Degradation of dimethyl sulfoxide through fluidized-bed Fenton process: kinetic analysis

In this study, fluidized-bed Fenton process (FBF) was used to degrade dimethyl sulfoxide (DMSO), one of the most widely used solvents. Oxidation by Fenton’s reagent, Fe⁺² and H₂O₂, is one of the cheapest advanced oxidation processes due to the high availability of the reagents. FBF is a modified approach that reduces the large amount of iron oxide sludge formed in conventional Fenton process. The optimal treatment efficiencies by FBF with 2 h of reaction were 95.22 % of DMSO degradation and 34.38 % of COD removal at the conditions of 5 mM DMSO, 68.97 g/L SiO₂ carrier, pH_initial 3.0, 5 mM Fe²⁺, and 32.5 mM H₂O₂. The kinetic study was also done to investigate the two stages involved in the oxidation. The first stage fitted the zero reaction order with overall initial rate’s apparent rate constant, k ₁, of ?0.099. The second stage fitted the first order of DMSO degradation, with rate constant, k ₂, of ?0.0005.     

Redox state of deep off-craton lithospheric mantle: new data from garnet and spinel peridotites from Vitim, southern Siberia

Oxygen fugacity (fO₂) affects melting, metasomatism, speciation of C–O–H fluids and carbon-rich phases in the upper mantle. fO₂ of deep off-craton mantle is poorly known because garnet-peridotite xenoliths are rare in alkali basalts. We examine the redox and thermal state of the lithospheric mantle between the Siberian and North China cratons using new Fe³⁺/ΣFe ratios in garnet and spinel obtained by M?ssbauer spectroscopy, major element data and P–T estimates for 22 peridotite xenoliths as well as published data for 15 xenoliths from Vitim, Russia. Shallow spinel-facies mantle is more oxidized than deep garnet peridotites (average, ?0.1 vs. ?2.5 ΔlogfO₂(FMQ)). For intermediate garnet–spinel peridotites, fO₂ estimates from spinel-based oxybarometers are 1.5–3.2 ΔlogfO₂(FMQ) lower than those from garnet-based oxybarometers. These rocks may be out of phase and chemical inter-mineral equilibrium because the spinel–garnet reaction and concomitant changes in mineral chemistry do not keep up with P–T changes (e.g., lithospheric heating by recent volcanism) due to slow diffusion of trivalent cations and because gar-, gar-spl and spl-facies rocks may coexist on centimeter–meter scale. The spinel-based fO₂ estimates may not be correct while garnet-based fO₂ values provide conditions before the heating. The T (780–1,100?°C) and fO₂ ranges of the Vitim xenoliths overlap those of coarse garnet and spinel cratonic peridotites. However, because of a higher geothermal gradient, the deepest Vitim garnet peridotites are more reduced (by 0.5–2.0 ΔlogfO₂(FMQ)) than cratonic garnet peridotites at similar depths, and the “water maximum” conditions (>80?% H₂O) in the off-craton mantle exist in a more shallow and narrow depth range (60–85?km) than in cratonic roots (100–170?km). The base of the off-craton lithospheric mantle (≥90?km) at 2.5?GPa and 1,150?°C has fO₂ of ?3.0 ?logfO₂(FMQ), with dominant CH₄ and H₂O and minor H₂ in the fluid. Melting near the base of off-craton mantle lithosphere may be induced by increasing water share in migrating fluids due to oxidation of methane.     

Oxygen isotope partitioning during oxidation of pyrite by H2O2 and its dependence on temperature

A detailed experimental study was conducted to investigate mechanisms of pyrite oxidation by determining product yields and oxygen isotopic fractionation during reactions between powdered pyrite (FeS₂) with aqueous hydrogen peroxide (H₂O₂). Sealed silica-tube experiments utilized aliquots of pyrite that were reacted with 0.2 M H₂O₂ for 7 to 14 days at 4 to 150 °C. No volatile sulfur species were detected in any experiment. The only gaseous product recovered was elemental oxygen inferred to result from decomposition of H₂O₂. Aqueous sulfate (S_aq) was the only sulfur product recovered from solution. Solid hydrated ferric iron sulfates (i.e., water-soluble sulfate fraction, S_ws) were recovered from all experiments. Ferric oxide (hematite) was detected only in high temperature experiments.Reactants were selected with large differences in initial δ¹⁸O values. The oxygen isotopic compositions of oxygen-bearing reactants and products were analyzed for each experiment. Subsequent isotopic mass-balances were used to identify sources of oxygen for reaction products and to implicate specific chemical reaction mechanisms. δ¹⁸O of water did not show detectable change during any experiment. δ¹⁸O of sulfate was similar for S_aq and S_ws and indicated that both H₂O and H₂O₂ were sources of oxygen in sulfate. Low-temperature experiments suggest that H₂O-derived oxygen was incorporated into sulfate via Fe³⁺ oxidation, whereas H₂O₂-derived oxygen was incorporated into sulfate via oxidation by hydroxyl radicals (HO). These two competing mechanisms for oxygen incorporation into sulfate express comparable influences at 25 °C. With increasing reaction temperatures from 4 to 100 °C, it appears that accelerated thermal decomposition and diminished residence time of H₂O₂ limit the oxygen transfer from H₂O₂ into sulfate and enhance the relative importance of H₂O-derived oxygen for incorporation into sulfate. Notably, at temperatures between 100 and 150 °C there is a reversal in the lower temperature trend resulting in dominance of H₂O₂-derived oxygen over H₂O-derived oxygen. At such high temperatures, complete thermal decomposition of H₂O₂ to water and molecular oxygen (O₂) occurs within minutes in mineral-blank experiments and suggests little possibility for direct oxidation of pyrite by H₂O₂ above 100 °C. We hypothesize that a Fe-O₂ mechanism is responsible for oxygenating pyrite to sulfate using O₂ from the preceding thermal decomposition of H₂O₂.     

Pollution reduction and biodegradability index improvement of tannery effluents

Al₂ (SO₄)3, 18H₂O, FeCl₃ and Ca (OH)₂ were used for the treatment of tannery wastewaters. The influences of pH and coagulant dosages were studied. Conditions were optimised according to the pollutant removal efficiencies, the volume of decanted sludge and the biodegradability index improvement. The results indicate that 67–71% of total COD, 76–92% of color and 79–97% of Cr can be removed using the optimum coagulant dosages at the optimum pH range. Al₂ (SO₄)₃, 18H₂O and Ca (OH)₂ produced better results than FeCl₃ in terms of COD, color and Cr removal as well as in terms of biodegradability improvement. Moreover, Al₂ (SO₄)₃, 18H₂O and FeCl₃ produced the least amount of sludges for a given amounts of COD, color and Cr removed in comparison with Ca (OH)₂. Al₂ (SO₄)₃, 18H₂O seems to be suitable for yielding high pollutant removals and corresponding low volumes of decanted sludges in addition to improving wastewaters biodegradability index.     

The relevance of bisphenol A adsorption during Fenton’s oxidation

The aim of this research was to assess the efficiency of Fenton’s oxidation for degradation of endocrine disruptor bisphenol A (BPA) with emphasis on extent of accompanying adsorption. Adsorption on the waste sludge resulting from the Fenton’s oxidation could represent a significant impact on the final removal efficiency of BPA. Fenton’s oxidation was accomplished at two concentrations of BPA (0.228 and 22.8 mg L^?1); both at the selected molar ratio of reagents Fe²⁺:H₂O₂ (1:10), as a function of reaction time. The kinetics of adsorption of BPA on waste sludge was determined for the same two concentrations of BPA at two concentrations of waste sludge (0.1 and 6.0 g L^?1). In addition to changing concentrations of BPA and sludge, the adsorption process was also influenced by parameters such as temperature, pH and contact time. Adsorption isotherms were determined. Oxidation and adsorption were monitored by gas chromatography combined with mass spectrum. It has been confirmed that BPA is not completely oxidized in Fenton’s oxidation, because it is adsorbed to formed waste ferric sludge and thus necessary precautions for sludge deposition must be observed.     

Bildungsbedingungen von Al-Fe (III)-Epidoten

Relations between the composition of Al-Fe(III)-epidotes and the Fe content and oxidation ratio of a series of metamorphic rocks from the Hohen Tauern area, Tyrol (Austria), were investigated. The Fe(III) content of the epidotes depends on the oxidation ratio Fe(III)×100/(Fe(III)+ Fe(II)) of the rocks. The Fe(III) content of the epidotes as well as the oxidation ratio decreases within the series from greenschist to almandin-amphibolite facies. The relation between epidote composition and oxidation ratio can be explained by the following redox reactions: 6 Fe(III) Al₂ Ep+6 Mu+6 Qz+6 Hä+n Ab ? (1a) (12 An+n Ab) Plag+6 Bio+3 H₂O+4 1/2O₂. 6 Fe(III) Al₂ Ep+6 Mu+6 Qz+n Ab ? (1b) (12 An+n Ab) Plag+2 Bio+4 Kf+7 H₂O+1 1/2O₂. These reactions are in good agreement with the observed mineral assemblages and may explain the increase of the An content of coexisting plagioclase with increasing metamorphic grade.     

Role of Fe(II) and phosphate in arsenic uptake by coprecipitation

Natural attenuation of arsenic by simple adsorption on oxyhydroxides may be limited due to competing oxyanions, but uptake by coprecipitation may locally sequester arsenic. We have systematically investigated the mechanism and mode (adsorption versus coprecipitation) of arsenic uptake in the presence of carbonate and phosphate, from solutions of inorganic composition similar to many groundwaters. Efficient arsenic removal, >95% As(V) and ∼55% in initial As(III) systems, occurred over 24 h at pHs 5.5-6.5 when Fe(II) and hydroxylapatite (Ca₅(PO₄)₃OH, HAP) “seed” crystals were added to solutions that had been previously reacted with HAP, atmospheric CO_2(g) and O_2(g). Arsenic adsorption was insignificant (<10%) on HAP without Fe(II). Greater uptake in the As(III) system in the presence of Fe(II) was interpreted as due to faster As(III) to As(V) oxidation by molecular oxygen in a putative pathway involving Fe(IV) and As(IV) intermediate species. HAP acts as a pH buffer that allows faster Fe(II) oxidation. Solution analyses coupled with high-resolution transmission electron microscopy (HRTEM), X-ray Energy-Dispersive Spectroscopy (EDS), and X-Ray Absorption Spectroscopy (XAS) indicated the precipitation of sub-spherical particles of an amorphous, chemically-mixed, nanophase, Fe^III[(OH)₃(PO₄)(As^VO₄)]·nH₂O or Fe^III[(OH)₃( PO₄)(As^VO₄)(As^IIIO₃)_minor]·nH₂O, where As^IIIO₃ is a minor component.The mode of As uptake was further investigated in binary coprecipitation (Fe(II) + As(III) or P), and ternary coprecipitation and adsorption experiments (Fe(II) + As(III) + P) at variable As/Fe, P/Fe and As/P/Fe ratios. Foil-like, poorly crystalline, nanoparticles of Fe^III(OH)₃ and sub-spherical, amorphous, chemically-mixed, metastable nanoparticles of Fe^III[(OH)₃, PO₄]·nH₂O coexisted at lower P/Fe ratios than predicted by bulk solubilities of strengite (FePO₄·2H₂O) and goethite (FeOOH). Uptake of As and P in these systems decreased as binary coprecipitation > ternary coprecipitation > ternary adsorption.Significantly, the chemically-mixed, ferric oxyhydroxide-phosphate-arsenate nanophases found here are very similar to those found in the natural environment at slightly acidic to circum-neutral pHs in sub-oxic to oxic systems, such phases may naturally attenuate As mobility in the environment, but it is important to recognize that our system and the natural environment are kinetically evolving, and the ultimate environmental fate of As will depend on the long-term stability and potential phase transformations of these mixed nanophases. Our results also underscore the importance of using sufficiently complex, yet systematically designed, model systems to accurately represent the natural environment.     

Impact of natural organic matter on H2O2-mediated oxidation of Fe(II) in a simulated freshwater system

The oxidation of Fe(II) by H₂O₂ has been studied in the presence of Suwannee River fulvic acid, a standard form of natural organic matter, by adding inorganic Fe(II) to solutions containing both H₂O₂ and fulvic acid and monitoring the total Fe(II) concentration using a luminol chemiluminescence method. At pH 8.4 and in the absence of competing metals, Suwannee River fulvic acid significantly retards the rate of Fe(II) oxidation due to gradual formation of a species that is oxidized more slowly than inorganic Fe(II) by both O₂ and H₂O₂. It is suggested that rapid formation of a weak Fe(II)-fulvic acid complex that is not readily oxidized by H₂O₂ is the cause of the reduction in the initial oxidation rate, and that the subsequent further reduction in oxidation rate is a result of the formation of a second type of Fe(II)-fulvic acid complex that is resistant to both O₂ and H₂O₂ oxidation. A kinetic model has been developed that supports this conceptual model. The results demonstrate that, under certain conditions, natural organic matter may stabilize Fe(II) in the presence of elevated H₂O₂ concentrations, significantly increasing the lifetime of ferrous iron and reducing the flux of hydroxyl radicals produced through this oxidation pathway.     

Solubility and solution mechanism of H2O in alkali silicate melts and glasses at high pressure and temperature

The solubility behavior of H₂O in melts in the system Na₂O-SiO₂-H₂O was determined by locating the univariant phase boundary, melt = melt + vapor in the 0.8-2 GPa and 1000°-1300°C pressure and temperature range, respectively. The NBO/Si-range of the melts (0.25-1) was chosen to cover that of most natural magmatic liquids. The H₂O solubility in melts in the system Na₂O-SiO₂-H₂O (X_H2O) ranges between 18 and 45 mol% (O = 1) with (∂X_H2O/∂P)_T∼14-18 mol% H₂O/GPa. The (∂X_H2O/∂P)_T is negatively correlated with NBO/Si (= Na/Si) of the melt. The (∂X_H2O/∂T)_P is in the −0.03 to +0.05 mol% H₂O/°C range, and is negatively correlated with NBO/Si. The [∂X_H2O/∂(NBO/Si)]_P,T is in the −3 to −8 mol% H₂O/(NBO/Si) range. Melts with NBO/Si similar to basaltic liquids (∼0.6-∼1.0) show (∂X_H2O/∂T)_P<0, whereas more polymerized melts exhibit (∂X_H2O/∂T)_P>0. Complete miscibility between hydrous melt and aqueous fluid occurs in the 0.8-2 GPa pressure range for melts with NBO/Si ≤0.5 at T >1100°C. Miscibility occurs at lower pressure the more polymerized the melt.     

Hydration of rhyolitic glass during weathering as characterized by IR microspectroscopy

The mechanism and rate of hydration of rhyolitic glass during weathering were studied. Doubly polished thin sections of two rhyolites with different duration of weathering (Ohsawa lava: 26,000 yr, Awanomikoto lava: 52,000 yr) were prepared. Optical microscope observation showed that altered layers had developed along the glass surfaces. IR spectral line profile analysis was conducted on the glass sections from the surface to the interior for a length of 250 μm and the contents of molecular H₂O (H₂O_m), OH species (OH) and total water (H₂O_t) were determined. The diffusion profile of H₂O_m in Ohsawa lava extends beyond the layer observed by optical microscope. The content of H₂O_m in the hydrated region is much higher than that of OH species. Thus, the reaction from H₂O_m to OH appears to be little and H₂O_m is the dominant water species moving into the glass during weathering. Based on the concentration profiles, the diffusion coefficients of H₂O_m(D_H2Om) and H₂O_t(D_H2Ot) were determined to be 2.8 × 10⁻¹⁰ and 3.4 × 10⁻¹⁰ μm² s⁻¹ for Ohsawa lava, and 5.2 × 10⁻¹¹ and 4.1 × 10⁻¹¹ μm² s⁻¹ for Awanomikoto lava, respectively. The obtained D_H2Om during weathering are more than 2-3 orders of magnitude larger than the diffusion coefficient at ∼20 °C that is extrapolated from the diffusivity data for >400 °C. This might suggest that the mechanism of water transport is different at weathering conditions and >400 °C.     

Kinetics of H2-O2-H2O redox equilibria and formation of metastable H2O2 under low temperature hydrothermal conditions

Hydrothermal experiments were conducted to evaluate the kinetics of H_2(aq) oxidation in the homogeneous H₂-O₂-H₂O system at conditions reflecting subsurface/near-seafloor hydrothermal environments (55-250 °C and 242-497 bar). The kinetics of the water-forming reaction that controls the fundamental equilibrium between dissolved H_2(aq) and O_2(aq), are expected to impose significant constraints on the redox gradients that develop when mixing occurs between oxygenated seawater and high-temperature anoxic vent fluid at near-seafloor conditions. Experimental data indicate that, indeed, the kinetics of H_2(aq)-O_2(aq) equilibrium become slower with decreasing temperature, allowing excess H_2(aq) to remain in solution. Sluggish reaction rates of H_2(aq) oxidation suggest that active microbial populations in near-seafloor and subsurface environments could potentially utilize both H_2(aq) and O_2(aq), even at temperatures lower than 40 °C due to H_2(aq) persistence in the seawater/vent fluid mixtures. For these H₂-O₂ disequilibrium conditions, redox gradients along the seawater/hydrothermal fluid mixing interface are not sharp and microbially-mediated H_2(aq) oxidation coupled with a lack of other electron acceptors (e.g. nitrate) could provide an important energy source available at low-temperature diffuse flow vent sites.More importantly, when H_2(aq)-O_2(aq) disequilibrium conditions apply, formation of metastable hydrogen peroxide is observed. The yield of H₂O_2(aq) synthesis appears to be enhanced under conditions of elevated H_2(aq)/O_2(aq) molar ratios that correspond to abundant H_2(aq) concentrations. Formation of metastable H₂O₂ is expected to affect the distribution of dissolved organic carbon (DOC) owing to the existence of an additional strong oxidizing agent. Oxidation of magnetite and/or Fe⁺⁺ by hydrogen peroxide could also induce formation of metastable hydroxyl radicals (•OH) through Fenton-type reactions, further broadening the implications of hydrogen peroxide in hydrothermal environments.     

Mineralogic and sulfur isotopic effects accompanying oxidation of pyrite in millimolar solutions of hydrogen peroxide at temperatures from 4 to 150 °C

Oxidation of pyrite by hydrogen peroxide (H₂O₂) at millimolar levels has been studied from 4 to 150 °C in order to evaluate isotopic effects potentially associated with radiolytic oxidation of pyrite. Gaseous, aqueous, and solid phases were collected and measured following sealed-tube experiments that lasted from 1 to 14 days. The dominant gaseous product was molecular oxygen. No volatile sulfur species were recovered from any experiment. Sulfate was the only aqueous sulfur species detected in solution, with sulfite and thiosulfate below the detection limits. X-ray diffraction patterns and images from scanning electron microscopy reveal solid residues composed primarily of hydrated ferric iron sulfates and sporadic ferric-ferrous iron sulfates. Hematite was detected only in solid residue produced during high temperature experiments. Elemental sulfur and/or polysulfides are inferred to be form on reacting pyrite surface based on extraction with organic solvents. Pyrite oxidation by H₂O₂ increases in rate with increasing H₂O₂concentration, pyrite surface area, and temperature. Rates measured in sealed-tube experiments at 25°C, for H₂O₂ concentration of 2 × 10⁻³ M are 8.8 × 10⁻⁹ M/m²/sec, which are higher than previous estimates. A combination of reactive oxygen species from H₂O₂ decomposition products and reactive iron species from pyrite dissolution is inferred to aggressively oxidize the receding pyrite surface. Competing oxidants with temperature-dependent oxidation efficiencies results in multiple reaction mechanisms for different temperatures and surface conditions. Sulfur isotope values of remaining pyrite were unchanged during the experiments, but showed distinct enrichment of ³⁴S in produced sulfate and depletion in elemental sulfur. The Δ_{sulfate-pyrite} and Δ_{elemental sulfur-pyrite} was +0.5 to +1.5‰ and was −0.2 to −1‰, respectively. Isotope data from high-temperature experiments indicate an additional ³⁴S-depleted sulfur fraction, with up to 4‰ depletion of ³⁴S, in the hematite. Sulfur isotope trends were not influenced by H₂O₂ concentration, temperature, or reaction time. Results of this study indicate that radiolytically produced oxidants, such as hydrogen peroxide and hydroxyl radicals, could efficiently oxidize pyrite in an otherwise oxygen-limited environment. Although H₂O₂ is generally regarded as being of minor geochemical significance on Earth, the H₂O₂ molecule plays a pivotal role in Martian atmospheric and soil chemistry. Additional experimental and field studies are needed to characterize sulfur and oxygen isotope systematics during radiolytical oxidation of metallic sulfides and elemental sulfur.     

Water speciation and diffusion in haploandesitic melts at 743-873 K and 100 MPa

Water is an important volatile component in andesitic eruptions and deep-seated andesitic magma chambers. We report an investigation of H₂O speciation and diffusion by dehydrating haploandesitic melts containing ?2.5 wt.% water at 743-873 K and 100 MPa in cold-seal pressure vessels. FTIR microspectroscopy was utilized to measure species [molecular H₂O (H₂O_m) and hydroxyl group (OH)] and total H₂O (H₂O_t) concentration profiles on the quenched glasses from the dehydration experiments. The equilibrium constant of the H₂O speciation reaction H₂O_m+O?2OH, K = (X_OH)²/(X_H2OmX_O) where X means mole fraction on a single oxygen basis, in this Fe-free andesite varies with temperature as ln K = 1.547-2453/T where T is in K. Comparison with previous speciation data on rhyolitic and dacitic melts indicates that, for a given water concentration, Fe-free andesitic melt contains more hydroxyl groups. Water diffusivity at the experimental conditions increases rapidly with H₂O concentration, contrary to previous H₂O diffusion data in an andesitic melt at 1608-1848 K. The diffusion profiles are consistent with the model that molecular H₂O is the diffusion species. Based on the above speciation model, H₂O_m and H₂O_t diffusivity (in m²/s) in haploandesite at 743-873 K, 100 MPa, and H₂O_t ? 2.5 wt.% can be formulated as

     

Pollution characteristics of polycyclic aromatic hydrocarbons （PAHs） in oily sludge from the Zhongyuan Oilfield and its peripheral soils

The purpose of this study is to determine the degree of contamination caused by polycyclic aromatic hydrocarbons (PAHs) in oily sludge and soils around it in the Zhongyuan Oilfield. The contents of polycyclic aromatic hydrocarbons in oily sludge samples were determined with HPLC. The contents of PAHs of oily sludge from three different oil production plants vary from high to low in the order of the Wenming oily sludge dumping site of No. 3 Oil Production Plant (3W)>the Mazhai oily sludge dumping site of No. 3 Oil Production Plant (3M)>the Wen’er oily sludge dumping site of No. 4 Oil Production Plant (4W). Naphthalene, acenaphthylene, acenaphthene, fluorine and phenanthrene are the major pollutants of PAHs in oily sludge. The contents of PAHs in soil samples around the oily sludge dumping sites vary widely from 434.49 to 2408.8 ng/g. Naphthalene, acenaphthene, fluorine, phenanthrene and pyrene are the characteristic factors of PAHs in soil samples of 3M and 3W, and naphthalene, acenaphthene, fluorine and phenanthrene are the characteristic factors of PAHs in soil samples of 4W. According to these data and the ratios of Fl/Py, PAHs in oily sludge samples come mainly from petrogenic sources, and soil samples are divided into petrogenic soil samples and mixed-source soil samples, and both petrogenic and pyrogenic soil samples in terms of the sources of PAHs. The classification by Nemero index P indicates that soils around the oily sludge dumping sites have been seriously polluted.     

Biosorption with autochthonous and allochthonous fungal biomasses for bioremediation and detoxification of landfill leachate

Landfill leachates are not adequately treated in traditional wastewater treatment plants, on account of their problematic peculiarities: i.e., dark colour, high concentration of recalcitrant pollutants and COD, and high toxicity. In this work, 19 biomasses (15 autochthonous and 4 allochthonous) were exploited in biosorption treatment for the remediation of a leachate (influent) and the effluent coming from the biological oxidation with activated sludge and nitrification–denitrification treatment. The effects of the initial pH, the biomass amount, and the medium for the biomass pre-culture were considered. The best configuration was: pH 5, 5 g L^??1 biomass cultivated on STY medium. Eventually, the two most effective biomasses, Cunninghamella bertholletiae MUT 2861 and Aspergillus fumigatus MUT 4050, were used in consecutive 2 h cycles in a batch biosorption experiment. The effectiveness of the treatment decreased in subsequent cycles in terms of decolourisation (31–15%). COD, Cl^?, SO₄^2?, total N, and toxicity were removed mainly in the second cycle of treatment (up to ??36, ??12, ??15, ??17 and ??49%, respectively). The results suggest that the effluent toxicity was basically due to uncoloured substances, which were mainly removed after coloured molecules.     

Decolorization of simulated spent reactive dye bath using solar / TiO2 / H2O2

Different parameters were investigated to evaluate their effect on the process removal efficiency of reactive dye from simulated spent reactive dye bath, by solar / TiO₂ / H₂O₂, including H₂O₂ concentration, TiO2 loading and pH. As a result 99% of reactive dye can be removed at a TiO₂ loading of 400mg/l, H₂O₂ concentration of 150 mg/l and of pH: 5.2. The effect of photo-catalytic deactivation of TiO₂ on reactive dye removal was studied for ten number of cycles, and found that the extent of deactivation was high for each consecutive repeated use.     

Oxidation of Sb(III) to Sb(V) by O2 and H2O2 in aqueous solutions

The rates of Sb(III) oxidation by O₂ and H₂O₂ were determined in homogeneous aqueous solutions. Above pH 10, the oxidation reaction of Sb(III) with O₂ was first order with respect to the Sb(III) concentration and inversely proportional to the H⁺ concentrations at a constant O₂ content of 0.22 × 10⁻³ M. Pseudo-first-order rate coefficients, k_obs, ranged from 3.5 × 10⁻⁸ s⁻¹ to 2.5 × 10⁻⁶ s⁻¹ at pH values between 10.9 and 12.9. The relationship between k_obs and pH was:

     

Pyrite (FeS2) oxidation: A sub-micron synchrotron investigation of the initial steps

Pyrite is an environmentally significant mineral being the major contributor to acid rock drainage. Synchrotron based SPEM (scanning photoelectron microscopy) and micro-XPS (X-ray photoelectron spectroscopy) have been used to characterise fresh and oxidised pyrite (FeS₂) with a view to understanding the initial oxidation steps that take place during natural weathering processes. Localised regions of the pyrite surface containing Fe species of reduced coordination have been found to play a critical role. Such sites not only initiate the oxidation process but also facilitate the formation of highly reactive hydroxyl radical species, which then lead the S oxidation process.Four different S species are found to be present on fresh fractured pyrite surfaces: S₂²⁻_(bulk) (4-fold coordination), S₂²⁻_(surface) (3-fold coordination), S²⁻ and S⁰/S_n²⁻ (metal deficient sulfide and polysulfide respectively). These species were found to be heterogeneously distributed on the fractured pyrite surface. Both O₂ and H₂O gases are needed for effective oxidation of the pyrite surface. The process is initiated when O₂ dissociatively and H₂O molecularly adsorb onto the surface Fe sites where high dangling bond densities exist. H₂O may then dissociate to produce OH radicals. The adsorption of these species leads to the formation of Fe-oxy species prior to the formation of sulfoxy species. Evidence suggests that Fe-O bonds form prior to Fe-OH bonds. S oxidation occurs through interactions of OH radicals formed at the Fe sites, with formation of SO₄²⁻ occurring via S₂O₃²⁻/SO₃²⁻ intermediates. The pyrite oxidation process is electrochemical in nature and was found to occur in patches, where site specific adsorption of O₂ and H₂O has occurred. Fe and S oxidation was found to occur within the same area of oxidation probably in atomic scale proximity. Furthermore, the O in SO₄²⁻ arises largely from H₂O; however, depending on the surface history, SO₄²⁻ formed early in the oxidation process may also contain O from O₂.     

Crystallization conditions of peraluminous charnockites: constraints from mineral thermometry and thermodynamic modelling

Most igneous charnockites are interpreted to have crystallized at hot and dry conditions, i.e. at >800?°C and <3 wt.% H₂O and with an important CO₂ component in the system. These charnockites are metaluminous to weakly peraluminous and their formation involves a significant mantle-derived component. This study, in contrast, investigates the crystallization conditions of strongly peraluminous, metasediment-sourced charnockites from the Qinzhou Bay Granitic Complex, South China. To constrain the temperature-melt H₂O crystallization paths for the studied peraluminous charnockites, petrographic characterization was combined with fluid inclusion compositional data, mineral thermometry, and thermodynamic modelling. The uncertainties of the thermodynamic modelling in reconstructing the crystallization conditions of the granitic magmas have been evaluated by comparison between modelled and experimental phase relations for a moderately evolved, peraluminous granite (~70 wt.% SiO₂). The comparison suggests that the modelling reproduces the experimentally derived phase saturation boundaries with uncertainties of 20–60?°C and 0.5–1 wt.% H₂O for systems with ≤1–2 wt.% initial melt H₂O at ~0.2 GPa. For the investigated natural systems, the thermometric estimates and modelling indicate that orthopyroxene crystallized at relatively low temperature (750–790?±?30?°C) and moderately high to high melt H₂O content (3.5–5.6?±?0.5 wt.%). The charnockites finally solidified at relatively “cold” and “wet” conditions. This suggests that thermodynamic modelling affords a possible approach to constrain charnockite crystallization as tested here for peraluminous, moderately low pressure (≤0.3 GPa), and overall H₂O-poor systems (≤1–2 wt.% H₂O total), but yields results with increasing uncertainty for high-pressure or H₂O-rich granitic systems.     

Mössbauer effect study of anapaite, Ca2Fe2+(PO4)2 · 4H2O, and of its oxidation products

Mössbauer spectra (MS) of anapaite (Ca₂ Fe²⁺(PO₄)₂?·?4H₂O) and of a sample after being immersed in a 4% H₂O₂ solution at room temperature (RT) over 12 days (hereafter an4ox) were collected at temperatures in the range 4.2 to 420?K and 11 to 300?K respectively. All MS consist of symmetrical doublets, hence magnetic ordering was not observed. The temperature dependencies of the Fe²⁺ centre shifts of anapaite and an4ox were analysed with the Debye model for the lattice vibrations. The characteristic Mössbauer temperatures were found as 370?K?±?25?K and 340?K?±?25?K, and the intrinsic isomer shifts as 1.427?±?0.005?mm/s and 1.418?±?0.005?mm/s respectively. From the external-field (60?kOe) MS recorded at 4.2 and 189?K for the non-treated sample, the principal component V _zz of the electric field gradient (EFG) is determined to be positive and the asymmetry parameter η?≈?0.2 and 0.4 respectively. The temperature variations of the quadrupole splittings, ΔE _Q(T), cannot be interpreted on the basis of the thermal population of the ⁵ D electronic levels resulting from the tetragonal compression of the O₆ co-ordination. The low-temperature linear behaviour of ΔE _Q(T) is attributed to a strong orbit-lattice coupling. A field of 60 kOe applied to anapaite at 4.2?K produces magnetic hyperfine splitting with effective hyperfine fields of ?136, ?254 and ?171?kOe along the principal axes Ox, Oy and Oz of the EFG tensor respectively. Additional oxidation treatments in solutions with various H₂O₂ concentrations up to 20% and subsequent Mössbauer experiments at room temperature, have revealed that the anapaite structure is not sensitive to oxidation since eventually only a small amount of Fe²⁺ (～6.5%) is converted into Fe³⁺.