高效复合消毒剂：二氧化氯消毒剂

一种新型高效复合消毒剂：二氧化氯消毒剂虞承伟（地质矿产部山西省中心实验室）１ＣｌＯ＿２为强氧化剂在酸性条件下，ＣｌＯ＿２有很强的氧化性：ＣｌＯ＿２＋４Ｈ￣＋＋５ｅ＝Ｃｌ￣－＋Ｈ＿２Ｏ在水处理条件下（ｐＨ＝７），ＣｌＯ＿２＋ｅ＝，Ｅ＿０＝０．９５Ｖ＋２...     

甲基异丁基甲酮萃取－石墨炉平台原子吸收法测定地质样品中痕量硒和碲

样品经ＨＮＯ＿３－ＨＦ－ＨＣｌＯ＿４分解，在５．４ｍｏｌ／Ｌ的ＨＣｌ介质中，以抗坏血酸为还原剂用甲基异丁基甲酮同时萃取样品中的Ｓｅ、Ｔｅ。以Ｐｄ和Ｎｉ作混合基体改进剂，使用自制的涂锆石墨平台直接测定有机相中的Ｓｅ、Ｔｅ。方法的检出限分别为０．２１×１０￣（－９）ｇＳｅ，０．１３×１０￣（－９）ｇＴｅ；测定０．０６ｇＳｅ、０．０３ｇＴｅ的ＲＳＤ（ｎ＝１１）分别为７．０％和８．９％。     

电感耦合等离子体—发射光谱法测定大气颗粒物中的铜,铅,锌

将样品滤膜一起用ＨＦ、ＨＮＯ３及ＨＣｌＯ４消化，制成１０％的ＨＮＯ３溶液，用ＩＣＰ－ＡＥＳ测定Ｃｕ，Ｐｂ，Ｚｎ。检出限分别为１．４、８．１、０．７，ＲＳＤ％分别为３．７、７．３、１．８，已用于测定青岛市区的大气颗粒物样品。     

西藏南迦巴瓦峰地区发现的星叶石

在西藏境内喜马拉雅山脉的东端的南迦巴瓦峰地区发现了星叶石。该矿物产出于火成碳酸岩脉中，与白云石、方解石、镁橄榄石、镁铝尖晶石、金云母、韭闪石、磷灰石、镁钛矿、石榴石以及三种未定名副矿物共生。该矿物的晶胞参数为：ａ０＝５．３５６（１），ｂ０＝１１．６０７（４），ｃ０＝１１．８５１（６），α＝６４．５７°（３），β＝７６．９８°（４），γ＝８５．４５°（３）。化学成分（％）为：ＳｉＯ２３５．２２，ＴｉＯ２１１．４７，Ａｌ２Ｏ３１．１８，ＦｅＯ２８．９０，ＭｎＯ５．１５，ＭｇＯ１．５１，ＣａＯ１．７５，Ｋ２Ｏ５．９０，Ｎａ２Ｏ２．４６，总和９３．５４％，化学式为：（Ｋ，Ｎａ）３（Ｆｅ，Ｍｎ，Ｍｇ，Ｃａ）７Ｔｉ２Ｓｉ８Ｏ２４（Ｏ，ＯＨ）７。     

湖南石门雄黄矿床流体包裹体地球化学特征

石门超大型雄黄矿床流体包裹体丰富。包裹体液相成分中富Ｎａ＋、Ｃｌ－和Ｋ＋、ＳＯ２－４，气相成分中Ｈ２Ｏ占绝对优势，少量ＣＯ２，成矿流体化学类型属Ｃｌ ＳＯ４ Ｎａ Ｋ型水。雄黄、雌黄形成于低温（１８０～９０℃）、低压（２０～５ＭＰａ）、浅成（１７５～７００ｍ）、弱酸性（ｐＨ：４．６７、４．４３）和弱还原（Ｅｈ：－０．２６５Ｖ）条件。流体包裹体氢氧同位素研究表明，成矿流体主要为古大气降水，并混有盆地建造水，大气降水下渗、循环、加热、淋滤形成了中－低盐度［ｗ（ＮａＣｌ）：１６．０３％～４．２７％］，中等密度（０．８６３～１．０６５ｇ／ｃｍ３），含矿地下热水。     

原子荧光光谱法测定铜矿中硒和碲

介绍了铜矿中Ｓｅ，Ｔｅ的测定方法，样品经ＨＮＯ３－ＨＣｌＯ４分解，以含ＨＣｌＯ４的０．２ｍｏｌ／ＬＨＣｌ溶液通过７４３型阳离子树脂分离Ｃｕ，原子荧光光谱法测定Ｓｅ，Ｔｅ。     

Wavelength-dispersive X-ray fluorescence spectrometric determination of Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites

Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.     

硅酸盐类样品中硅、铁、铝、钛、锰、钙、镁、钾、钠和磷的x射线荧光光谱测定

本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。     

高压微波消解法测定醋酸纤维过滤器采集的微尘粒子中的砷镉钴铬铜铁锰镍铅钒锌

最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提     

Isotopic systematics of He,Ar, S,Cu, Ni,Re, Os,Pb, U,Sm, Nd,Rb, Sr,Lu, and Hf in the rocks and ores of the Norilsk deposits

This paper reports the first results of a study of 11 isotope systems (³He/⁴He, ⁴⁰Ar/³⁶Ar, ³⁴S/³²S, ⁶⁵Cu/⁶³Cu, ⁶²Ni/⁶⁰Ni, ⁸⁷Sr/⁸⁶Sr, ¹⁴³Nd/¹⁴⁴Nd, ^206–208Pb/²⁰⁴Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.     

Viscous, cohesive, non-Newtonian, depositing, radial slurry flow

Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.     

硅酸盐中铁、锰、钛、钙、钾、磷、硅、铝、镁、钠、锶、铷、钡的X-射线荧光光谱定量测定

本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。     

Bellechester,Minnesota, USA,lagoon collapses

Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×10⁶ 1 of partially treated effluent and about 600 m³ of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.     

Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA

The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.     

滇东南花岗岩与锡、银、铜、铅、锌多金属矿床的成因关系

滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.     

岩石密度和超高压岩石折返速率

在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。