Wave motion over a submerged breakwater with an upper horizontal porous plate and a lower horizontal solid plate

This study examines the hydrodynamic performance of a modified two-layer horizontal-plate breakwater. The breakwater consists of an upper submerged horizontal porous plate and a lower submerged horizontal solid plate. By means of the matched eigenfunction expansion method, a linear analytical solution is developed for the interaction of water waves with the structure. Then the reflection coefficient, the transmission coefficient, the energy-loss coefficient and the wave forces acting on the plates are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a single submerged horizontal solid plate and a single submerged horizontal porous plate. Numerical results show that with a suitable geometrical porosity of the upper plate, the uplift wave forces on both plates can be controlled at a low level. Numerical results also show that the transmission coefficient will be always small if the dimensionless plate length (plate length versus incident wavelength) exceeds a certain moderate value. This is rather significant for practical engineering, as the incident wavelength varies over a wide range in practice. Moreover, it is found that the hydrodynamic performance of the present structure may be further enhanced if the lower plate is also perforated.     

Wave reflection by a vertical wall with a horizontal submerged porous plate

By applying the linear water wave theory and the eigenfunction expansion method, the wave reflection by a vertical wall with a horizontal submerged porous plate is investigated in this paper. The numerical results, concerning the effects of the dimensionless plate length, the relative water depth, and the porous effect parameter of the plate on the wave loads on the plate and the wave height near the wall as well as the reflection coefficient, are discussed. It is found that the submerged plate increases the complexity of the phenomenon related to the wave reflection and refraction in the close region of the wall, and leads to the occurrence of the phenomenon of wave trapping. The results indicate that there may exist a process of focusing wave energy near the wall for small dimensionless porous effect parameters, whereas the increase of the dimensionless porous effect parameter decreases gradually the wave height until setdown occurs. The behavior of a larger plate with proper porosity is similar to that of a wave absorber which can significantly suppress not only the wave height above the plate but also the reflection waves. The ability of the porous plate to reduce the wave height on the wall surface is, in general, directly proportional to the dimensionless plate length and may be strongest for a proper value of the dimensionless porous effect parameter. It is also demonstrated that the wave loads on a porous plate are smaller than those on an impermeable plate.     

Forces and moment on a horizontal plate due to wave scattering

Wave reflection and transmission from a fixed horizontal plate have been widely studied but theoretical solutions are only available for certain limiting conditions. A general solution for this wave scattering problem is presented using the finite-element method, covering the whole range of relative depth ratio from shallow to deep water limits and submergence depth ratio from the water surface to the bed. Existing long-wave solutions for the surface plate and the submerged plate have been extended to obtain the hydrodynamic forces and overturning moment exerted on the plate. Results from the finite-element program compare well with these solutions. Variations of the reflection coefficient, wave forces and moment, with the plate width to wave length ratio, relative depth ratio and submergence depth ratio are discussed.     

Transmitted and reflected coefficients for horizontal or vertical plate type breakwater

Surface or submerged horizontal or vertical plate can be considered as a new concept breakwater.This paper investigates the wave-plate interaction of this type of breakwater by use of the boundary element method.The relationships of wave transmitted and reflected among plate thickness,submergence and length are carefully studied by numerical simulation.It is shown that:(1) The transmitted coefficients of submerged horizontal plate or vertical plate will become larger with the increase of plate thickness and reduce rapidly with the decrease of plate submergence.(2) Both surface horizontal and vertical plate are efficient for intermediate and short wave elimination,but vertical plate is more effective.(3) Submerged horizontal plate can act more effectively than submerged vertical plate does.With all wave frequencies,the vertical plate almost has no wave elimination effect.     

Wave motion over a breakwater system of a horizontal plate and a vertical porous wall

A two-dimensional analytical solution is presented to study the reflection and transmission of linear water waves propagating past a submerged horizontal plate and through a vertical porous wall. The velocity potential in each fluid domain is formulated using three sets of orthogonal eigenfunctions and the unknown coefficients are determined from the matching conditions. Wave elevations and hydrodynamic forces acting on the porous wall are computed. Reflection and transmission coefficients are presented to examine the performance of the breakwater system. The present analytical solutions are found in fairly good agreement with the available laboratory data. The results indicate that the plate length, the porous-effect, the gap between plate and porous wall, and the submerged depth of the plate all show a significant influence on the reflected and transmitted wave fields. It is also interesting to note that the submerged plate plays an important role in reducing the transmitted wave height, especially for long incident waves.     

Wave interaction with a perforated wall breakwater with a submerged horizontal porous plate

This study examines the hydrodynamic performance of a new perforated-wall breakwater. The breakwater consists of a perforated front wall, a solid back wall and a submerged horizontal porous plate installed between them. The horizontal porous plate enhances the stability and wave-absorbing capacity of the structure. An analytical solution based on linear potential theory is developed for the interaction of water waves with the new proposed breakwater. According to the division of the structure, the whole fluid domain is divided into three sub-domains, and the velocity potential in each domain is obtained using the matched eigenfunction method. Then the reflection coefficient and the wave forces and moments on the perforated front wall and the submerged horizontal porous plate are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a perforated-wall breakwater with a submerged horizontal solid plate [Yip, T.L., Chwang, A.T., 2000. Perforated wall breakwater with internal horiontal plate. Journal of Engineering Mechanics ASCE 126 (5), 533–538] and a vertical wall with a submerged horizontal porous plate [Wu, J.H., Wan, Z.P., Fang, Y., 1998. Wave reflection by a vertical wall with a horizontal submerged porous plate. Ocean Engineering 25 (9), 767–779]. Numerical results show that with suitable geometric porosity of the front wall and horizontal plate, the reflection coefficient will be always rather small if the relative wave absorbing chamber width (distance between the front and back walls versus incident wavelength) exceeds a certain small value. In addition, the wave force and moment on the horizontal plate decrease significantly with the increase of the plate porosity.     

水下平板与波浪相互作用完全非线性数值模拟(英文)

利用完全非线性数值波浪水槽技术研究水下平板与波浪的相互作用。假定水下平板厚度极薄、刚性,位于有限水深并且非常接近自由水面。应用四阶龙格库塔方法追踪每一时刻的波面形状,采用阻尼层来吸收反射波以保证算法的稳定性,同时引入平滑和重组的方法抑制自由表面控制点的较高梯度。通过对波浪与浮动圆柱相互作用的数值模拟证实了数值波浪水槽方法的有效性,计算结果与线性理论吻合良好。在波浪数值水槽方法中引入造波板模拟波浪产生并与水下平板发生相互作用,应用傅立叶解析方法对波面变形、波浪力作了分析。结果表明在板非常接近自由水面的情况下会表现出现很强的非线性,揭示了线性理论的局限性。     

没水倾斜板式防波堤消波性能分析

提出了一种将波浪中倾斜板问题等效化简为波浪中水平板单元组的方法,该方法建立在使用分离变量法求解水工结构边值问题的基础上,并使用伽辽金法精确求解连续边界条件,确定考虑衰减波态的速度势函数,从而求解没水倾斜板结构的消波性能。等效化简法计算精度于边界元法相当,且计算单元数量少、开销低。基于二维线性势波理论,对没水倾斜板式防波堤消波性能分析显示,没水板的倾斜角度、没水深度与板长是结构消波性能的控制因素:没水倾斜板防波堤的消波性能优于没水水平板防波堤的消波性能,随着没水板结构的倾斜角度增大,没水倾斜板结构的波浪透射系数显著减小,且长板优于短板,浅板优于深板;与前人的水槽实验对比显示,相对没水深度与波陡影响结构的消波性能,且波陡造成的波浪破碎贡献了显著的波能消耗。该结论对板式防波堤的结构配置、优化设计有重要意义。     

Wave force on vertically submerged circular thin plate in shallow water

The paper presented is a solution of shallow water wave force, using small amplitude linear wave theory on two-dimensional vertically submerged circular thin plates under three different configurations: (1) a surface-piercing circular thin plate, (2) a submerged circular thin plate, and (3) a bottom-standing circular thin plate. Finally Morison's equation is used for the determination of wave force which is based on the linear wave theory. The plate is submerged in water near the shore on uniformly sloping bottom. The solution method is confined in a finite domain, which contains both the region of different depth of water and the plate. Laplace's equation and boundary value problems are solved in a finite domain, by the method of separation of variables and the small amplitude linear wave theory. The variation of horizontal force by single particle, total horizontal force and moment with respect to the wave amplitude are obtained at different depth of water and at different wave period. It is observed that the force and moment are converging with the increase of wave period and the gradients of force and moment with respect to the wave amplitude are extremely high for lower wave period.     

Effect of a submerged plate on the near-bed dynamics underincoming waves in deep water conditions

It is well known that wave induced bottom oscillations become more and more negligible when the water depth exceeds half the wavelength of the surface gravity wave. However, it was experimentally demonstrated for regular waves that the bottom pressure oscillations at both first and second wave harmonic frequencies could be significant even for incoming waves propagating in deep water condition in the presence of a submerged plate [16]. For a water depth h of about the wavelength of the wave, measurements under the plate (depth immersion of top of plate h/6, length h/2) have shown bottom pressure variations at the wave frequency, up to thirty times larger than the pressure expected in the absence of the plate. In this paper, not only regular but also irregular wave are studied together with wave following current conditions. This behavior is numerically verified by use of a classical linear theory of waves. The wave bottom effect is explained through the role of evanescent modes and horizontally oscillating water column under the plate which still exist whatever the water depth. Such a model, which allows the calculation of the velocity fields, has shown that not only the bottom pressure but also the near bed fluid velocity are enhanced. Two maxima are observed on both sides of the location of the plate, at a distance of the plate increasing with the water depth. The possible impact of such near bed dynamics is then discussed for field conditions thanks to a scaling based on a Froude similarity. It is demonstrated that these structures may have a significant impact at the sea bed even in very deep water conditions, possibly enhanced in the presence of current.     

Wave transmission and reflection characteristics of a rigid surface and submerged horizontal plate

The wave transmission and reflection characteristics of a rigidly fixed surface and submerged horizontal plate were investigated experimentally in detail for a wide range of incident wave steepnesses and for different depths of submerge of the plate in deep water conditions in regular water wave fields. The experiments were conducted at the Ocean Engineering Centre, Indian Institute of Technology, Madras, India, in a wave flume 10 m long, 0.3 m wide and in a constant water depth of 0.8 m. The horizontal plate is 0.22 m thick and 1.2 m in length, covering the enrire width of the flume. From the present investigation, it is found that for a rigid surface plate, the coefficient of transmission is a minimum and the coefficient of reflection is a maximum, but the maximum value of the coefficient of energy loss occurs for plates submerged closer to the still-water level (SWL) and not for the surface plate. It is also found that the value of the coefficient of reflection increases with the increase in the value of the Reddy-Neelamani (RN) number, the ratio of horizontal water particle excursion at the bottom of the plate in its absence to the length of the plate. The coefficient of transmission is found to decrease rapidly with increase in the value of RN number up to 0.1. The wave transmission is only 5% for RN from 0.1 to 0.2. It is also found that for RN number greater than 0.04, the minimum energy dissipation is consistently about 60% of the incident wave energy.     

MPS Method for Interaction Between Solitary Waves and Submerged Horizontal Plate

The interaction between structure and wave is a typical phenomenon in naval architecture and ocean engineering. In this paper, numerical simulation is carried out to study the interaction between a two-dimensional submerged, fixed,horizontal rigid plate and solitary wave with our in-house meshless particle CFD solver MLParticle-SJTU. First, the in-house CFD solver is verified by experimental results conducted at the State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology. During the verification, the plate is submerged under water and the solitary wave with a given amplitude is generated by a piston-type wave maker. Free surface elevation of the wave and the pressure impacting on the plate is recorded and compared with experimental data respectively. The predicted pressure and surface elevation agree well with the experimental results. Then in order to further investigate factors affecting wave-structure interaction, wave height, submerged depth and plate length are analyzed.     

Scattering of water wave by a submerged horizontal plate and a submerged permeable breakwater

Based on a two-dimensional linear water wave theory, this study develops the boundary element method (BEM) to examine normally incident wave scattering by a fixed, submerged, horizontal, impermeable plate and a submerged permeable breakwater in water of finite depth. Numerical results for the transmission coefficients are also presented. In addition, the numerical technique's accuracy is demonstrated by comparing the numerical results with previously published numerical and experimental ones. According to that comparison, the transmission coefficient relies not only on the submergence of the horizontal impermeable plate and the height of the permeable breakwater, but also on the distance between horizontal plate and permeable breakwater. Results presented herein confirm that the transmission coefficient is minimum for the distance approximately equal to four times the water depth.     

The study of wave pressure and uplift force on a submerged plate

Boundary element method (BEM) is used to study wave pressure acting on a vertical quay, as well as the uplift forces on a submerged plate. The plate, placed in front of the quay, is bored with holes. The results are then compared with the case of a plate without any perforation.The results showed that: for q/h = 0.45, where q is the depth of submergence of the plate and h is water depth, wave pressure acting on the vertical quay is very similar for plates with or without borings. However, with q/h = 0.20, wave pressure on the quay is changed according to wave periods, widths of the plate, the distance of the plate away from the quay, as well as the ratio of the holes to the plates. Uplift forces exerted on the plate are indeed smaller for plates with borings than without, and decrease with increasing porous ratio. Furthermore, the uplift forces will be the same for the same porous ratios, regardless of these ratios being caused by a single or a double perforation.     

Study on scattering wave force of horizontal and vertical plate type breakwaters

The interaction between wave and horizontal and vertical plates is investigated by the boundary element method,and the relations of wave exciting force with plate thickness,submergence and length are obtained.It is found that:1) The efficient wave exciting force exists while plate submergence is less than 0.5 m,and the plate is very thin with order O(0.005 m).2) The maximum heave wave exciting force exists,and it is the main factor for surface and submerged horizontal plate while the roll force can be ignored.3) The maximum sway wave exciting force exists,it is the main factor for surface or submerged vertical plate,and the roll force is about 20 times of horizontal plate.     

Wave Radiation by A Submerged Ring Plate in Water of Finite Depth

A plate submerged at a certain depth underneath the sea surface has been proposed as a structure type for different purposes, including motion response reduction, wave control, and wave energy harvesting. In the present study, the three-dimensional wave radiation problem is investigated in the context of the linear potential theory for a submerged ring plate in isolation or attached to a floating column as an appendage. In the latter case, the ring plate is attached at a certain distance above the column bottom. The structure is assumed to undergo a heave motion. An analytical model is developed to solve the wave radiation problem via the eigenfunction expansion method in association with the region-matching technique. With the velocity potential being available, the hydrodynamic coefficients, such as added mass and radiation damping, are obtained through the direct pressure integration. An alternative solution of radiation damping has also been developed in this study, in which the radiation damping is related to the Kochin function in the wave radiation problem. After validating the present model, numerical analysis is performed in detail to assess the influence of various plate parameters, such as the plate size and submergence depth. It is noted that the additional added mass due to the attached ring plate is larger than that when the plate is in isolation. Meanwhile, the radiation damping of the column for the heave motion can vanish at a specific wave frequency by attaching a ring plate, corresponding to a condition that there exist no progressive waves in the exterior region.     

Scattering of water wave by a submerged horizontal plate and a submerged permeable breakwater

Based on a two-dimensional linear water wave theory, this study develops the boundary element method (BEM) to examine normally incident wave scattering by a fixed, submerged, horizontal, impermeable plate and a submerged permeable breakwater in water of finite depth. Numerical results for the transmission coefficients are also presented. In addition, the numerical technique's accuracy is demonstrated by comparing the numerical results with previously published numerical and experimental ones. According to that comparison, the transmission coefficient relies not only on the submergence of the horizontal impermeable plate and the height of the permeable breakwater, but also on the distance between horizontal plate and permeable breakwater. Results presented herein confirm that the transmission coefficient is minimum for the distance approximately equal to four times the water depth.     

Interaction of linear waves with an array of infinitely long horizontal circular cylinders in a two-layer fluid of infinite depth

The linear water wave scattering and radiation by an array of infinitely long horizontal circular cylinders in a two-layer fluid of infinite depth is investigated by use of the multipole expansion method. The diffracted and radiated potentials are expressed as a linear combination of infinite multipoles placed at the centre of each cylinder with unknown coefficients to be determined by the cylinder boundary conditions. Analytical expressions for wave forces, hydrodynamic coefficients, reflection and transmission coefficients and energies are derived. Comparisons are made between the present analytical results and those obtained by the boundary element method, and some examples are presented to illustrate the hydrodynamic behavior of multiple horizontal circular cylinders in a two-layer fluid. It is found that for two submerged circular cylinders the influence of the fluid density ratio on internal-mode wave forces is more appreciable than surface-mode wave forces, and the periodic oscillations of hydrodynamic results occur with the increase of the distance between two cylinders; for four submerged circular cylinders the influence of adding two cylinders on the wave forces of the former cylinders is small in low and high wave frequencies, but the influence is appreciable in intermediate wave frequencies.     

Breaking solitary wave evolution over a porous underwater step

Solitary wave evolution over a shelf including porous damping is investigated using Volume-Averaged Reynolds Averaged Navier–Stokes equations. Porous media induced damping is determined based on empirical formulations for relevant parameters, and numerical results are compared with experimental information available in the literature. The aim of this work is to investigate the effect of wave damping on soliton disintegration and evolution along the step for both breaking and non-breaking solitary waves. The influence of several parameters such as geometrical configuration (step height and still water level), porous media properties (porosity and nominal diameter) or solitary wave characteristics (wave height) is analyzed. Numerical simulations show the porous bed induced wave damping is able to modify wave evolution along the step. Step height is observed as a relevant parameter to influence wave evolution. Depth ratio upstream and downstream of the edge appears to be the more relevant parameter in the transmission and reflection coefficients than porosity or the ratio of wave height–water depth. Porous step also modifies the fission and the solitary wave disintegration process although the number of solitons is observed to be the same in both porous and impermeable steps. In the absence of breaking, porous bed triggers a faster fission of the incident wave into a second and a third soliton, and the leading and the second soliton reduces their amplitude while propagating. This decrement is observed to increase with porosity. Moreover, the second soliton is released before on an impermeable step. Breaking process is observed to dominate over the wave dissipation at the porous bottom. Fission is first produced on a porous bed revealing a clear influence of the bottom characteristics on the soliton generation. The amplitude of the second and third solitons is very similar in both impermeable and porous steps but they evolved differently due to the effect of bed damping.     

Interaction of ocean waves with floating and submerged horizontal flexible structures in three-dimensions

A three-dimensional general mathematical hydroelastic model dealing with the problem of wave interaction with a floating and a submerged flexible structure is developed based on small amplitude wave theory and linear structural response. The horizontal floating and submerged flexible structures are modelled with a thin plate theory. The linearized long wave equations based on shallow water approximations are derived and results are compared. Three-dimensional Green’s functions are derived using fundamental source potentials in water of finite and infinite depths. The expansion formulae associated with orthogonal mode-coupling relations are derived based on the application of Fourier transform in finite and infinite depths in case of finite width in three-dimensions. The usefulness of the expansion formula is demonstrated by analysing a physical problem of surface gravity wave interaction with a moored finite floating elastic plate in the presence of a finite submerged flexible membrane in three-dimensions. The numerical accuracy of the method is demonstrated by computing the complex values of reflected wave amplitudes for different modes of oscillation and mooring stiffness. Further, the effect of compressive force and modes of oscillations on a free oscillation hydroelastic waves in a closed channel of finite width and length for floating and submerged elastic plate system is analysed.