The Stress Concentration of Multiplanar Tubular Joints of Offshore Structure

- The formulation for the stress concentration matrix of multiplanar tubular joint with braces subjected to combined load is established in this paper. The formulations for SCF values of multiplanar tubular joints are compared with those by Wordsworth and Efthymiou. The stiffening effect and load-interaction effect are discussed. A spatial offshore jacket with braces subjected to combined load is computed as a numerical example. The maximum stress of each multiplanar tubular joint and its location are found through SCF matrix. Finally, the difference between the maximum stresses of multiplanar tubular joints and their corresponding uniplanar tubular joints are discussed.     

TY型管节点局部柔度的参数分析及试验研究

由于海洋平台管节点的局部柔度对平台结构的静动力性能有重要影响，如何确定各类管节点的局部柔度成为一个重要的研究课题。本文用半解析方法计算了海洋平台中一类常见的管节点──ＴＹ型管节点的局部柔度，并用回归方法得出了计算ＴＹ型管节点局部柔度矩阵中各元素的参数公式。本文还介绍了对一组ＴＹ型管节点ＰＶＣ塑料模型进行的局部柔度试验。参数公式计算结果与模型试验结果的比较表明，本文得出的参数公式是基本可靠的，建议可在海洋平台总体结构分析中使用。     

Parametric Analysis and Experimental Study on Local Flexibility of TY-Type Tubular Joints

Loal flexibility of tubular joints has important effect on the static and dynamic behaviour of offshore platforms, therefore, the determination of it becomes an important research subject in the field of offshore engineering. In this paper, the local flexibility of TY-type tubular joints, which are widely used in offshore platforms, is calculated by using semi- analytical method. Based on the calculated results, parametric formulae for evaluating element in the local joint flexibility matrix of TY- type tubular joints are derived by regression. A test on PVC models of TY-type tubular joints to measure the local joint flexibility is also reported. A comparison of the results calculated from the parametric formulae presented in this paper with those measured from the model test shows that the parametric formulae are reliable. It is recommended that these formulae be used in the global structural analysis of offshore platforms.     

Regression Formulations for the Stress at Hot Spot of Multiplanar Tubular DT Joints

- Stress concentration analysis of multiplanar tubular DT joints plays an important role in the fatigue design of offshore platforms. A semi-analytic method for stress analysis under the condition of any loads is briefly introduced in the paper. Nineteen multiplanar tubular DT joints with one of two braces of the same dimension subjected to axial loads and out- of- plane bending moments are computed for parametric stress analysis by using the present method. The influence of geometrical parameters on the stresses of multiplanar tubular DT joints is discussed and compared with corresponding uniplanar T joints. The regression formulae for the stress at hot spot of multiplanar DT joints are found by modification of SCF of corresponding uniplanar T joints. The parametric formulae for the maximum stress by superposition. Finally, the influences of stiffening effect and load-interaction effect on the maximum stress of DT joints are discussed.     

Structural Analysis of Platforms with the Effect of Joint Flexibility

- A modified space beam element is presented in this paper to consider the local joint flexibility of T, Y tubular joints subjected to axial forces and in- plane bending moments for analysis of platforms. Two numerical examples are shown to verify the efficiency and validity of the method presented here.     

A Ring Model for Limit Analysis of Spatial XX Tubular Joints

-A ring model is developed to investigate the ultimate strength of tubular X and XX joints in the case that the brace is compressed. In the present analysis, the tubular joint is made of elasto-perfectly-plastic material, and the arch element of the chord section intersecting with the brace is assumed to be rigid. It is found that when 6 plastic hinges for X joint and 8 plastic hinges Tor XX joint appear in the ring, the limit state is reached, and by means of the equivalent ring width Be formula proposed in a previous paper by the authors, the ultimate strength of tubular X and XX joints subjected to compression can be obtained.     

An Improved Formulation for the Ultimate Static Strength of Tubular Joints subjected to Combined Loads

"The effect of interaction of loads on the ultimate static strength of tubular joints of offshore fixed platforms, is a practical problem. But there is still absence of rigorous theory to explain available experimental data and empirical criteria for the static strength of tubular joints. The idea of yield at hot spot of tubular joints is introduced in this paper. The interaction equations of plastic capacity for the tubular joints under combined loads (two and three different kinds) are derived. Thereafter the Yura's test data and empirical criteria of ultimate static strength for the tubular joints can be explained. The idea of classification of category of loads in accordance with experimental data and the present theory is suggested. Finally, the improved ultimate capacity equations for tubular joints are recommended. The physical significance of the coefficient of plastic reservation Qp is discussed.     

非常规管节点疲劳寿命分析与计算

对非常规管节点的疲劳寿命进行了分析研究，用SESAM计算疲劳载荷，应用精细有限元分析计算热点应力，用规范的S—N曲线计算管节点的疲劳寿命。通过实例计算表明，这些处理对非常规管节点疲劳寿命分析与计算是很有效的。     

KK型管节点应力集中系数几何敏感性分析

KK型管节点是自升式平台桁架式桩腿中的一种管节点，其应力集中系数是影响桩腿疲劳寿命的重要参数。应力集中系数与管节点的几何形式密切相关，为分析KK型管节点应力集中系数对几何参数的敏感性，利用ANSYS软件对某KK型管节点进行几何参数化建模，利用有限元数值模拟方法对各工况下的热点应力进行分析，并分别计算各相应工况下的名义应力，然后将热点应力与名义应力相比得到不同几何参数下的热点应力集中系数。对计算结果进行整理分析，得到了KK型管节点应力集中系数对无量纲几何参数的敏感性规律。结果表明，应力集中系数与撑杆受力状态、管节点结构形式有关，在满足结构布置、建造工艺和其他安全性指标的前提下，分析结果能够为KK型管节点的结构设计和疲劳分析提供技术支撑。     

Truss Spar平台桁架管节点疲劳分析

Truss Spar平台在风、浪、流的作用下,结构受力十分复杂,准确分析其疲劳强度相当困难。通过建立Truss Spar平台三维有限元模型,利用HydroD软件进行载荷预报、波浪搜索,得到产生最大应力幅响应的最不利浪向和相位角。运用Sestra软件进行整体有限元分析,得到的结果作为桁架管节点细化模型的边界条件,再用Nastran软件进行局部分析求得节点的热点应力,修正壁厚影响。最后根据DNV规范的S-N曲线计算了管节点的疲劳寿命。     

安全叠接管节点在低周循环载荷下的破坏模式研究

采用实验和数值模拟方法研究了一种新型海洋平台管节点在地震载荷下的响应和破坏情况。采用拟静态循环加载模拟地震载荷 ,对真实尺寸的试件进行实验 ,研究局部屈曲和裂纹等对管接点抗震性能的影响。能量分析表明 ,发生在斜支管中的局部屈曲消耗了大部分输入能量。与现在使用的N型管节点相比 ,该新型管节点有较好的抗震性能。采用有限元数值模拟方法分析比较了不同尺寸配置下 ,该型管节点的响应曲线     

Fatigue Test of Homemade Z Direction Steel Welded T Tubular Joints

This paper introduces the process and result of fatigue test of steel (Z direction steel) welded T tubular joints used in offshore engineering. Detailed measurement of stress concentration factor, stress distribution, fatigue life and crack development has been performed. Through analysis, an empirical formula of stress concentration factor for T tubular joints, fatigue S-N curve and crack propagation rule are obtained.     

Elasto-Plastic Analysis of Tubular Joints of Offshore Platforms by Finite Element Method

The plastic node method is reformulated by the variational principle and is applied to elasto-plastic finite element analysis of tubular joints, eventually including the effect of internal and external gussets, stiffener rings, etc., if necessary. Four different joints are studied here in detail for the elasto-plastic behavior, the strain at the hot spot, the strain concentration factor around the intersection line, and the propagation of the plastic region with loading up to collapse in order to determine the ultimate strength, safety factor, and development of the plastic field. The present results are in good agreement with the experimental results.     

极端波浪作用下海上施工栈桥承载性能评估

海上施工栈桥作为一种可以快速装配的施工辅助设施,在跨海大桥建设中得到广泛应用。为研究海上施工栈桥在极端波浪作用下的结构性能,基于波浪增量分析(IWA)理论,提出海上施工栈桥承载性能评估方法。以某在役海上施工栈桥为例,考虑杆件弹塑性和节点局部柔性建立结构非线性分析模型,评估了海上施工栈桥在不同方向极端波浪荷载作用下的结构承载性能及倒塌失效模式。研究表明,随着极端波高逐渐增大,栈桥依次出现首次屈服、塑性铰和倒塌起始三种非线性行为点,结构将依次经历正常使用、可以使用、临近倒塌和倒塌破坏四个承载性能状态;波浪入射方向对于海上施工栈桥的承载性能和倒塌失效模式影响较大;海上施工栈桥的主要薄弱部位位于钢管桩桩底及其与支撑框架下横撑相交的节点处,应在设计中重点关注。     

Nonlinear joint flexibility element for the modeling of jacket-type offshore platforms

A new nonlinear two-dimensional tubular joint element is developed in this study on the basis of flexibility equations and the interaction between the axial force and the in-plane bending moment in the joint. Empirical equations are used to define the joint yielding in the axial direction and the in-plane rotation. An elastic-perfectly plastic yield function is adopted to include the combined effects of axial loads and bending moments on the yielding of the joint. The element formulation is straightforward, and it can readily be implemented in nonlinear finite element programs. Verification studies are carried out for the element to prove its suitability for the modeling of tubular joints of offshore jacket structures. It is concluded that the nonlinear joint model that has been developed produces accurate results, verified against experimental data as well as against sophisticated multi-axial finite element joint models.     

Prediction of Static Strength of Tubular T and X Joints Subjected to Axial Compression

-The formulation of ring analogy method for the prediction of static strength (ductile collapse) of tubular T, X joints under axial compression based on the limit analysis of the ring with some assumptions is presented in this papaer. The regression formula for the effective length of the chord based on test results is established by means of the least square method. The results computed by the present semi-analytic formula are compared with previous results and test data. They are quite close to each other. The accuracy of the present formula depends on the reasonable selection of the effective length of the chord, which requires numerous test data.     

广州港新沙港区板桩码头结构设计方案比选分析

介绍了广州港新沙港区板桩码头主要内力计算方法及常用软件,结合设计过程、工程地质情况、现场实际施工情况,着重从受力合理性、施工便利性、节省造价方面,对提出的钢板桩方案、钢管板桩方案进行比较分析,确定了钢管板桩结构更合理,并对优势进行总结。研究表明相对于钢板桩结构,钢管板桩结构在抗弯、抗变形、拉杆拉力和锚碇墙稳定性、对复杂地基(软弱土层较厚、岩层标高较高的地基)适应性、兼顾桩基基础、施工速度等方面更具备优势,且钢管板桩结构可更好的适应码头的大型化和深水化发展,在类似工程设计中可优先采用钢管板桩结构。     

A study on the Local Joint Flexibility (LJF) of two-planar tubular DK-joints in jacket structures under in-plane bending loads

In the present paper, results of a parametric study conducted on the Local Joint Flexibility (LJF) of two-planar tubular DK-joints under In-Plane Bending (IPB) loads are presented. DK-joints are among the most common joint types in jacket substructure of Offshore Wind Turbines (OWTs). A total of 324 finite element (FE) analyses were carried out on 81 FE models under four types of IPB loading in order to investigate the effect of the DK-joint’s geometrical parameters on the LJF factor (f_LJF). Based on the results of parametric study, the factors leading to the LJF reduction were introduced. Generated FE models were verified using the existing experimental data, FE results, and parametric equations. The effect of the weld profile was also considered. The f_LJF in two-planar DK- and uniplanar K-joints were compared. Results indicated that the effect of multi-planarity on the LJF is quite significant and consequently the use of the equations already available for uniplanar K-joints to calculate the f_LJF in two-planar DK-joints may lead to highly under-/over-predicting results. To handle this issue, the FE results were used to derive a set of parametric equations for the prediction of the f_LJF in IPB-loaded two-planar DK-joints. The proposed equations were checked against the acceptance criteria recommended by the UK DoE and can be reliably used for the analysis and design of tubular joints in OWTs.     

Fatigue Behaviour of Tubular Joints Made of China-Made Platform Steel

In China, a nationwide research program on fatigue behaviour of tubular joints made of China-made platform steel was carried out from 1983 to 1990, which was set by the Tubular Joint Research Committee for Offshore Structures (TJCOS) of China. This paper gives an outline of the basic properties of the China-made platform steel and fatigue test of tubular joints, including test specimens, test particulars and test results. A p-S-N curve based on the test results was established which reveals that the fatigue strength of tubular joints is fairly good. The thickness effect and effect of corrosion on fatigue strength in sea water are briefly discussed.     

Optimum design of ice-resistant offshore jacket platforms in the Bohai Gulf in consideration of fatigue life of tubular joints

Economy and ice-resistance are two factors that must be considered in the design of offshore oil platforms in the Bohai Gulf. This paper focuses on the optimal design of ice-resistant offshore jacket platforms in the Bohai Gulf in consideration of fatigue life of tubular joints, with the minimum initial weight and satisfying dynamic properties. An efficient fatigue analysis procedure based on spectral analysis is proposed, in which a hybrid finite element model is adopted to simulate the jacket platform and the tubular joints, and the pseudo-excitation method is used to calculate the power spectral density of the hot spot stress. Finally, a practical jacket platform with an ice-breaking cone in the Bohai Gulf is optimized, and the results demonstrate that the fatigue life of tubular joints could be improved and the weight of jackets decreased simultaneously.