Calibration of the high-pressure cohesive strength meter (CSM)

Coastal erosion is an immense economic and social problem that has been receiving increased attention in recent years. A number of devices have been developed to determine the sediment stability in coastal areas: laboratory and field flumes; a range of different erosion devices; shear vanes and fall cone penetrometers. The cohesive strength meter (CSM) erosion device was developed to determine in situ the temporal and spatial variations in the erosion threshold of muddy intertidal sediments. Technological developments have enabled considerable improvements to be made to the original design over the last 15 years.     

A new portable in situ flume for measuring critical shear stress on river beds

A new portable in situ flume(PISF)for measuring critical bed shear stress(CBSS)was developed in this study.The PISF consists of an open bottom sediment erosion chamber and an electrically-driven pump.Unlike most existing in situ flumes with similar designs,the new PISF does not rely on monitoring the flow conditions or particle density in the sediment erosion chamber;instead,it is a pre-calibrated flume.The calibration was performed by first determining CBSS of various selected sediment samples of known particle size and density(using the law of the wall),based on flow velocity-depth profiles measured in a 6 m straight open-channel flume using a Particle Image Velocimetry(PIV)system.These same particles of known CBSS were then used in the new in-situ flume under controlled lab conditions to obtain a series of calibration curves of CBSS vs.pump electrical power.A wide variety of particle types and sizes(simulated sediments)were used in this two-step calibration procedure to widen CBSS measurement range and simulate cohesive force effects.The size of the PISF is much smaller and more practical than other similar devices as lamellar flow conditions are not required and it can be applied to a wide range of sediment types including cohesive sediments.     

Closure relations for mobile bed debris flows in a wide range of slopes and concentrations

Debris flows are flows of water and sediment driven by gravity that initiate in the upper part of a stream, where the slope is very steep, allowing high values of solid concentration (hyperconcentrated flows), and that stop in the lower part of the basin, which is characterized by much lower slopes and reduced speeds and concentrations. Modelling these flows requires mathematical and numerical tools capable of simulating the behavior of a fluid in a wide range of concentrations of the solid phase, spanning from hyperconcentrated flows to flows in the fluvial regime. According to a two-phase approach, the depth integrated equations of mass and momentum conservation for water and sediments, under the shallow water hypothesis, are employed to solve field problems related to debris flows. These equations require suitable closure relations that in this case should be valid in a very wide range of slopes. In the hypothesis of absence of cohesive material, we derived these closure relations properly combining the relative relations valid separately in the fluvial and in the hyperconcentrated regimes. In the intermediate regime, the shear stress is due to the combined effect of the deformation of the liquid phase (grain roughness turbulence) and of inter-particle collisions. Therefore, an approach based on the sum of the effects of the two causes has been proposed, combining the Darcy–Weisbach equation and the Bagnoldian grain-inertia theory.A similar treatment has been made for the transport capacity relations, combing the Bagnold expression of the collisional regime with a transport capacity monomial formula valid in the fluvial regime.The closure relations are expressed in non-dimensional form as a function of the Froude number, of the solid concentration, of the relative submergence, and of the slope.In order to test the closure relation, a set of experiments with mixtures of non-cohesive sediments and water have been carried out in a laboratory flume under steady uniform flow conditions, with different solid and liquid discharges and different grain size distributions. The closure equations are satisfactorily tested against experimental investigation.     

Sediment mobility in response to tidal and wind-driven flows along the Belgian inner shelf,southern North Sea

The effect of hydro-meteorological forcings (tidal and wind-induced flows) on the transport of suspended particulate matter (SPM), on the formation of high-concentrated mud suspensions and on the occurrence of sand–mud suspensions has been studied using long-term multi-parametric observations. Data have been collected in a coastal turbidity maximum area (southern North Sea) where a mixture of sandy and muddy sediments prevails. Data have been classified according to variations in subtidal alongshore currents, with the direction of subtidal flow depending on wind direction. This influences the position of the turbidity maximum; as such also the origin of SPM. Winds blowing from the NE will increase SPM concentration, whilst SW winds will induce a decrease. The latter is related to advection of less turbid English Channel water, inducing a shift of the turbidity maximum towards the NE and the Westerschelde estuary. Under these conditions, marine mud will be imported and buffered in the estuary. Under persistent NE winds, high-concentrated mud suspensions are formed and remain present during several tidal cycles. Data show that SPM consists of a mixture of flocs and locally eroded sand grains during high currents. This has implications towards used instrumentation: SPM concentration estimates from optical backscatter sensors will only be reliable when SPM consists of cohesive sediments only; with mixtures of cohesive and non-cohesive sediments, a combination of both optical and acoustic sensors are needed to get an accurate estimate of the total SPM concentration.     

一种新型海底沉积物声学原位测量系统的研制及应用

为了能够精确地测量海底表层沉积物的声学参数,自主研制了一种新型海底沉积物声学原位测量系统,与国内外传统的声学原位测量系统相比,该系统能够实时显示声波波形,调整测量参数,其工作方式除了站位式测量之外,还实现了拖行式连续测量,极大地提高了工作效率.根据前期海试情况,对海底仪器结构进行了重新设计,使之可以同时测量海底沉积物及海底海水的声学参数,同时建立了双向数字信道,解决了测量过程中系统信号的干扰问题.该系统的结构分为两部分:甲板控制单元和水下测量单元,整套系统通过主机控制程序进行控制,采用GPS定位系统测定仪器的大地坐标.为了检验系统的稳定性及准确性,分别进行了实验室水槽实验和海上试验.利用水声测量设备对测量系统进行实验室水槽标定分析,实验结果表明系统测量值相对误差仅为0.04%,测量结果具有较高的精度.海上试验在青岛胶州湾和东海海域进行,获得了试验区域海底沉积物声速和声衰减系数的测量数据,将测量数据与他人的研究结果进行对比分析,结果表明测量数据与前人研究结果一致,较为准确.该原位测量系统在站位式测量和拖行式测量中都能够快速准确地测量出沉积物声速和声衰减系数,可以作为海底底质声学测量的调查设备.     

Relationship between macrobenthos and physical habitat characters in tidal flat in eastern Seto Inland Sea, Japan

The investigations were carried out at 6 tidal flats located on the eastern part of the Seto Inland Sea, Japan. This study was focused on physical characteristics of sediments, namely as particle size of sediment and difference in elevation, and generalizes the relationship between sediments and macrobenthos. A total of 192 species were collected at 187 stations at 6 tidal flats. Physical characteristics of sediment were classified into 9 groups by cluster analysis in relation to sediment particle size and difference in elevation. Those groups had also significant difference in physical characteristics of sediments, and were characterized by some specific macrobenthos species. Distribution of macrobenthos can be explained by the classification of physical characteristics of sediment. These findings show the possibility to predict the variety of macrobenthos community using the physical characteristics of sediment.     

Influence of the biomass content in sediment on the sediment nutrient flux for a pulsed organic load

A laboratory study was carried out to investigate the influence of the biomass content in the sediment on the rate of diagenesis of particulate organic materials (POM) and the consequent sediment oxygen demand (SOD) and nutrient fluxes. Fish food pellets were loaded into the sediment to simulate a sudden POM input. Three types of sediments with different biomass contents were tested, including a raw marine sediment, the marine sediment after one month of cultivation and an artificial sediment of sand and clay without any biomass. There was little difference in organic flux from the three different sediments. However, compared to the artificial sediment, the marine sediments had much higher SOD and ammonia flux. A mathematical model also has been developed for the SOD dynamics and nutrient fluxes. Both the experimental and simulation results indicate the important role of the biomass in the sediment in POM diagenesis, SOD and nutrient fluxes.     

STABILIZING EFFECT OF BENTRIC ALGAE ON COHESIVE SEDIMENTS

I.INTRODUCTIONMOrphologicalprocessesinlotvlandriversaredond~actransportphenomenaoffineandcohesivesediments.AsthismaterialtendstobindtoxicagentsandthuSrepresentsapotentialdangerfortheaqUaticenvironmentitisofspotalinterestintennsOfwaterqualityinvestigations.BesidesthisapeOfenvironmentalprotectionfinesedimentsoftendepositinnavigationchannelsandimpedeshipping.implyingextensiveandexpensitredredging.Thesereasonsprot,e,thatthetranSPortbehal'iorOffinesedimentsshouldbeinvestigatedcarefullytogiv…     

Influence of the biomass content in sediment on the sediment nutrient flux for a pulsed organic load

A laboratory study was carried out to investigate the influence of the biomass content in the sediment on the rate of diagenesis of particulate organic materials (POM) and the consequent sediment oxygen demand (SOD) and nutrient fluxes. Fish food pellets were loaded into the sediment to simulate a sudden POM input. Three types of sediments with different biomass contents were tested, including a raw marine sediment, the marine sediment after one month of cultivation and an artificial sediment of sand and clay without any biomass. There was little difference in organic flux from the three different sediments. However, compared to the artificial sediment, the marine sediments had much higher SOD and ammonia flux. A mathematical model also has been developed for the SOD dynamics and nutrient fluxes. Both the experimental and simulation results indicate the important role of the biomass in the sediment in POM diagenesis, SOD and nutrient fluxes.     

The environmental impact of marine fish culture: Towards a sustainable future

The environmental impact of marine fish-farming depends very much on species, culture method, stocking density, feed type, hydrography of the site and husbandry practices. In general, some 85% of phosphorus, 80–88% of carbon and 52–95% of nitrogen input into a marine fish culture system as feed may be lost into the environment through feed wastage, fish excretion, faeces production and respiration. Cleaning of fouled cages may also add an organic loading to the water, albeit periodically. Problems caused by high organic and nutrient loadings conflict with other uses of the coastal zone. The use of chemicals (therapeutants, vitamins and antifoulants) and the introduction of pathogens and new genetic strains have also raised environmental concerns.

Despite the high pollution loadings, results from various studies show that some 23% of C, 21% of N and 53% of P of feed input into the culture system is being accumulated in the bottom sediments and the significant impact is normally confined to within 1 km of the farm. The major impact is on the sea bottom, where high sediment oxygen demand, anoxic sediments, production of toxic gases and a decrease in benthic diversity may result. Decreases in dissolved oxygen and increases in nutrient levels in the water are also evident but are normally confined to the vicinity of the farm. Tributyltin (TBT) contamination and the development of antibiotic-resistant bacteria have been reported near fish farms. The stimulating effects of vitamins/fish wastes on growth of red tide species have been demonstrated in a number of laboratory studies. Nevertheless, there is no evidence to support the suggestion that the present use of therapeutants, vitamins and antibiotics and the introduction of pathogens and new genetic strains would pose a significant threat to the environment.

Marine fish culture can be a sustainable development, provided pollution loadings generated by fish farms are kept well below the carrying capacity of the water body. Effects can be significantly reduced by careful site selection, control of stock density, improved feed formulation and integrated culture (with macroalgae, filter-feeders and deposit-feeders). An example of the application of computer modelling in mariculture management is demonstrated. Environmental impact assessment and monitoring should also be carried out to ensure culture activities are environmentally sustainable.     

Rapid age assessment in the Namib Sand Sea using a portable luminescence reader

A rapid assessment of burial age for sedimentary materials is useful to aid in-situ interpretation of sites and sequences during fieldwork. This can assist with targeted field sampling strategies for full dating back in the laboratory, for example when the study is concerned with reconstructing landscape dynamics during a specific time period. Field-based luminescence measurements are possible using a portable luminescence reader; the challenge is translating relative portable luminescence reader signal intensities of samples into an estimate of age. This study uses a portable luminescence reader for the first time in the analysis of African dunefield sediments. Samples from the Namib Sand Sea (NSS) with established luminescence ages are used to assess what in-situ information about relative sample age can be gleamed at and between sites using the portable luminescence reader, and to establish whether first-order estimates of sample age can be obtained. Two sites in the NSS, which are of modern, very late Holocene and last interglacial age were selected for this assessment and a simple calibration between portable luminescence reader signals and sample age is made. Results show that portable luminescence reader signals differ by over two orders of magnitude between late Holocene and last interglacial age samples and that useful relative-age information can be established using bulk material in the field. Predicted ages from portable luminescence reader signals using a linear regression appear to be indicative and useful. Further development of this calibration using a wider range of sample ages would confirm its applicability in the NSS, and a similar approach is applicable to other sand sea environments.     

Electric imaging and laboratory resistivity testing for geotechnical investigation of Pusan clay deposits

Large-scale reclamation works for new land development in the Nakdong River plain have been extensively carried out on soft clays. Several geotechnical characteristics of the clays could not be well evaluated, partly due to easy disturbance during drilling and sampling. Consequently, geophysical methods, seen as nondestructive testing tools, have been applied in geotechnical investigation of Pusan clays for the first time. In this study, the 2D electric imaging technique was employed to map the thick soft clay deposits in four reclamation sites. The Pusan clay deposit was very well mapped. Electric resistivity of Pusan clays was measured on over 50 core samples in the laboratory, and then correlated with other geotechnical parameters such as salinity, organic content, water content, plasticity, unit weight and sampling depth. Additionally, electric resistivity of about 20 natural clays collected worldwide was measured and compared to that of the Pusan clays as an initial effort in creating a database of clay electric resistivity to help further application of electric imaging in geotechnical investigation of clayey soils.     

Quantifying the response of optical backscatter devices and transmissometers to variations in suspended particulate matter

Optical instruments have been used effectively in studies of sediment dynamics for several decades. Without accurate instrument calibrations, calculated concentrations of suspended particulate matter (SPM) may be unreliable, with implications for interpretations of sedimentary processes and sediment fluxes. This review aims to quantify the effect of variations in SPM characteristics on the response of optical instruments (optical backscatter sensors OBS and transmissometers) and to note the implications for users of these instruments. A number of factors have a significant impact on instrument response, for example; a change in grain size from medium sands to fine silts may lead to a×100 increase in instrument response; flocculation of fine particles may decrease instrument response by×2; and the presence of plankton in suspension may lead to poor instrument calibrations of SPM concentration. Calibrations carried out in environments either with multi-modal bottom sediments, where flocculation of fine-grained sediments is likely, or where the hydrodynamics or grain type are highly variable must also include a determination of the changing nature of the suspended load in space and time. A more complete understanding of instrument response to SPM and of calibration requirements may enable optical devices to be used to a greater potential as long-term measures of SPM concentration, and also enable improvements in calculations of net sediment fluxes.     

Quaternary deformation mapping with ground penetrating radar

Ground penetrating radar (GPR) was used in a programme of geological and hydrogeological investigations into the Quaternary of west Cumbria, UK. The investigations were part of an extensive programme to determine the suitability of the area for a deep radioactive waste repository. The hydrogeological characteristics of the drift deposits are important since they affect both recharge and discharge. The glacially derived Quaternary sediments include a variety of deformation structures related to their mode of deposition and subsequent modification by glacial and periglacial processes. These deformation structures range from variable scale thrusts (centimeter to tens of meter displacement due to proglacial thrusting) to small to medium scale faults, folds and collapse structures which are early or syn-sedimentary adjustments. From the GPR data a number of dipping reflectors, having dip angles in the range of 8–23°, were interpreted as thrust planes and related faults and folds have been clearly observed. Inwardly dipping reflectors, having a maximum dip angle of 36°, creating a characteristic `V' shaped anomaly, were also observed and interpreted to be linear collapse structures where glacitectonically emplaced slices of ice melted out causing sediments to slump. Lateral continuations, up to 90 m, of GPR-interpreted dislocations were mapped between survey lines, suggesting that such features could be laterally continuous on the scale of hundreds of metres.     

A Diffusive Sampler for Passive Monitoring of Underground Storage Tanks

Passive measurements of volatile organic compounds (VOCs) provide a method for early detection and long-term monitoring of potential leaks from underground storage tanks (USTs) and associated fuel service lines. A diffusive sampler was constructed of a sorbent tube that fits inside a specially designed sampling chamber. VOCs in the soil enter the chamber by molecular diffusion and are collected by the sorbent. The sorbent is easily retrieved for laboratory analyses by thermally desorbing into a gas chromatograph/mass spectrometer (GC/MS), or qualitative concentrations can be determined directly in the field with specific-indicator detectors.
The diffusive samplers were evaluated in an exposure chamber under controlled conditions. Laboratory measurements of the sorbed mass of organic vapor were found to be in close agreement with theoretical values and indicate the passive sampling approach is viable for detecting relatively low concentrations of organic vapors in the vadose zone over a one-day sampling period, as well as providing relatively long-term monitoring periods up to 58 days. A field test found the sampling approach successful in identifying an area where the vadose zone was contaminated by leaking petroleum USTs.     

The use of statistical methods to separate natural background and anthropogenic concentrations of trace elements in radio-chronologically selected surface sediments of the Venice Lagoon

A new method has been developed that predicts the natural background concentrations of microelements of interest in sediments using the concentrations of various components present in the sample. This is done by developing multiple linear regressions using a dataset which has been selected, using radiochronological dating and statistical methods, to reflect the concentration distributions of natural levels of a large number of sediment constituents. This method is demonstrated in Venice Lagoon, using data generated in a lagoon-wide sampling effort. A quantitative assessment is carried out of the variability of natural background levels at the lagoon scale for the main inorganic microelements, and distribution maps of the background and anthropogenic concentrations of a selected metal (Ni) in sediments at the lagoon scale are presented. With sufficient data, this method can be applied in other areas, allowing for a site-specific separation of natural background and anthropogenic levels of microconstituents in sediments, providing insights into regional geochemistry and aiding in the risk-based management of coastal sediments.     

A Discrete Point Sampler for Ground Water Monitoring Wells

A discrete point sampler has been developed that overcomes disadvantages inherent in several current small-volume samplers. It is designed to obtain ground water samples after a well has been purged with a pump. It consists of a sample chamber, two ports, and a stopcock for withdrawing sample aliquots. After lowering the sampler into a well, sampling is initiated by pulling on a line that sequentially removes the plugs in the lower and the upper level ports. The sample chamber fills from the bottom port and vents air from the top port. The device is suitable for sampling for volatile organic compounds in ground waters that are not subject to spontaneous bubble degassing. The upper port is sufficiently far above the lower port that none of the water that is sampled is exposed to the vented air. The sample chamber fills in such a way that the water that is taken from the chamber for analysis is not exposed to the headspace in the chamber.     

A field test of imaging properties of rotational invariants of the magnetotelluric impedance tensor

A part of the Békés Basin (an extensional sub‐basin of the Pannonian Basin, where the basement under thick Pannonian sediments is well known from deep boreholes and from seismic measurements, and where many magnetotelluric (MT) soundings have been carried out for frequencies ranging from 1 to 10^?3 Hz) was selected as a test area to assess the imaging performances of various apparent‐resistivity definitions computed with rotational invariants of either the real part of the complex impedance tensor, or its imaginary part, or both. A comparison (based on earlier 3D numerical studies) has been made between the magnetotelluric images obtained in this way and the depths to the high‐resistivity basement, as known from boreholes and seismic investigations. The correlation coefficient between the series of basement depth values at 39 MT sites and the apparent‐resistivity values was found to be stronger and high correlation appeared at a shorter period when it was computed with apparent resistivities based on the real tensor rather than with apparent resistivities based on the imaginary tensor. In the light of our studies, ρ_{Re Z} and the impedance phase seem to be more informative than any other combination of magnetotelluric interpretation parameters.     

附着藻类对太湖沉积物磷释放的影响

附着藻类是清水态浅水湖泊的重要组成部分,为了解附着藻类对湖泊沉积物磷释放的影响,在室内柱状装置中,将尼龙网所培养的附着藻类加盖到太湖沉积物上,即处理组,并设置无附着藻类加盖的对照组,进行为期13d的实验.结果表明:加附着藻类的处理组中的无机磷释放速率显著低于无附着藻类的对照组.与对照组相比,实验期间加附着藻类的处理组释放到水体中的磷,平均减少1.16mg.其中附着藻类吸收了0.81mg磷(70%),而附着藻类通过光合作用改变沉积物表面的氧环境抑制了0.35mg磷的释放(30%).研究表明,底栖附着藻类可以通过吸收磷和抑制沉积物磷释放降低水中营养盐含量.     

Monitoring polycyclic aromatic hydrocarbons in the Northeast Aegean Sea using Posidonia oceanica seagrass and synthetic passive samplers

The concentrations of 22 polyaromatic hydrocarbons (PAH) in Posidonia oceanica seagrass, sediments, and seawater from the Alexandroupolis Gulf in the Aegean Sea, were investigated from 2007 to 2011. Temporal trends of total PAH contents in P. oceanica and sediments were similar. PAH levels in seawater, sediments, and seagrasses generally decreased with increasing distance from Alexandroupolis Port. Leaves and sheaths of P. oceanica had higher PAH levels than roots and rhizomes. P. oceanica accumulates PAHs and has good potential as a bioindicator of spatiotemporal pollution trends. PAH concentrations were also examined using in situ passive seawater sampling and were compared to results of passive sampling in the laboratory using local sediments and seawater. Levels of high molecular weight PAHs assessed using passive samplers confirmed the decreasing gradient of pollution away from Alexandroupolis Port. Passive sampling also proved useful for investigating sources of PAHs in P. oceanica meadows.