塔克拉玛干沙漠腹地沙尘暴过境时近地层风速、温度和湿度廓线特征

利用塔中80m梯度观测塔探测系统采集的资料,详细的分析了2006年4月10日沙尘暴过境时,塔克拉玛干沙漠腹地近地层风速、温度和湿度廓线的演变特征。结果表明:风速廓线满足风速值随高度增高而增大,风速梯度随高度增高而减小的对数律关系;沙尘暴由爆发前到过境时,温度廓线的温度值由随高度增高而增大转变为温度值随高度增高而减小,同时在贴地层2m处存在一微弱拐点;沙尘暴过境时,近地层大气出现微弱逆湿现象,并在不同高度上存在多处拐点,比湿增减在时间上与风速的增减呈负相关性,且整个沙尘暴天气是一个降温增湿的过程。     

A Flume Experiment on the Adjustment of the Mean and Turbulent Statistics to a Transition from Short to Tall Sparse Canopies

Water-flume experiments are conducted to study the structure of turbulent flow within and above a sparse model canopy consisting of two rigid canopies of different heights. This difference in height specifies a two-dimensional step change from a rough to a rougher surface, as opposed to a smooth-to-rough transition. Despite the fact that the flow is in transition from a rough to a rougher surface, the thickness of the internal boundary layer scales as x ^4/5, consistent with smooth-to-rough boundary layer adjustment studies, where x is the downstream distance from the step change. However, the analogy with smooth-to-rough transitions no longer holds when the flow inside the canopy and near the canopy top is considered. Results show that the step change in surface roughness significantly increases turbulence intensities and shear stress. In particular, there is an adjustment of the mean horizontal velocity and shear stress as the flow passes over the rougher canopy, so that their vertical profiles adjust to give maximum values at the top of this canopy. We also observe that the magnitude and shape of the inflection in the mean horizontal velocity profile is significantly affected by the transition. The horizontal and vertical turbulence spectra compare well with Kolmogorov’s theory, although a small deviation at high frequencies is observed in the horizontal spectrum within the canopy. Here, for relatively low leaf area index, shear is found to be a more effective mechanism for momentum transfer through the canopy structure than vortex shedding.     

Regional roughness of the landes forest and surface shear stress under neutral conditions

Mean wind velocity profiles were measured by means of radio-windsondes over the Landes region in southwestern France, which consists primarily of pine forests with scattered villages and clearings with various crops. Analysis of neutral profiles indicated the existence of a logarithmic layer between approximately z – d ₀ = 67(±18)z ₀ and 128(+-32)z ₀ (z is the height above the ground, z ₀ the surface roughness and d ₀ the displacement height). The upper limit can also be given as z – d ₀ = 0.33 (±0.18)h, where h is the height of the bottom of the inversion. The profiles showed that the surface roughness of this terrain is around 1.2 m and the displacement height 6.0 m. Shear stresses derived from the profiles were in good agreement with those obtained just above the forest canopy at a nearby location with the eddy correlation method by a team from the Institute of Hydrology (Wallingford, England).     

塔中春季阴天近地层风速、温度和湿度廓线特征分析

利用塔中最新安装的80 m梯度观测塔探测系统采集的资料,详细分析了2006年4月2日1次阴天天气时塔克拉玛干沙漠腹地近地层风速、温度和湿度廓线演变特征,并与典型晴天廓线做了对比,得到以下结果:(1)阴天,夜间风速廓线风速值随高度增高而增大,但不是以对数增长,而是以比对数关系更快的速度增长;白天,风速很小,近地层10 m上下廓线分布规律各异;(2)温度廓线有夜间辐射型、早上过渡型、白天日射型及傍晚过渡型4种类型,与晴天类似;(3)比湿廓线存在一个极小值,其出现高度以上比湿随高度增加而增加,廓线呈逆湿特征,极小值出现高度以下比湿随高度减小而增加。     

Local similarity relationships in a horizontally inhomogeneous boundary layer

Local similarity theory, an analogy to the Monin-Obukhov similarity theory, is successfully applied to airborne observations in a coastal area of South Australia. The boundary layer over this highly non-uniform surface is characterized by extensive variations in its thermal stratification and turbulence characteristics. However, the behaviour of some statistical parameters of second- and higher moments seems to be determined mainly by local forcing, while horizontal advection plays a less important role. For these parameters, local scaling is effective. It is shown that the dimensionless variances of vertical velocity and potential temperature are functions of z/ only, where is the local Monin-Obukhov length and z is the height above ground. The dimensionless variance of horizontal velocity components is found to depend on h/, where h is the height of the oundary layer. Similarity relationships for some triple correlations are also discussed. The empirically determined local similarity relationships are found to agree with those obtained from surface-layer similarity. Finally, to illustrate the complexity of the local forcing, distributions of vertical energy and momentum fluxes, from which the local scaling parameters are derived, are shown.     

Deduction of the Sensible Heat Flux from SODAR Data

A new method for deduction of the sensible heat flux is validated with three sets of published SODAR （sound detection and ranging） data. Although the related expressions have previously been confirmed by the author with surface layer data, they have not yet been validated with observations from the boundary layer before this work. In the study, selected SODAR data are used to test the method for the convective boundary layer. The sensible heat flux （SHF） retrieved from SODAR data is found to decrease linearly with height in the mixed layer. The surface sensible heat fluxes derived from the deduced sensible heat flux profiles under convective conditions agree well with those measured by the eddy correlation method. The characteristics of SHF profiles deduced from SODAR data in different places reflect the background meteorology and terrain. The upper part of the SHF profile （SHFP） for a complicated terrain is found to have a different slope from the lower part. It is suggested that the former reflects the advective characteristic of turbulence in upwind topography. A similarity relationship for the estimation of SHFP in a well mixed layer with surface SHF and zero-heat-flux layer height is presented.     

Nocturnal boundary layer height prediction from surface routine meteorological data

Summary A number of well known diagnostic equations for the determination of the height,h, of the nocturnal boundary layer. with minimum data requirements of at most surface wind speed, air temperature and total cloud cover, have been tested as to their effectiveness. The computed values have been compared with direct estimation ofh, from temperature or wind profiles of rawinsonde ascents available at 00Z (02h LST). The comparison between computed and observed values shows that best agreement is found when the nocturnal boundary layer height is determined through wind profiles. The ratio of the computed to the observed values reveals a strong dependence on stability, resulting in overestimation by the models for very low stability and underestimation for strong stability. The simple expressions involving the wind speed rather than other stability parameters resulted in a better overall fit to the observed values. A simple prognostic model is shown to provide the best estimates of the NBL height compared to both wind and temperature profile definition.With 5 Figures     

A parameterization of the boundary layer of a tropical cyclone

In an earlier paper by one of the authors (Smith, 1968), a momentum integral method was developed to parameterize the gross constraint imposed by the surface boundary layer of a steady, axisymmetric, tropical cyclone on the meridional circulation within the vortex itself. Specifically, the method provides an effective means of estimating the radial variation of mean upflow/downflow induced by the boundary layer, compatible with a prescribed radial variation of azimuthal velocity just above the boundary layer,V _gr. However, it relies on a judicious choice of vertical profiles of radial and azimuthal velocity components within the boundary layer. An especially suitable set of profiles is discussed herein; these are Ekman-like profiles in which turbulent mixing is characterized by a vertically constant eddy diffusivityK _M , matched to a constant stress sublayer just above the sea surface. An attractive feature of the formulation is that a suitable value forK _M as a function of radius, which is extremely difficult to extract from observational data, can be calculated when the state of the sea surface, described by a roughness lengthZ ₀, is prescribed. Although observations ofZ ₀ at high wind speeds are not yet available, the effect of radial variations in sea surface roughness can be assessed and it is shown that these affect the upflow to a significant degree.     

The structure of the stably stratified internal boundary layer in offshore flow over the sea

Observations obtained mainly from a research aircraft are presented of the mean and turbulent structure of the stably stratified internal boundary layer (IBL) over the sea formed by warm air advection from land to sea. The potential temperature and humidity fields reveal the vertical extent of the IBL, for fetches out to several hundred of kilometres, geostrophic winds of 20–25 m s^–1, and potential temperature differences between undisturbed continental air and the sea surface of 7 to 17 K. The dependence of IBL depth on these external parameters is discussed in the context of the numerical results of Garratt (1987), and some discrepancies are noted.Wind observations show the development of a low-level wind maximum (wind component normal to the coast) and rotation of the wind to smaller cross-isobar flow angles. Potential temperature () profiles within the IBL reveal quite a different structure to that found in the nocturnal boundary layer (NBL) over land. Over the sea, profiles have large positive curvature with vertical gradients increasing monotonically with height; this reflects the dominance of turbulent cooling within the layer. The behaviour is consistent with known behaviour in the NBL over land where curvature becomes negative (vertical gradients of decreasing with height) as radiative cooling becomes dominant.Turbulent properties are discussed in terms of non-dimensional quantities, normalised by the surface friction velocity, as functions of normalised height using the IBL depth. Vertical profiles of these and the normalised wavelength of the spectral maximum agree well with known results for the stable boundary layer over land (Caughey et al., 1979).     

A Comparison of Higher-Order Vertical Velocity Moments in the Convective Boundary Layer from Lidar with In Situ Measurements and Large-Eddy Simulation

We have analyzed measurements of vertical velocity w statistics with the NOAA high resolution Doppler lidar (HRDL) from about 390 m above the surface to the top of the convective boundary layer (CBL) over a relatively flat and uniform agricultural surface during the Lidars-in-Flat-Terrain (LIFT) experiment in 1996. The temporal resolution of the zenith-pointing lidar was about 1 s, and the range-gate resolution about 30 m. Vertical cross-sections of w were used to calculate second- to fourth-moment statistics of w as a function of height throughout most of the CBL. We compare the results with large-eddy simulations (LES) of the CBL and with in situ aircraft measurements. A major cause of the observed case-to-case variability in the vertical profiles of the higher moments is differences in stability. For example, for the most convective cases, the skewness from both LES and observations changes more with height than for cases with more shear, with the observations changing more with stability than the LES. We also found a decrease in skewness, particularly in the upper part of the CBL, with an increase in LES grid resolution.     

Estimation of atmospheric surface layer parameters and numerical simulation using MM5 at Mangalore, West Coast of India

Atmospheric surface layer meteorological observations obtained from 20-m-high meteorological tower at Mangalore, situated along the west coast of India are used to estimate the surface layer scaling parameters of roughness length (z _o) and drag coefficient (C _D), surface layer fluxes of sensible heat and momentum. These parameters are computed using the simple flux–profile relationships under the framework of Monin–Obukhov (M–O) similarity theory. The estimated values of z _o are higher (1.35–1.54 m) than the values reported in the literature (>0.4–0.9 m) probably due to the undulating topography surrounding the location. The magnitude of C _D is high for low wind speed (<1.5 m s^?1) and found to be in the range 0.005–0.03. The variations of sensible heat fluxes (SHF) and momentum fluxes are also discussed. Relatively high fluxes of heat and momentum are observed during typical days on 26–27 February 2004 and 10–11 April 2004 due to the daytime unstable atmospheric conditions. Stable or near neutral conditions prevail after 1700 h IST with negative SHF. A mesoscale model PSU/NCAR MM5 is run using a high-resolution (1 km) grid over the study region to examine the influence of complex topography on the surface layer parameters and the simulated fluxes are compared with estimated values. Spatial variations of the frictional velocity (u _*), C _D, surface fluxes, planetary boundary layer (PBL) height and surface winds are noticed according to the topographic variations in the simulation.     

Coherence and Scale of Vertical Velocity in the Convective Boundary Layer from a Doppler Lidar

We utilized a Doppler lidar to measure integral scale and coherence of vertical velocity w in the daytime convective boundary layer (CBL). The high resolution 2 μm wavelength Doppler lidar developed by the NOAA Environmental Technology Laboratory was used to detect the mean radial velocity of aerosol particles. It operated continuously in the zenith-pointing mode for several days in the summer 1996 during the “Lidars in Flat Terrain” experiment over level farmland in central Illinois. We calculated profiles of w integral scales in both the alongwind and vertical directions from about 390 m height to the CBL top. In the middle of the mixed layer we found, from the ratio of the w integral scale in the vertical to that in the horizontal direction, that the w eddies are squashed by a factor of about 0.65 as compared to what would be the case for isotropic turbulence. Furthermore, there is a significant decrease of the vertical integral scale with height. The integral scale profiles and vertical coherence show that vertical velocity fluctuations in the CBL have a predictable anisotropic structure. We found no significant tilt of the thermal structures with height in the middle part of the CBL.The National Center for Atmospheric Research is sponsored by the National Science Foundation.     

Variationally adjusted surface winds

This paper describes a one-level variational adjustment process for producing mass-consistent surface winds in the Barrow Strait area, N.W.T. To achieve this result, the continuity equation is employed as a physical constraint. The variational technique adjusts mean winds (vertically averaged through the planetary boundary layer); therefore, a relationship is required between surface and mean winds. Use is made of existing velocity profiles, but interpolation may be used between surface and geostrophic winds. The model was found to be strongly dependent upon specification of boundary-layer height. Channeling effects are not readily seen until topography begins to protrude through the boundary layer. The model might thus be better suited to areas where shallow inversion layers are well defined. By application of the variational adjustment, errors in continuity are reduced by six orders of magnitude. Upon comparison of the variational technique with a diagnostic, one-level, primitive equation model, median errors between computed and observed surface winds were found to be comparable.     

Velocity and Surface Shear Stress Distributions Behind a Rough-to-Smooth Surface Transition: A Simple New Model

A simple new model is proposed to predict the distribution of wind velocity and surface shear stress downwind of a rough-to-smooth surface transition. The wind velocity is estimated as a weighted average between two limiting logarithmic profiles: the first log law, which is recovered above the internal boundary-layer height, corresponds to the upwind velocity profile; the second log law is adjusted to the downwind aerodynamic roughness and local surface shear stress, and it is recovered near the surface, in the equilibrium sublayer. The proposed non-linear form of the weighting factor is equal to ln(z/z ₀₁)/ln(δ _i /z ₀₁), where z, δ _i and z ₀₁ are the elevation of the prediction location, the internal boundary-layer height at that downwind distance, and the upwind surface roughness, respectively. Unlike other simple analytical models, the new model does not rely on the assumption of a constant or linear distribution for the turbulent shear stress within the internal boundary layer. The performance of the new model is tested with wind-tunnel measurements and also with the field data of Bradley. Compared with other existing analytical models, the proposed model shows improved predictions of both surface shear stress and velocity distributions at different positions downwind of the transition.     

The computation of the friction velocity u * and the temperature scale T * from temperature and wind velocity profiles by least-square methods

A method is given to calculate the surface layer parameters: u _* (friction velocity) and T _* (temperature scale) from wind speed and temperature profiles.The problem is formulated as a minimization of a least-square function, which is constructed from the difference between the measured profiles and the well-known Kansas profile relations.The wind speed and temperature profiles are treated simultaneously in this procedure. All the available wind speed and temperature measurements are used in order to reduce the effect of measurement errors.Estimates of the goodness of fit and confidence limits on the estimated parameters are discussed.The method has been applied to data obtained during experiments in a wide variety of conditions: Project Prairie Grass, experiments over Lake Flevo and experiments at the meteorological tower at Cabauw, the last two in the Netherlands.     

On the formation of a stably stratified internal boundary-layer by advection of warm air over a cooler sea

As a warm well-mixed air mass flows off a land surface and over a cooler sea, the air is modified in a layer near the surface. Within this layer, humidity decreases while temperature increases with height and a stably stratified internal boundary layer is formed. The non-dimensional parameters governing the growth of the modified layer are derived by dimensional analysis; simple forms are found for the increase of layer height with fetch and for the shapes of humidity and temperature profiles.     

近水面层温、湿、风廓线和湍流交换规律

本文分析了官厅水库近水面层的温、湿、风廓线规律,指出水面的波浪状况对廓线规律有影响。给出了中性层结时水面粗糙度、动力摩擦速度及阻力系数与风速和浪高的关系。得出了适用于水面的层结订正函数。还分析了不稳定层结条件下的温度廓线规律,并对温、湿、风廓线的相似性问题进行了讨论。     

Estimation of abl Parameters Using the Vertical Velocity Measurements of an Acoustic Sounder

The friction velocity, the surface heat flux and the height of the Atmospheric Boundary Layer (ABL) are important parameters. In this work, vertical velocity variance ( _w ² ) and wind velocity structure parameter (C _v ² ) profiles estimated by acoustic sounder measurements are used, along with similarity relations, to estimate these parameters in the unstable Atmospheric Boundary Layer and the friction velocity in the stable one. The data were collected by two acoustic sounders with different height range and resolution under various atmospheric conditions (stability) and at two experimental sites in different terrain. The C _v ² profiles are estimated using gate difference of the vertical velocity measurements and the assumption of local isotropy. The vertical velocity data are corrected for the significant effects of noisy measurements and sampling volume averaging on the _w ² and C _v ² estimations using original techniques that are presented in this work. The results of the similarity method using acoustic sounder data are compared against estimates of the corresponding atmospheric parameters obtained from direct measurements. The comparison confirms the ability of the method to provide reasonably accurate estimates of these parameters especially in the middle of the day.     

A simple unified theory for flow in the canopy and roughness sublayer

The mean flow profile within and above a tall canopy is well known to violate the standard boundary-layer flux–gradient relationships. Here we present a theory for the flow profile that is comprised of a canopy model coupled to a modified surface-layer model. The coupling between the two components and the modifications to the surface-layer profiles are formulated through the mixing layer analogy for the flow at a canopy top. This analogy provides an additional length scale—the vorticity thickness—upon which the flow just above the canopy, within the so-called roughness sublayer, depends. A natural form for the vertical profiles within the roughness sublayer follows that overcomes problems with many earlier forms in the literature. Predictions of the mean flow profiles are shown to match observations over a range of canopy types and stabilities. The unified theory predicts that key parameters, such as the displacement height and roughness length, have a significant dependence on the boundary-layer stability. Assuming one of these parameters a priori leads to the incorrect variation with stability of the others and incorrect predictions of the mean wind speed profile. The roughness sublayer has a greater impact on the mean wind speed in stable than unstable conditions. The presence of a roughness sublayer also allows the surface to exert a greater drag on the boundary layer for an equivalent value of the near-surface wind speed than would otherwise occur. This characteristic would alter predictions of the evolution of the boundary layer and surface states if included within numerical weather prediction models.     

The Effects of Inner- and Outer-Layer Turbulence in a Convective Boundary Layer on the Near-Neutral Inertial Sublayer Over an Urban-Like Surface

A large-eddy simulation of the atmospheric boundary layer, large enough to contain both an urban surface layer and a convective mixed layer, was performed to investigate inner-layer and outer-layer scale motions. The objective was to determine the applicability of Monin–Obukhov similarity theory to inner-layer motions, to investigate the influence of outer-layer motions on surface-layer structure, as well as to assess the interaction of the two scales of motion. The urban surface roughness consisted of square-patterned cubic buildings of dimension H (40 m). A spatial filter was used to decompose the two scales in the inertial sublayer. The horizontal square filter of size 10H was effective in separating the inner-layer (surface-layer height ≈ 2 H) and outer-layer scales (boundary-layer height δ ≈ 30H), where the Reynolds stress contribution of the inner layer dominates in the logarithmic layer (depth 2H). Similarity coefficients for velocity fluctuations were successfully determined for inner-layer motions in the surface layer, proving the robustness of Monin–Obukhov similarity for surface-layer turbulence. The inner-layer structures exhibit streaky structures that have similar streamwise length but narrower spanwise width relative to the streamwise velocity fluctuation field, consistent with observations from an outdoor scale model. The outer-layer motions to some extent influence the location of ejections and sweeps through updraft and downdraft motions, respectively, thus, disturbing the homogeneity and similarity of inner-layer motions. Although the horizontal averages of the variances and covariance of motions reveal that the Reynolds stresses are dominated by inner-layer structures, the localized influence of the interaction of outer-layer horizontal and inner-layer vertical motions on the Reynolds stress is not insignificant.