流体对石灰岩断层摩擦滑动影响的实验研究

在气体介质三轴高温岩石力学实验仪器上,采用意大利Scaglia Bianca石灰岩,在温度50～300℃、围压150MPa,含50MPa孔隙压、无孔隙压含饱和水和完全干燥三种条件下,开展摩擦滑动实验.实验力学数据和显微结构表明,完全干燥样品在120℃时出现慢滑移,实验样品中没有出现溶解与沉淀.无孔隙压含饱和水条件下,100℃、120℃、150℃条件下出现典型的慢滑移,实验样品中含有微弱的溶解与沉淀;300℃条件下出现黏滑,实验样品中出现沉淀.在含50MPa孔隙压条件下,50℃时的实验表现为典型的稳滑,实验样品中以溶解为主;在100～150℃时,出现慢滑移,实验样品中以溶解为主,沉淀为辅;在200～300℃时,出现典型黏滑,实验样品中以沉淀为主.实验结果表明,石灰岩断层泥摩擦滑动稳定性随温度变化,受流体中碳酸钙的溶解和沉淀作用控制,因此,流体中矿物质的饱和度这一化学性质对断层带的摩擦强度和摩擦滑动稳定性具有显著影响.     

白云母对岩盐断层带摩擦速度依赖性影响的实验研究

为更好地理解层状硅酸盐对断层强度、滑动速度依赖性及地震活动特征的影响,利用双轴摩擦实验对含白云母岩盐断层带在干燥及含水条件下摩擦的速度依赖性进行了实验研究,并观测了摩擦滑动过程中的声发射,分析了断层带的微观结构.实验结果表明,干燥条件下含白云母岩盐断层带在0.1 ～ 100μm/s的速度范围内表现为黏滑和速度弱化,增大σ2会使断层带从速度弱化向速度强化转化,速度依赖性转换出现在0.1 μm/s,其中断层滑动表现为稳滑或应力释放时间较长的黏滑事件;含水条件下含白云母岩盐断层带在0.05 ～0.01μm/s的速度范围内表现为速度强化,0.1 ～10μm/s的速度范围内表现为速度弱化,50～100μm/s的速度范围内又转换为速度强化行为.含白云母岩盐断层带在干燥条件下一次黏滑伴随一个或一丛声发射事件,而在含水条件下与稳滑相对应,滑动过程中并未记录到声发射事件.显微结构观察表明,速度弱化域的主要变形机制是岩盐颗粒的脆性破裂和局部化的滑动;干燥条件下,速度强化域的主要变形机制是岩盐颗粒的均匀破裂;含水条件下2个速度强化域对应不同的微观机制,高速域的速度强化受控于岩盐颗粒在白云母相互连结形成的网状结构上的滑动及其均匀碎裂作用,而低速域的速度强化还受岩盐的压溶作用控制.通过与岩盐断层带摩擦实验结果对比可知,白云母的存在对于燥岩盐断层带摩擦滑动方式和速度依赖性没有显著影响,而在含水条件下白云母的存在使得岩盐断层带滑动趋于稳定.实验结果为分析含层状硅酸盐断层的强度和稳定性提供了依据.此外,在速度依赖性转换域上观察到的应力缓慢释放的现象进一步证实了在岩盐断层带摩擦滑动过程中观察到的现象,这对慢地震机制研究具有参考意义.     

THE GEOLOGICAL AND ROCK MECHANICAL DISTINCTION EVIDENCE BETWEEN STICK-SLIP AND CREEP IN HOST ROCK SEGMENTS OF FAULT

Paleo-seismic and fault activity are hard to distinguish in host rock areas compared with soft sedimentary segments of fault. However, fault frictional experiments could obtain the conditions of stable and unstable slide, as well as the microstructures of fault gouge, which offer some identification marks between stick-slip and creep of fault. We summarized geological and rock mechanical distinction evidence between stick-slip and creep in host rock segments of fault, and analyzed the physical mechanisms which controlled the behavior of stick-slip and creep. The chemical composition of fault gouge is most important to control stick-slip and creep. Gouge composed by weak minerals, such as clay mineral, has velocity weakening behavior, which causes stable slide of fault. Gouge with rock-forming minerals, such as calcite, quartz, feldspar, pyroxene, has stick-slip behavior under condition of focal depth. To the gouge with same chemical composition, the deformation mechanism controls the frictional slip. It is essential condition to stick slip for brittle fracture companied by dilatation, but creep is controlled by compaction and cataclasis as well as ductile shear with foliation and small fold. However, under fluid conditions, pressure solution which healed the fractures and caused strength recovery of fault, is the original reason of unstable slide, and also resulted in locking of fault with high pore pressure in core of fault zone. Contrast with that, rock-forming minerals altered to phyllosilicates in the gouges by fluid flow through degenerative reaction and hydrolysis reaction, which produced low friction fault and transformations to creep. The creep process progressively developed several wide shear zones including of R, Y, T, P shear plane that comprise gouge zones embedded into wide damage zones, which caused small earthquake distributed along wide fault zones with focal mechanism covered by normal fault, strike-slip fault and reverse fault. However, the stick-slip produced mirror-like slide surfaces with very narrow gouges along R shear plane and Y shear plane, which caused small earthquake distributed along narrow fault zones with single kind of focal mechanism.     

Rock friction-effect of confining pressure,temperature, and pore pressure

This paper reviews many of the mechanical properties of faulted and jointed rock under pressure and temperature and in the presence of water. At low effective confining pressures (below about 1 kilobar), the friction strength is quite variable and depends on the frictional resistance between gouge particles or asperities and on the dilatancy of the fault. At higher pressures the friction strength is nearly independent of mineralogy, temperature, and rate, at least for rocks whose friction strength is less than the failure strength. Water tends to slightly weaken the fault. The type of sliding motion, whether stick-slip or stable sliding, is much more affected by environmental and mineralogical factors. In general, stick-slip is dominant at high pressures and low temperatures, in the presence of strong minerals such as quartz and feldspar, in the absence of gouge, for lower surface roughness, and perhaps in the presence of water. The microscopic deformation mechanisms are poorly understood. At low temperatures, cataclasis dominates in rocks containing mostly quartz or feldspar, and plastic deformation in rocks containing mostly calcite or platy silicates. At high temperature most minerals deform plastically, producing a greater temperature-and rate-dependence of the friction strength. Glass has been found in some sliding surfaces in sandstone.     

Effect of Sliding Rate on the Activity of Acoustic Emission During Stable Sliding

--The mechanical and statistical characteristics of acoustic emission (AE) events during stable sliding are investigated through a laboratory experiment using a granite specimen with a pre-cut fault. Numerous AE events are found to be generated on the pre-cut fault, indicating that microscopically unstable fracture occurs during macroscopically stable sliding. The composite focal mechanism solution of AE events is determined from the first motion directions of P-waves. The determined mechanism is consistent with the double-couple one expected for the slip on the pre-cut fault. The source radii of large AE events are estimated to be about 10 mm from the widths of the first P-wave pulses. These indicate that the AE events are generated by shear fracture whose faulting area is a part of the pre-cut fault plane. The occurrence of AE events as a stochastic process approximately obeys the Poisson process, if the effect of mutually dependent events consti tuting clusters is corrected. The observed amplitude-frequency relation of AE events approximately follows a power law for a limited amplitude range. As the macroscopic sliding rate increases, the number of AE events per unit sliding distance decreases. This rate dependence of the AE activity is qualitatively consistent with the observation that the real area of contact between sliding surfaces decreases with an increase in the sliding rate as reported in the literature.     

岩盐断层带摩擦滑动的速度依赖性转换及其地震学意义

为了深入理解断层带摩擦滑动速度依赖性转换及其机制,利用双轴摩擦实验对干燥及含水条件下岩盐断层带摩擦的速度依赖性进行了实验研究,并观测了摩擦滑动过程中的声发射,分析了断层带的微观结构.实验结果表明,干燥岩盐断层带在0.1~100 μm/s的速度范围内表现为速度弱化,增大σ₂会使断层带向速度强化转变;含水条件下岩盐断层带在1~100 μm/s的速度范围内表现为速度弱化,而在0.1~0.01 μm/s的速度范围内表现为速度强化,速度依赖性转换出现在0.1~1 μm/s,其中断层表现为振荡或应力释放时间较长的黏滑事件;岩盐断层带在干燥条件下表现出很强的声发射活动,每个黏滑均对应一丛声发射事件,而在含水条件下一次黏滑只对应一个声发射事件.显微观察表明,局部化的脆性破裂是速度弱化域的主要变形机制,分布式的碎裂流动是干燥岩盐断层带在速度强化域的变形机制,颗粒边界迁移以及压溶作用的塑性变形是含水条件下岩盐断层带在速度强化域的主要变形机制,而脆性破裂和塑性变形共同控制着速度依赖性转换域断层带的变形.水的存在促进岩盐发生塑性变形,进而导致断层带从速度弱化向速度强化转换.上述结果有助于理解断层带上地震活动的特征和慢地震的机制.     

Granular Controls on Periodicity of Stick-Slip Events: Kinematics and Force-Chains in an Experimental Fault

It is a long-standing question whether granular fault material such as gouge plays a major role in controlling fault dynamics such as seismicity and slip-periodicity. In both natural and experimental faults, granular materials resist shear and accommodate strain via interparticle friction, fracture toughness, fluid pressure, dilation, and interparticle rearrangements. Here, we isolate the effects of particle rearrangements on granular deformation through laboratory experiments. Within a sheared photoelastic granular aggregate at constant volume, we simultaneously visualize both particle-scale kinematics and interparticle forces, the latter taking the form of force-chains. We observe stick-slip deformation and associated force drops during an overall strengthening of the shear zone. This strengthening regime provides insight into granular rheology and conditions of stick-slip periodicity, and may be qualitatively analogous to slip that accompanies longer term interseismic strengthening of natural faults. Of particular note is the observation that increasing the packing density increases the stiffness of the granular aggregate and decreases the damping (increases time-scales) during slip events. At relatively loose packing density, the slip displacements during the events follow an approximately power-law distribution, as opposed to an exponential distribution at higher packing density. The system exhibits switching between quasi-periodic and aperiodic slip behavior at all packing densities. Higher packing densities favor quasi-periodic behavior, with a longer time interval between aperiodic events than between quasi-periodic events. This difference in the time-scale of aperiodic stick-slip deformation is reflected in both the kinematics of interparticle slip and the force-chain dynamics: all major force-chain reorganizations are associated with aperiodic events. Our experiments conceptually link observations of natural fault dynamics with current models for granular stick-slip dynamics. We find that the stick-slip dynamics are consistent with a driven harmonic oscillator model with damping provided by an effective viscosity, and that shear-transformation-zone, jamming, and crackling noise theories provide insight into the effective stiffness and patterns of shear localization during deformation.     

FRICTIONAL PROPERTIES OF A NATURAL FAULT GOUGE FROM DRILLED CORES IN THE LONGMENSHAN FAULT ZONE CUTTING GRANITIC ROCK

In this paper, we report friction experiments performed on natural fault gouge samples embedded in granitic rock from drilled core by a project entitled "the Longmenshan Fault Shallow Drilling(LMFD)". Compared with other natural fault gouge, this yellow-greenish gouge(YGG)is dominantly chlorite-rich. The maximum content of chlorite reaches 47%in the YGG. To understand the frictional properties of the YGG sample, experiments were performed at constant confining pressure of 130MPa, with constant pore pressure of 50MPa and at different temperatures from 25℃ to 150℃. The experiments aim to address the frictional behavior of the YGG under shallow, upper crustal pressure, and temperature conditions. Compared with previous studies of natural gouge, our results show that the YGG is stronger and shows a steady state friction coefficient of 0.47~0.51. Comparison with previous studies of natural gouge with similar content of clay minerals indicates a sequence of strengths of different clay minerals:chlorite > illite > smectite. At temperatures up to 150℃ hence depths up to~8km in the Longmenshan region, the YGG shows stable velocity-strengthening behavior at shallow crustal conditions. Combined with the fact of strong direct velocity effect, i.e., (a-b)/a>0.5, faults cutting the present clastic lithology up to~8km depth in the Longmenshan fault zone(LFZ)are likely to offer stable sliding resistance, damping co-seismic rupture propagating from below at not-too-high slip rates. However, as the fault gouge generally has low permeability, co-seismic weakening through thermal pressurization may occur at high slip rates(>0.05m/s), leading to additional hazards.     

Analysis of stick-slip and earthquake mechanism

A mathematical model of a sliding system that contains a frictional surface embedded in an elastic specimen and machine is proposed to analyze the frictional behavior observed in laboratory and field. It is shown that stick-slip occurs if the slope of the velocity-stress relation on the sliding surface exceeds a critical value at a certain point between static and kinetic frictions. This condition, coupled with Amontons' law and other subsidiary relations, predicts the effects of normal stress, gouge thickness, temperature, and loading rate etc. on the stick-slip instability, consistent with known experimental evidence. The elastic-wave radiation associated with stick-slip is governed by Brune's source time function, in which rise time and effective stress are proportional to fault dimension and stress drop, respectively.     

拐折断层黏滑过程的实验研究

采用位移、应变和声发射等测量手段,研究了预置5°拐折断层的房山花岗岩样品的黏滑过程,分析了不同加载速率下5°拐折断层失稳的黏滑特征及相关物理场的演化过程。实验结果表明: 1)5°拐折断层的黏滑周期与加载速率在数值上呈负对数相关关系; 2)在不同的加载速率下,大多数的5°拐折断层失稳是双震事件, 2次子事件的间隔时间大多在100～200ms之间; 3)采用不同的观测手段,即使采样速率一致,其临震响应也存在差异性,如断层失稳前沿断层的应变测量结果呈现明显的应变弱化,断层位移则未见明显的变化; 4)断层黏滑过程中的声发射事件呈现明显的沿断层迁移的特征。认识强震的发生机理和余震特征需要进一步研究断层失稳过程的动力学信息。     

Development of shear localization in simulated quartz gouge: Effect of cumulative slip and gouge particle size

Frictional sliding experiments were conducted on two types of simulated quartz gouge (with median particle diameters 5 m and 25 m, respectively) at confining pressures ranging from 50 MPa to 190 MPa in a conventional triaxial configuration. To investigate the operative micromechanical processes, deformation texture developed in the gouge layer was studied in samples which had accumulated different amounts of frictional slip and undergone different stability modes of sliding. The spatial patterning of shear localization was characterized by a quantitative measurement of the shear band density and orientation. Shear localization in the ultrafine quartz gouge initiated very early before the onset of frictional sliding. Various modes of shear localization were evident, but within the gouge zoneR ₁-shears were predominant. The density of shear localization increased with cumulative slip, whereas the angle subtended at the rock-gouge interface decreased. Destabilization of the sliding behavior in the ultrafine quartz gouge corresponded to the extension ofR ₁-shears and formation of boundaryY-shear segments, whereas stabilization with cumulative slip was related to the coalescence ofY-shear segments to form a throughgoing boundary shear. In the coarse quartz gouge, the sliding behavior was relatively stable, probably because shear localization was inhibited by distributed comminution. Two different models were formulated to analyze the stress field within the gouge zone, with fundamentally different predictions on the orientations of the principal stresses. If the rock-gouge interface is assumed to be bonded without any displacement discontinuity, then the maximum principal stress in the gouge zone is predicted to subtend an angle greater than 45° at the interface. If no assumption on displacement or strain continuity is made and if the gouge has yielded as a Coulomb material, then the maximum principal stress in the gouge zone is predicted to subtend an angle less than 45°. If the apparent friction coefficient increases with overall slip (i.e., slip-hardening), then the Riedel shear angle progressively decreases with increasing shear strain within the gouge layer, possibly attaining a zero value which corresponds to a boundaryY-shear. Our quantitative data on shear localization orientation are in reasonable agreement with this second model, which implies the coefficient of internal friction to be about 0.75 for the ultrafine quartz gouge and 0.8 for the coarse gouge. The wide range of orientations for Riedel shear localization observed in natural faults suggests that the orientations of principal stresses vary as much as in an experimental gouge zone.     

剪切破裂与粘滑——浅源强震发震机制的研究

周口店花岗闪长岩的高温高压三轴实验和理论分析表明,剪切破裂和摩擦滑移具有类似的孕育过程和发生机制。剪切破裂贯通强度就是一种摩擦强度。剪切破裂和摩擦滑移各自都有渐进式和突发式之分。突发式摩擦滑移是已有断层的粘滑滑移。突发式剪切破裂则是完整岩石的初始粘滑滑移。考虑到地壳温度随深度增加,完整岩石剪裂强震要求较高的围压,因此,多数浅源强震的发震方式很可能是已有断层的粘滑     

AN EXPERIMENTAL STUDY ON THE PROCESS OF INTERGRANULAR PRESSURE SOLUTION OF PLAGIOCLASE GOUGE UNDER HIGH TEMPERATURE AND PRESSURE: METHOD AND PRELIMINARY RESULTS

To understand the mechanism of lower-crust earthquake and slow slips, it is necessary to study the frictional properties of mafic rocks and their major rock-forming minerals. Previous studies have performed a series of experimental researches on gabbro, basalt and their major constituents. According to the results of previous experiments, frictional sliding of plagioclase under hydrothermal conditions(100~600℃)shows a property of velocity weakening, and the experimental results show that both the direct rate effect parameter(a)and the healing effect parameter(b)increase with temperature, a typical feature for thermally-activated processes. Velocity weakening means property of a shear band that has a stronger friction healing effect than the direct rate effect in the rate and state friction constitutive framework, and the healing effect(b value)in constitutive relation mainly reflects the increase in contact area with time under hydrothermal conditions, with some minor effect of structural changes. Since the microphysical mechanism of feldspar minerals at the contacts is mainly brittle cataclasis for temperatures below 600℃, the significant frictional healing effect in this case can only be explained by the mechanism of pressure solution. In order to determine if the dissolution process of plagioclase actually occurs on the laboratory time scale, we conducted hydrostatic experiments on plagioclase powder samples under hydrothermal conditions whereby frequent contact switch between particles seen in frictional sliding experiments can be avoided, making the observation on the dissolution sites possible. Experimental temperatures were 400℃ and 500℃, with confining pressure of 90~150MPa, pore pressure of 30MPa, with 2mm initial thickness of fault gouge. The mechanical data show that a creep process occurred in the plagioclase fault gouge in the experimental temperature and pressure range; and the microstructures of the experiment show that precipitation of new grains is prevalent as the product of pressure solution process between plagioclase particles. At the same time, it is observed that the contact points have an appearance similar to fused, fuzzy structure as signatures of dissolution. The results of our experiments provide a definite experimental evidence for the healing mechanism in friction of plagioclase and for the theoretical relation between unstable slip and the pressure solution process. The results of the experiments are summarized as follows: (1)Drainage rate of pore water in plagioclase gouge was high in the first few hours of experiment, but gradually decreases over time for both temperature and pressure series of experiments slowing down to a steady state. This feature indicates that there is a creep process that evolves inside the plagioclase gouge. In the temperature-series experiments, the drainage rate of the pore water in the plagioclase gouge at 400℃ is relatively low than the cases for higher temperatures. Thus, the applied temperature is positively correlated with the creep of plagioclase gouge. (2)Scanning electron microscopy(SEM)observations of the experimentally deformed samples were performed on thin sections cut along the sample axis. Firstly, from the images of microstructure, it was found that the degree of particle fracture became more significant at a higher effective pressure, with smaller pore volume between particles. In the temperature-series experiments it was found that the degree of compaction of plagioclase gouge increased with increasing temperature. Precipitation of plagioclase grains in layered structures was generally observed in high-magnification images, indicating the presence of pressure solution processes. Contact points were also found to be in a state of ambiguity that seems to be a fused morphology, but the details of the structure remain to be determined by further observations. The above results indicate that the pressure solution process of plagioclase particles can occur on a typical laboratory time scale, and the results of this study provide robust experimental evidences for the theory that links between pressure solution and the mechanism of frictional healing and unstable slips for plagioclase.     

水对断层摩擦滑动稳定性的影响

在不同含水条件下研究了光面、含脆性物质夹层和含延性物质夹层 3类断层的摩擦滑动行为 ,认为水对断层滑动稳定性和摩擦滑动的速度依赖性有重要影响。建立了含有岩性、围压 (深度 )和含水量 3因素的断层活动稳定性的模式 ,认为脆性断层更多地表现为速度弱化 ,少量水的存在易于出现黏滑 ,高孔隙压时会表现为稳滑 ;半脆性或半延性的断层在少量水或较低孔隙压的情况下会表现出速度弱化 ,也就可能出现黏滑 ,但孔隙压较高后 ,会表现出速度强化 ,滑动也就会是稳定的 ;延性断层多为速度强化 ,不出现黏滑。提出水的进入降低了系统的稳定性 ,水的存在增加了系统的稳定性。这是考虑水或一般流体对岩体或断层活动稳定性影响时需要考虑的两个方面     

硬石膏断层带摩擦稳定性转换与微破裂特征的实验研究

断层带摩擦稳定性转换及其对应的微破裂特征对于地震成核条件和慢地震机理研究具有重要的意义.本文利用双轴实验装置研究了硬石膏断层带摩擦稳定性的转换及其对应的应变变化、微破裂特征,并分析了实验标本的微观结构.实验结果表明,σ₂和加载点速度对断层滑动稳定性具有显著影响.在低σ₂条件下,硬石膏断层带出现不稳定滑动,变形以局部化的脆性破裂和摩擦为主;随σ₂的增加,断层由不稳定滑动向稳定滑动转换,断层带变形方式逐渐转变为分布式的破裂.在低σ₂条件下,硬石膏断层带在较低加载点速度下表现为速度强化且滑动稳定,在中等加载点速度下表现为速度弱化并伴有准周期性的黏滑,在较高加载点速度下又有转向速度强化的趋势,σ₂的提高使得速度弱化的范围逐渐减少,滑动趋于稳定.上述两次转换对应不同的微破裂特征,在较高速度下从速度弱化转换为速度强化时,断层滑动伴有能量较小但频度很高的微破裂活动,而在较低速度下从速度弱化转换为速度强化时,断层滑动伴有间歇性的微破裂,这与断层带的微观结构特征有较好的对应关系,表明其转换机制是不同的.     

海原断裂带断层泥摩擦特性的研究

用双剪法对海原断裂带5个点的13种断层泥的摩擦滑动特征进行的实验研究表明,海原断裂带的断层泥的存在有助于消除粘滑与增大摩擦强度,五个点断层泥的摩擦系数平均值分别是0.760(景泰),0.728(哈思山),0.669(大沟门),0.644(剌儿沟),0.684(蔡祥堡)。     

Some properties of unstable slip on rough surfaces

In this paper we report results obtained from various friction experiments under direct and oblique shear loading conditions. We used four rock types of varying brittleness (quartzite, anhydrite, limestone, pyrophyllite) with different surface roughness. The observations concentrate on the time span several milliseconds before dynamic failure occurs. During this period a premonitory, unstable phase of slip (slip 2) occurs. This differs importantly from a premonitory, stable process (slip 1) with durations of hundreds of seconds. On smooth surfaces slip 2 is usually observed with ductile rocks and less reliably with brittle rocks. Slip 2 is mostly accompanied by acoustic emissions, which increase in rate of occurrence and in magnitude until the stick-slip event. Foreshocks are observed during approximately 50% of the slip 2 events on rough surfaces. Foreshocks far exceed the acoustic noise level, which is also prevalent before stick-slip events on rough surfaces. In the direct shear experiment, where two faults are being loaded simultaneously, in about 20% of the cases precursory slip 2 was observed on the opposite side on which the final stick-slip event occurred.     

Effect of fault jogs on frictional behavior: An experimental study

Studying the effect of geometrically irregular bodies on the mechanical behavior of fault activity is of significance in understanding the seismic activity along a fault zone. By using rock mechanics ex- periment with medium-scale samples, we have studied the effect of fault jogs, the most common irregularity along fault zones, on frictional behavior. The research indicates that extensional fault jog can be easily fractured because of its low strength and the fractured jog has no obvious resistance to fault sliding, and the micro-fractures occurring in the jog are indicative of stick-slip along the faults. The fault zone containing extensional jogs is characterized by velocity weakening and can be described by rate and state friction law. Compressional fault jog makes fault sliding more difficult because of its high fracturing strength, but the micro-fractures occurring in the tensile areas around fault ends at higher stress level can provide necessary condition for occurrence of stick-slip along the faults before the jog is fractured and thus act as precursors of fault instability. Compression jog can be taken as a stable indicator of fault segmentation until the jog is completely fractured and two faults are linked.     

Seismic measurements of the internal properties of fault zones

The internal properties within and adjacent to fault zones are reviewed, principally on the basis of laboratory, borehole, and seismic refraction and reflection data. The deformation of rocks by faulting ranges from intragrain microcracking to severe alteration. Saturated microcracked and mildly fractured rocks do not exhibit a significant reduction in velocity, but, from borehole measurements, densely fractured rocks do show significantly reduced velocities, the amount of reduction generally proportional to the fracture density. Highly fractured rock and thick fault gouge along the creeping portion of the San Andreas fault are evidenced by a pronounced seismic low-velocity zone (LVZ), which is either very thin or absent along locked portions of the fault. Thus there is a correlation between fault slip behavior and seismic velocity structure within the fault zone; high pore pressure within the pronounced LVZ may be conductive to fault creep. Deep seismic reflection data indicate that crustal faults sometimes extend through the entire crust. Models of these data and geologic evidence are consistent with a composition of deep faults consisting of highly foliated, seismically anisotropic mylonites.