海底管线柔性导流板的变形方程研究

海底输油管线是海洋油气田开发的生命线工程,在复杂的海洋环境中易发生破坏.为使管线实现自埋防护,提出用柔性材料代替刚性导流板安装在管线顶部,不仅可以增加阻水面积,加大冲刷深度和范围,而且可以减缓刚性导流板对管线上部水流的扰动强度和尾流涡旋的扰动强度,减小管线的振动.利用力学关系由变形方程推导出海底管线与海底间距离为零以及不为零情况下柔性导流板变形的二次曲面方程和自由端最大挠度.在单向流条件下将不同材料不同长度的柔性导流板安装在管线中轴上方开展试验研究,测量柔性导流板在水流作用下的变形曲面.对比分析利用公式计算柔性导流板的自由端最大挠度和曲面变形数据与试验结果,发现两者吻合较好.     

海流作用下阻流器对海底管线自埋影响研究

研究了海流作用下不同阻流器对海底管线自埋的影响。通过参数分析的方法对阻流器高度、安装间隙、来流速度和安装角度等因素进行了研究,同时在Fluent软件中通过自定义函数来定义管道的下沉速度,模拟了管道自埋的动态过程。研究发现床面最大剪切力随着阻流器高度增加而增大,对比不同阻流器高度的计算结果,在D/8~D/4范围内效果最好。流速必须达到1.2 m/s以上才能满足自埋的要求。在0°安装位置时,管道获得向下的升力最大。随着间隙的不断扩大,床面最大剪切力在数值上整体呈现减小的趋势。     

Spoiler自埋技术特点及其在杭州湾海底管道运行情况分析

海底管道阻流板(Spoiler)自沉埋技术是一种新型管道自埋技术,为深入了解其作用机制及其效果,本文通过分析安装有阻流板的杭州湾海底管道历年检测资料,结合管道附近海域海床、潮流动力特性,深入探讨了阻流板装置在实际工程中的运行效果,分析了其作用机制及其适用条件。研究发现安装阻流板装置的杭州湾海底管道在往复潮流作用下逐渐埋入海床,其埋入段长度由2005年的50%增加到2013年的80%以上,而且平均埋入深度超过2.6 m,自埋效果较好;而在管道路由与海流平行段或管道敷设于抗冲刷强海床上时,阻流板作用不能有效发挥,管道仍然呈现裸露状态。     

粉沙海床管道在联锁排防护下的冲刷试验研究

采用当地海床的天然粉沙进行试验床面的设计,对海底管道在实际海床受到的极限波浪和最大水流作用进行试验,在管道上方铺设混凝土联锁排,对联锁排块体稳定性和其对管道防护的有效性进行研究。通过物理模型试验,研究了在极限波浪和最大水流作用下,管道在粉沙床面最大冲刷深度。通过不同水深中波流条件下研究了混凝土联锁排防护效果及其周围床面的冲刷变化,观测了联锁排的稳定性。试验结果表明:按半经验半理论简化公式得出的联锁排厚度能满足稳定性的要求,比水利部规范计算的联锁排厚度偏大的公式更加适合应用,试验期间混凝土联锁排的排面稳定,能有效保护管道,在该防护下管道没有冲刷,只在联锁排上下游与床面接触的来流段和尾端有冲刷,但该冲刷深度不影响联锁排整体的稳定性。     

海流作用下海底管道局部冲刷数值分析

在任意拉格朗日-欧拉参考坐标系下,采用基于雷诺平均的Navier-Stokes方程组(RANS)、流线迎风有限元方法、泥沙输运模型以及底床变形方程,对海流引起的海底管道局部冲刷进行了数值模拟。着重讨论了均匀来流流速和海底管道直径对局部冲刷发展过程及平衡冲刷深度的影响作用。数值结果表明,在冲刷的初始阶段,冲刷深度随时间迅速增加,之后缓慢逼近极限平衡深度;在管径一定的情况下,管道附近的局部平衡冲刷深度与流速大致呈线性关系;当流速超过某一临界区域后,最大平衡冲刷深度出现的位置并不在管道正下方,而是随流速的增加向管道下游方向移动;另外,管道直径也会对平衡冲刷深度产生比较明显的影响,在相同流速下,平衡冲刷深度大致随管径呈线性增大。在本文的计算范围内,海底管道的相对局部平衡冲刷深度基本随雷诺数线性增加,但流速对冲刷深度的影响作用要比管径的影响作用更为明显。     

套筒对波流作用下桩基局部冲刷防护试验研究

为减轻桩基局部冲刷对近海结构物稳定性造成的影响,采用套筒作为冲刷防护措施。在波流水槽中开展局部冲刷物理模型试验,改变波流条件、套筒相对高度和直径,记录套筒内外冲刷过程及冲刷深度发展历时,利用地形扫描仪测量冲刷后的床面形态,分析各工况下冲刷坑形态的差异,讨论影响套筒冲刷防护效果的主要因素。试验结果表明：套筒结构具有较好的防冲效果,本试验工况下,筒内冲刷深度最高可减小70%,筒内外最大冲刷深度可减小40%左右。套筒高度对筒内冲刷的影响比套筒直径更为显著,筒内最大冲刷深度随套筒高度的增大而减小。套筒直径主要影响筒外冲刷,套筒埋置于初始床面以上时,筒外最大冲刷深度随直径的增大而减小;随着套筒高度逐渐减小,直径对筒外冲刷的影响越来越小。     

单向流定床床面上水平管道周围流场与切应力分布特性

采用简化PIV方法,对悬空比G为0～1.6的单向流定床床面上水平圆柱绕流进行了系统的试验研究.通过对试验资料的分析,给出了圆柱绕流时的流场图和无量纲的床面、横管顶部和横管底部切应力的变化图,讨论了切应力随悬空比、管径、流速和水深的变化趋势.作者的研究成果有利于进一步研究海底管道的冲刷机理和冲刷坑的形成,进而有针对性的进行管道保护,减少管道破坏失效.     

港珠澳大桥青州航道桥桥墩基础冲刷试验研究

桥墩基础冲刷是桥梁毁坏的重要因素,是桥梁基础设计的关键指标之一。目前国内外对于桥墩基础在复杂动力条件下冲刷深度的研究常采用物理模型试验方法,利用正态系列模型方法,在波流水槽中研究了水流、潮流和波流共同作用下青州航道桥索塔基础周围流态变化和局部冲刷特征。研究结果表明,桥墩最大冲刷深度和冲淤范围与水流流速、桥墩轴线与水流夹角和波浪等因素有关;在潮流最大流速和恒定流流速一致情况下,桥墩局部冲刷深度达到平衡后,将会达到与恒定流基本一致的最大冲深;波流共同作用下的最大冲刷深度比恒定流增加10%左右。设计桥墩形状在100年一遇水流和波浪共同作用下桥墩基础局部最大冲刷深度为13.7 m。     

轴线倾斜海底管道冲刷速率试验研究

通过物理模型试验研究水流作用下轴线倾斜海底管道的三维局部冲刷问题。利用超声波探头监测管道下部冲刷沿管轴线方向的扩展过程,分析海底管道三维局部冲刷的动态发展机理。由模型沙的冲蚀试验,建立沙床面剪切应力与泥沙表观侵蚀速率之间的关系式,并引入经验公式对沙床面剪切应力放大系数、泥沙表观侵蚀速率以及远场床面剪切应力之间的关系进行表达。由倾斜管道模型试验,在分析冲刷扩展位置随时间变化数据的基础上,结合上述经验公式以及沙床面剪切应力放大系数与管道埋深的关系,建立轴线倾斜海底管道冲刷扩展速率的预测公式。     

新型旋转减冲装置对桩基局部冲刷防护试验研究

为减轻海上风电单桩基础周围局部冲刷对其结构安全的影响,提出了一种新型旋转减冲装置。在波流水槽中开展物理模型试验,改变波流条件、装置安装高度、安装距离,记录桩周冲刷发展历时,运用激光地形仪扫描冲刷坑形态,分析各工况下冲刷坑形态差异,验证装置不同安装距离、安装高度下的冲刷防护效果,提出了不同安装位置下的防护效率公式。结果表明：新型旋转减冲装置具有较好的冲刷防护效果,本试验工况下,桩周最大冲刷深度可减小44%左右。装置安装距离对冲刷防护效果影响较小,波流作用下的冲刷防护效果受装置安装高度影响显著,冲刷防护效果随装置安装高度的增加而减弱。     

基于Flow-3D的抗拖网海床基冲刷数值模拟

基于Flow-3D软件,建立抗拖网海床基沙土基床冲刷的三维数学模型,控制水流流速和泥沙粒径,对不同条件下抗拖网海床基周围沙土基床的冲刷进行数值模拟,并分析了抗拖网海床基最大冲刷深度随这两种因素改变的趋势。结果表明,抗拖网海床基沙土基床冲刷坑深度随海流流速增大而增加,在设定其他条件不改变的情况下,冲刷坑的加深速度随着流速增大会逐渐减缓,最终达到冲淤平衡。同时,由于海底环境复杂多变,导致模型与实际情况有一定的差异,还需在后续的研究中进一步进行优化。     

Onset of scour below pipelines and self-burial

This paper summarizes the results of an experimental study on the onset of scour below and self-burial of pipelines in currents/waves. Pressure was measured on the surface of a slightly buried pipe at two points, one at the upstream side and the other at the downstream side of the pipe, both in the sand bed. The latter enabled the pressure gradient (which drives a seepage flow underneath the pipe) to be calculated. The results indicated that the excessive seepage flow and the resulting piping are the major factor to cause the onset of scour below the pipeline. The onset of scour occurred always locally (but not along the length of the pipeline as a two-dimensional process). The critical condition corresponding to the onset of scour was determined both in the case of currents and in the case of waves. Once the scour breaks out, it will propagate along the length of the pipeline, scour holes being interrupted with stretches of soil (span shoulders) supporting the pipeline. As the span shoulder gets shorter and shorter, more and more weight of the pipeline is exerted on the soil. In this process, a critical point is reached where the bearing capacity of the soil is exceeded (general shear failure). At this point, the pipe begins to sink at the span shoulder (self-burial). It was found that the self-burial depth is governed mainly by the Keulegan–Carpenter number. The time scale of the self-burial process, on the other hand, is governed by the Keulegan–Carpenter number and the Shields parameter. Diagrams are given for the self-burial depth and the time scale of the self-burial process.     

Investigation of scour effect on tensile capacity of suction caissons considering stress history of sand

Abstract

Since the pull-out response of upwind caissons governs the design of multi-caisson foundations, it is worthwhile to study scour effect on the tensile capacity of suction caissons. The tensile capacity of suction caissons after scour is relevant to the scour depth and the pressure under the caisson lid: the tensile capacity decreases dramatically with increasing scour depth; the smaller the pressure, the stronger the weakening effect of scour. Moreover, the scour effect is investigated in two cases: ignoring stress history and considering stress history. The results show that tensile capacity after scour is larger when the stress history is considered, so ignoring the stress history leads to a conservative design. In order to quantitatively evaluate the effect of scour depth and pressure, an empirical formula for the tensile capacity of suction caissons after scour is proposed based on multiple regression analysis.     

Mechanism of local scour around submarine pipelines based on numerical simulation of turbulence model

1 IntroductionSubmarine pipelines are important ocean engi-neeringequipm ents, especiallyfortheoiland gasin-dustries. M anyresearchershavebeendedicatedtotheproblem of local scour around the submarinepipelines, butmostoftheirwork arelaboratory testsand foc…     

波、流及其共同作用下桩墩局部冲刷问题试验研究现状

要研究波流共同作用下桩墩的基础冲刷问题,首先需要了解水流和波浪单独作用下桩墩冲刷的机理和特征。针对波、流及其共同作用下桩墩的局部冲刷问题,从流速、水深、桩径、波长、波高、相对底层流速、粒径和粒径级配等方面系统地简述了恒定流、波浪和波流作用下桩、墩局部冲刷的研究进展。根据实验资料比较了各家经典计算公式的计算结果发现我国规范65-1式计算值偏大,65-2式计算值偏小等结论。桩墩局部冲刷是一个复杂的过程,今后可以针对淤泥质海岸底床、粉沙质海岸底床、复杂桩群结构、物理模型比尺效应、非恒定水动力条件、复杂基础形式方面对波流作用下基础冲刷的最大冲刷深度、冲刷过程、冲刷范围进行研究,以弥补桩墩局部冲刷在这些方面的不足。     

The effects of uniform and nonuniform pile spacing variations on local scour at pile groups

Pile groups are frequently used to support bridge decks. Scour in the vicinity of piles is the main cause for the bridges failure. In this research, to address the effects of uniform and nonuniform pile spacing on the equilibrium scour depth, laboratory experiments were carried out under steady clear-water conditions. For this purpose, scour depth produced by pile group with various pile spacing and arrangement was investigated using a laboratory flume. Flume bed was covered by uniform sediments with a median size of 0.9?mm and 0.2?m thickness. Flow discharge and velocity as well as scour depth were recorded in each experiment and the data were analyzed. The results showed that the pile spacing influences the local scour depth and with increase in uniform and transverse (perpendicular to the flow) spacing, the maximum scour depth was reduced. The pile spacing variation in line with the flow has a minor effect on scour depth. In addition, the pile spacing perpendicular to the flow was with the most influences on scour depth. The results of this research can be used by engineers to optimize the design of bridges.     

水流作用下斜桩局部冲刷及流场变化试验研究

为研究水流作用下斜桩周围局部冲刷特性及流场变化并掌握斜桩同垂直桩的差异,本研究在不同流速条件下开展了包含反斜桩、垂直桩、正斜桩等多种工况的水槽试验,测量分析了斜桩的冲刷历时曲线、床面形态、沿程流速分布、最大冲刷深度等数据.结果表明:清水条件下斜桩周围局部冲刷坑及桩后沙丘尺度明显减小;斜桩桩前最大冲刷深度随倾角的增加而逐...     

Large-scale laboratory experiment on erosion of sand beds by moving circular vertical jets

This study investigates the topographic deformation due to the erosion of a sand bed impinged by a moving submerged turbulent round jet in a large-scale laboratory. The test conditions represent the case of discharges beneath a vessel while operating in water with a limited clearance such as a shallow navigation channel. The jet moves horizontally and discharges water vertically downward towards the bed. The distance between the jet nozzle and the bed equals six times the jet diameter so the jet flow is in the potential core region. The speed of the jet horizontal motion was varied to examine its effect on the scour profile. The characteristic lengths of the scour profile in the asymptotic state were determined by modifying the empirical formulas in Aderibigbe and Rajaratnam [1996. Erosion of loose beds by submerged circular impinging vertical turbulent jets. Journal of Hydraulic Research 34(1), 19–33]. The maximum scour depth, the scour hole radius, and the ridge height were found to be a function of the ratio of the jet exit to jet translation velocities and were modeled using a hyperbolic function. Empirical equations describing the scour profile were developed and the scour profile was found to be self-similar when normalized by appropriate length scales.