天津滨海场地土动力学参数研究

天津滨海地区是典型的软土区,属晚第四系以来的浅海相沉积软土。本文收集了该地区地震安全性评价报告中的土动力学参数的实验资料,并补充了15个钻孔的测试实验,统计分析了淤泥质粘土、淤泥质粉质粘土、粉土、粉质粘土、粘土、粉砂、细砂等7种土类的实测土动力学参数,给出了它们在不同深度下的动剪切模量比和阻尼比的统计值。然后,选取了2个典型钻孔并建立了土层地震反应分析模型,分别运用本文统计值、94规范值和袁晓铭等(2000)的推荐值进行土层地震反应计算,从反应谱形状、地表峰值加速度和反应谱特征周期等方面说明了本文统计值的适用性和针对性。本文的研究成果对天津滨海地区各类工程建设的场地地震安全性评价工作具有一定的借鉴和参考价值,且有利于该地区工程场地地震安全性评价工作的开展。     

大连地区场地土动力学参数初步研究

In this paper, dynamic soil parameters derived from Dalian area seismic risk assessment reports are collected. In this study, the measurement data is divided into 7 types, i.e. silty clay, muddy silty clay, clay, medium sand, rock fragments, backfill soil and fully-weathered slate. Statistics of the dynamic parameters of these soils are carried out to obtain the mean values of dynamic shear modulus ratio and damping ratio. Typical drill holes are selected to establish dynamic soil models to investigate the seismic response for various cases. The dynamic parameters of the models are taken from the statistical values of this study, the standard values of code 94 (i.e. the dynamic soil parameters for Dalian seismic microzonation), and the recommended values by Yuan Xiaoming et al. (2000) respectively. The calculated results of peak ground acceleration are compared with the response spectral characteristics. The results show that the statistical values are approximate to the values recommended by Yuan Xiaoming, et al. (2000), but different greatly with the standard values in code 94.     

大连地区场地土动力学参数初步研究

通过收集近年来大连地区地震安全性评价报告中土动力学参数的实验资料,统计分析粉质粘土、淤泥质粉质粘土、粘土、中砂、碎石、回填土和全风化板岩等7类土的实测动力学参数,给出了它们的动剪切模量比和阻尼比的统计值.然后,选取典型钻孔并建立了土层地震反应分析模型,分别运用本文统计值、94规范值(即原大连地震小区划的土动力学参数值)和袁晓铭等(2000)的推荐值进行土层地震反应计算,并将计算结果中的地表峰值加速度和反应谱形状进行了比较.结果表明,本文的统计值与袁晓铭等( 2000)的推荐值非常接近,而与94规范值有很大的差别.     

四川盆地场地土动力学参数统计研究

四川盆地地震构造环境相对稳定,主要遭受近场中强地震和外围大地震的影响。盆地内第四系主要为河流相的砂卵石层夹粘土、粉土层,分布于成都平原及盆地内外河流两岸。这种地层在土层地震反应计算时往往产生一个峰值,具有显著的放大作用。本文收集共计123组土动力学参数的实验资料,统计分析了淤泥质土、粉质粘土、粘土、粉土、细砂和全风化泥岩等6种土类实测土动力学参数,给出了它们在不同深度下的动剪切模量比和阻尼比的统计值。并且将统计值和"94"规范值与袁晓铭推荐值[9]进行了对比分析,结果表明在盆地内使用规范值和推荐值会对工程的抗震设防产生不利影响。该研究成果对盆地内各类工程建设的工程场地地震安全性评价工作具有一定的借鉴和参考价值。     

天津地区覆盖层土动力学参数统计分析

收集天津地区近年来有代表性的具有完整土动力学参数作为实验数据的地震安全性评价报告66份,用两种统计方法按不同深度统计分析粉质黏土、黏土、粉土、砂土、淤泥质土等的实测土动力学参数,给出动剪切模量比和阻尼比平均值。选取2个典型工程场地,构建土层分析模型,进行土层地震反应分析计算。结果表明,本文得到的统计2值在天津地区具有一定的代表性和适用性,与实测值结果更为接近。对于获得原状土样困难的场地,特别是对于较薄的夹层土,可参照统计2结果进行分析计算。     

成都平原粘性土动力学参数统计分析

成都平原地震构造环境主要受近场中强地震和外围大地震的影响。成都平原内的第四系分布广泛,主要为河流相的砂卵石层夹粘土、粉土层。这种地层在土层地震反应计算时往往会产生一个峰值,具有显著的放大作用。本文共收集了107组土动力学参数的实验资料,统计分析了粉质粘土和粘土两种粘性土的实测土动力学参数,给出了它们在不同深度的动剪切模量比和阻尼比的统计值。然后,选取1个典型钻孔,建立了土层地震反应分析模型,分别运用本文"统计值"、"十五结果"、"规范值"、"推荐值"进行地震土层反应计算,从反应谱形状、地表峰值加速度和反应谱特征周期等方面,验证了本文"统计值"的适用性和针对性,结果表明在盆地内使用"规范值"和"推荐值"时应谨慎,不然可能会对工程的抗震设防产生不利的影响。本文的"统计值"比"规范值"和"推荐值"更适用于成都平原地区,对各类工程建设的场地地震安全性评价具有一定的借鉴和参考价值。     

北京地区粉质粘土土动力学参数的统计分析

土动力学参数即土的动剪切模量比和阻尼比,对土层地震反应分析结果有重要影响。本文首先选取了北京地区2001年以来,地震安全性评价报告中20份具有完整土动力学参数的实验数据,统计分析了粉质粘土的实测土动力学参数,给出了粉质粘土在不同深度下的动剪切模量比和阻尼比平均值;然后,选取了2个典型工程场地,构建土层分析模型,进行土层地震反应分析计算,并对比分析了本文得到的统计值与典型工程场地的实测值、袁晓铭的推荐值和DB001—94规范的推荐值对土层地震反应分析计算结果的影响。分析结果表明,本文得到的统计值在北京地区具有一定的代表性和适用性,对于获得原状土样困难的场地,特别是对于较薄的夹层土,本文的统计结果在实际的地震安全性评价工作中可供参考使用。     

Simulations of water movement and solute transport through different soil texture configurations under negative‐pressure irrigation

This study examined the effects of different soil texture configurations on water movement and solute transport to provide a reliable scientific basis for the application of negative‐pressure irrigation (NPI) technology. HYDRUS‐2D was used to analyse water movement and solute transport under NPI. The main results are as follows: (a) HYDRUS‐2D can be used to simulate water movement and solute transport under NPI, as there was good agreement between the simulated and measured values for water contents, NaCl concentrations, cumulative water infiltration, and wetting distances in the horizontal and vertical directions; the Nash–Sutcliffe efficiency coefficients were in the range of 0.94–0.97. (b) Layered soils have obvious effects on water movement under NPI. With the emitter position in the loam layer, when a coarse texture of loamy sand was present below the loam layer (namely, L‐LS), irrigation water accumulated in the topsoil, and this led to an increase in evaporation compared with the homogeneous loam profile. However, fine texture silty loam or silty clay loam layers beneath the loam layer (namely, L‐SiL or L‐SiCL, respectively) was more conducive to water infiltration into the lower layer, and this increased the amount of water infiltration and simultaneously reduced the surface evaporation effectively. (c) Layered soils have obvious effects on solute transport under NPI, and salt accumulation will readily occur in the clay‐rich soil layer at the interface. The maximum soil salt accumulation of L‐LS occurred above the soil interface between the two soil layers with a value of 21.80 g/kg; however, for L‐SiCL and L‐SiL, the maximum salt accumulation occurred below the soil interface between the two soil layers, with values of 23.80 g/kg and 20.08 g/kg, respectively. (d) Interlayered soils showed remarkable changes in the water infiltration characteristics and salt‐leaching intensities under NPI, and the properties for the soil profile with a silty loam interlayer were better than those for the soil profile with a silty clay loam interlayer. The soil profile with a loamy sand interlayer had the lowest amount of water infiltration, which resulted in reductions of the salt‐leaching intensities. Thus, NPI is clearly not suitable for loamy sand soil. Overall, the results demonstrated that soil texture configurations affected water movement and solute transport under NPI. Therefore, careful consideration should be given to the use of NPI to achieve target soil water and solution conditions and reduce water loss.     

常规土类动剪切模量比和阻尼比试验研究

采用共振柱自振试验方法给出国内常规土类动剪切模量比G／Gmax和阻尼比λ变化的平均曲线,推荐值和包线,使用的共振仪是由工种力学研究所原有共振柱改装而成,并经试验验证了改装后仪器的精度可靠性,试验土类包括粘土,粉质土,粉土,砂土,淤泥和淤泥质土,土样来自国内十余个不同地区,采用折线双曲线拟合G／Gmax,λ随γ衰减关系,其中参数a和b由最小二乘法对每次试验结果回归分析得到,对同类土,将所有的a,b 值平均,用均值a和b给出动剪切模量比和阻尼比与剪应变关系,从而得到了此类土G/Gmax,λ随γ变化曲线及推荐值,试验是在两种固结压力下进行,因而得到的结构分别适用于土体埋深小于10m和埋深10m-20m之间的两种情况。     

黄土液化微细观特性试验研究

黄土液化演化过程的微观机理分析是液化防御的科学问题之一。通过微细观及动力学试验探索黄土液化的本质和影响因素。首先用CT细观扫描实验探索黄土渗透液化的细观变化,研究表明土体液面上升的根本原因是弱碱性盐类胶结物的吸水作用导致土样含水面整体上升;试样达到高饱和度,大孔隙周围颗粒间胶结物质破坏后有效应力为零,土层液化。粉土的孔隙尺寸和特殊的胶结物质导致高饱和度。土样微观结构的差异也会影响土的液面上升和破坏强度。针对低黏性粉土、粉质砂土及粉质黏土的三类黄土液化实验分析表明,低黏性粉土动荷加载时间更短,更易于液化,即低粘性粉土液化最为严重,粉质砂土为中等液化,粉质黏土相比其他黄土类别不易液化。电镜扫描土样微观结构参数分析表明,土颗粒周围胶结物质的化学元素比值(Ca/Fe),以及土颗粒粒径分布和孔隙尺寸(孔隙与颗粒比)均影响液化等级,可初步判断液化的强弱。     

Statistical Analysis of the Dynamic Parameters of Silty Clay in the Beijing Area

Soil dynamic parameters, including dynamic shear modulus ratio and damping ratio, have important effects on the results of layered soil earthquake response. In this paper, the mean parameter values of silty clay in different depths are obtained after statistical analysis of the experimental soil dynamic data from 20 recent site seismic safety evaluation reports in the Beijing area. Furthermore, based on two typical engineering sites, the influence of four different soil dynamic parameters, the statistic mean values, experimental values, values recommended by Yuan Xiaoming, and the values recommended in the code for seismic safety evaluation of engineering sites ( DB001 -94) are analyzed. The result shows that mean statistical values are applicable to seismic safety evaluation work in the Beijing area, especially for some inter-layered silty clays whose undisturbed soil samples are hard to obtain.     

等幅循环荷载作用下土的动剪模量和阻尼

本文根据我国南方8个场址81个试样的动三轴试验资料，对土在等幅循环荷载作用下，其动模量和阻尼与应变幅值的关系进行了分析研究，并与现场测试结果进行对比，分析结果，本文提出一种广义双曲线模型，能更满意地描述各类寺应力应变关系，该模型保持了形式简便，参数物理意义明确等优点，文中还分别对砂土和粘土，给出了模型中参数的统计关系式，这些表达式能明显的映粘性土和非粘性土的特性及其差别。     

SfM-MVS Photogrammetry for Splash Erosion Monitoring under Natural Rainfall

An understanding of splash erosion is the basis to describe the impact of rain characteristics on soil disturbance. In typical splash cup experiments, splashed soil is collected, filtered, and weighed. As a way to collect additional data, our experiments have been supplemented by a photogrammetric approach. A total of three soils were tested across three sites, one in the Czech Republic and two in Austria, all equipped with rain gauges and disdrometers to measure rainfall parameters. The structure from motion multiview stereo (SfM-MVS) photogrammetric method was used to measure the raindrops impact on the soil surface. The images were processed using Agisoft PhotoScan, resulting in orthophotos and digital elevation models (DEMs) with a resolution of 0.1 mm/pix. The surface statistics included the mean surface height (whose standard deviation was used as a measure of surface roughness), slope, and other parameters. These parameters were evaluated depending on soil texture and rainfall parameters. The results show a linear correlation between consolidation and splash erosion with a coefficient of determination (R²) of approximately 0.65 for all three soils. When comparing the change in soil volume with rainfall parameters, the best correlation was found with the maximum 30-minintensity (I₃₀), resulting in R² values of 0.48 (soil A, silt loam, 26% clay), 0.59 (soil B, silt loam, 18% clay), and 0.68 (soil C, loamy sand, 12% clay). The initial increase in the sample volume for the lowest splashed mass corresponds with the increase in the clay content of each of the soils. Soil A swells the most. Soil B swells less. Soil C does not swell at all and consolidates the most. We derived the relationship between the photogrammetrically measured change in surface height and the splash erosion (measured by weight) by accounting for the effect of the clay content.     

黄河三角洲粉土液化的试验研究

在野外自然地理和地质调查的基础上，以黄河地区可液化场地粉土为研究对象，利用室内动三轴和振动柱试验进行测定，分析了动荷载作用下粉土的动应力应变关系并模拟了地震荷载作用下粉土的孔压响应及抗液化强度，得出了液化破坏标准，提出了原状粉土的振动孔压上升模型。对试验结果进行分析发现，随着粘粒含量的增加，粉砂、粉土、粉质粘土、粘土达到相同剪应变所需的动剪应力也依次增加；粉土孔压比0．68、粉砂土孔压比0．87作为液化破坏开始的标志；粉土发生液化所需的循环应力比大于砂土。这些研究为以后建立适合本地区的饱和地基土地震破坏判别方法提供了参数和依据。     

武汉市区土体剪切波速与深度的经验关系

通过对武汉市区3个主要地质单元共8 305个剪切波速数据的分析整理,分别运用线性函数、一元二次多项式函数、指数函数对武汉市区不同地貌单元不同土类的剪切波速与深度的关系进行统计回归,得到其经验关系。结果表明,武汉市区土体剪切波速与埋深相关性比较明显;一元二次多项式函数的拟合效果最好。将实测数据与利用经验关系得到的预测值进行对比检验,两者基本吻合,可供武汉市区场地剪切波速数据缺乏时参考使用。     

Modelling metolachlor exports in subsurface drainage water from two structured soils under maize (eastern France)

The study investigated the processes involved in metolachlor transport in two artificially drained, structured soils in eastern France. Measured losses of bromide and metolachlor in drainage water were compared with results simulated by the mechanistic, stochastic AgriFlux model. Simulated drainage water volumes were generally similar to the measured volumes when the spatial variability of the soil water properties was taken into account. When such variability was disregarded, cumulative water volumes of the clay soil were over- or underestimated by more than 20%. Two types of adsorption were tested. For instantaneous, reversible adsorption, using the partition coefficient Koc, metolachlor losses were underestimated in the first drainage water volumes and overestimated for the total study period. The use of slow adsorption and desorption kinetics (ADK) produced an export pattern similar to the observed one. A sensitivity analysis indicated that the simulated results are very sensitive to the values of the ADK rates, especially for the silty loam soil. The effect of ADK on the attenuation of metolachlor exports was more significant than the effect of degradation (2.3 and 6.7 times higher for the clay and silty loam soils, respectively). For the same four-month period, the bromide and metolachlor losses (using ADK) in the clay soil were 2.1 and 1.3 times greater, respectively, if the macroporosity was set at 10% than if it was not simulated. Conversely, macroporosity did not significantly affect these losses in the silty loam. The main factors involved in the metolachlor transport in the studied soils were: (i) the macroporosity, especially in the clay soil because of the low hydraulic conductivity of the matrix and (ii) the sorption kinetics rates which varied according to the soil physico-chemical characteristics.     

围压对粉质粘土动力学参数影响的共振柱试验研究

土的最大动剪切模量、剪应变幅和阻尼比是对土层进行动力反应分析的重要力学参数。利用英国GDS公司生产的RCA共振柱仪,研究围压对都江堰地区粉质粘土的上述动力学参数的影响。研究表明：相同围压条件下,最大动剪切模量、剪应变幅和阻尼比随重复次数基本不变,表明该试验过程具有可重复性;最大动剪切模量、剪应变幅和阻尼比均受围压影响较大,随着围压的增大,最大动剪切模量和阻尼比均逐渐增大,而剪应变幅随着围压的增大逐渐减小。据此,建立了都江堰地区粉质粘土动力学参数随围压变化的经验公式。本研究可为土层地震动力反应分析提供参考并积累基础资料。     

黄土微观参数指标与阻尼比关联度研究

对岷县地震台、庆阳黄土塬2~12m深度土层的粉土、粉质黏土样品,利用室内动三轴试验和扫描电镜试验,测定阻尼比和微观结构特征,研究了粉土、粉质黏土的阻尼比随深度的变化及应力应变关系,采用灰色关联度方法,分析了黄土竖向（沉积方向）和横向（垂直于沉积方向）的微观结构参数对阻尼比影响的主次关系及其权重。研究结果表明:小应变下,粉土和粉质黏土阻尼比随着深度的增加而减小;粉土和粉质黏土的微观参数与阻尼比有一定的关联性,粉土竖向的微观参数对阻尼比的影响较为敏感;粉质黏土横向的微观参数对阻尼比的影响更加敏感;影响权重方面,粉质黏土的平均形状系数影响权重最大,对阻尼比的影响最大;粉土的平均形状系数、分形维数和概率熵影响权重最大,对阻尼比影响最敏感。平均面积无论在关联度还是影响权重方面对阻尼比影响最小,该结论粉土与粉质黏土保持一致。     

饱和粉土液化特性的大型振动台模型试验研究

京沪高速铁路徐沪段路基的粉土粘粒含量少于1.5%、粉粒含量约为80%,在强烈地震作用下存在着液化可能性.为充分研究这一饱和粉土地层的液化特性,本文作者利用大型地震模拟振动台,进行了模拟自由场地饱和粉土的地震液化模型试验,试验结果再现了自然地震触发的粉土液化的各种宏观震害现象,揭示了饱和粉土的地震液化规律和特征。试验结果为京沪高速铁路徐沪段路基的抗震设计提供了参考依据。     

渤海海域粉质粘土动力学参数的统计分析

本文整理了26个渤海海域场地土动力学测试报告,并按埋深分段统计了0至115m深度范围内粉质粘土的动力学参数,即动剪切模量比和阻尼比。然后,将本文统计值与袁晓铭推荐值和施春花统计过的北京地区粉质粘土的动力学参数值进行了比较,发现海域场地土与陆地场地土的动力学参数值存在较大差异。之后,选择渤海海域的两个场地,建立了相应的土动力学模型,分别选取实测值、本文统计值、施春花统计值进行场地地震反应分析,发现本文统计值与实测值的结果符合的较好。在渤海海域场地地震反应分析工作中,某些粉质粘土层难以获得动力学参数时,可以参考本文的统计值。