波浪在Jarlan型开孔潜堤上的运动

The wave motion over a submerged Jarlan-type breakwater consisting of a perforated front wall and a solid rear wall was investigated analytically and experimentally. An analytical solution was developed using matched eigenfunction expansions. The analytical solution was confirmed by previously known solutions for single and double submerged solid vertical plates, a multidomain boundary element method solution, and experimental data. The calculated results by the analytical solution showed that compared with double submerged vertical plates, the submerged Jarlan-type perforated breakwater had better wave-absorbing performance and lower wave forces. For engineering designs, the optimum values of the front wall porosity, relative submerged depth of the breakwater, and relative chamber width between front and rear walls were 0.1–0.2, 0.1–0.2, and 0.3–0.4, respectively. Interchanging the perforated front wall and solid rear wall may have no effect on the transmission coefficient. However, the present breakwater with a seaside perforated wall had a lower reflection coefficient.     

Wave interaction with a perforated wall breakwater with a submerged horizontal porous plate

This study examines the hydrodynamic performance of a new perforated-wall breakwater. The breakwater consists of a perforated front wall, a solid back wall and a submerged horizontal porous plate installed between them. The horizontal porous plate enhances the stability and wave-absorbing capacity of the structure. An analytical solution based on linear potential theory is developed for the interaction of water waves with the new proposed breakwater. According to the division of the structure, the whole fluid domain is divided into three sub-domains, and the velocity potential in each domain is obtained using the matched eigenfunction method. Then the reflection coefficient and the wave forces and moments on the perforated front wall and the submerged horizontal porous plate are calculated. The numerical results obtained for limiting cases are exactly the same as previous predictions for a perforated-wall breakwater with a submerged horizontal solid plate [Yip, T.L., Chwang, A.T., 2000. Perforated wall breakwater with internal horiontal plate. Journal of Engineering Mechanics ASCE 126 (5), 533–538] and a vertical wall with a submerged horizontal porous plate [Wu, J.H., Wan, Z.P., Fang, Y., 1998. Wave reflection by a vertical wall with a horizontal submerged porous plate. Ocean Engineering 25 (9), 767–779]. Numerical results show that with suitable geometric porosity of the front wall and horizontal plate, the reflection coefficient will be always rather small if the relative wave absorbing chamber width (distance between the front and back walls versus incident wavelength) exceeds a certain small value. In addition, the wave force and moment on the horizontal plate decrease significantly with the increase of the plate porosity.     

Extreme wave run-up and pressure on a vertical seawall

The performance of coastal vertical seawalls in extreme weather events is studied numerically, aiming to provide guidance in designing and reassessing coastal structures with vertical wall. The extreme wave run-up and the pressure on the vertical seawall are investigated extensively. A time-domain higher-order boundary element method (HOBEM) is coupled with a mixed Eulerian-Lagrangian technique as a time marching technique. Focused wave groups are generated by a piston wave-maker in the numerical wave tank using a wave focusing technique for accurately reproducing extreme sea states. An acceleration-potential scheme is used to calculate the transient wave loads. Comparisons with experimental data show that the extended numerical model is able to accurately predict extreme wave run-ups and pressures on a vertical seawall. The effects of the wave spectrum bandwidth, the wall position and the wave nonlinearity on the wave run-up and the maximum wave load on the vertical seawall are investigated by doing parametric studies.     

A Note on Tsunami Bore Front

A note is presented on tsunami bore front. This tsunami bore front is an old dynamical problem but also a new problem to be understood. The tsunami event on 2004 December 26 has raised this is an urgent problem. The author introduces here a model in order to see a hydrodynamical specific property of the tsunami bore front. This modeling gives us a new understanding about what mechanics is for the interested tsunami bore front, especially, around a coastal zone. This work adds a new understanding about mechanics of water motions as the tsunamis generated by the earthquake undersea at a distant area from the coast. The model in this work points out a specific transitional pattern as a function of time and space of tsunami bore front. This modeling gives what is essential at considering tsunami bore front.     

A Note on Tsunami Bore Front

A note is presented on tsunami bore front. This tsunami bore front is an old dynamical problem but also a new problem to be understood. The tsunami event on 2004 December 26 has raised this is an urgent problem. The author introduces here a model in order to see a hydrodynamical specific property of the tsunami bore front. This modeling gives us a new understanding about what mechanics is for the interested tsunami bore front, especially, around a coastal zone. This work adds a new understanding about mechanics of water motions as the tsunamis generated by the earthquake undersea at a distant area from the coast. The model in this work points out a specific transitional pattern as a function of time and space of tsunami bore front. This modeling gives what is essential at considering tsunami bore front.     

Analytical and Experimental Studies on Hydrodynamic Performance of Semi-Immersed Jarlan-Type Perforated Breakwaters

The present study proposes a new semi-immersed Jarlan-type perforated breakwater including a perforated front wall, a solid rear wall, and a horizontal perforated plate connecting the lower tips of the two walls. An analytical solution is developed to estimate the hydrodynamic performance of the new breakwater. The analytical solution is confirmed by solutions for special cases, an independently developed multi-domain boundary element method solution and experimental data. Numerical examples based on the analytical solution indicate that compared with previous semi-immersed breakwaters, the new breakwater may have better wave-absorbing performance and smaller wave forces. Some useful results are presented for practical designs of semi-immersed Jarlan-type perforated breakwaters.     

Wave impacts on structures with rectangular geometries: Part 1. Seawalls

This paper considers steep wave impact on seawalls of various geometries. A simple analytical model for the pressure impulse due to a wave of idealized geometry and dynamics is developed and applied to the following geometries: (a) vertical seawall with a berm, (b) vertical seawall with a ditch at its base and (c) vertical seawall with a block missing (damaged condition).The method uses eigenfunction expansions in each of the rectangular regions that satisfy some of the rigid surface conditions and a simplified free-surface condition. Their unknown coefficients are determined from the impact boundary condition, rigid wall conditions and by matching the values and the horizontal derivatives of the solutions in each rectangular region at their mutual boundary. The method yields the pressure impulse throughout the entire region. The overall impulse and moment impulse on the seawall and a simple model for the uprush of the spray jet after the impact are also presented. The effects of different impact regions and different geometries can therefore be quickly estimated and used to show trends in the results. It is shown that berms generally have a beneficial effect on reducing the impulse, moment impulse and uprush, but not the maximum pressure impulse on the seawall, whereas ditches are generally and sometimes strongly detrimental for all effects except uprush. A missing block in the seawall gives an almost constant or linearly decreasing value inside the gap (depending on the boundary condition applied at the rear of the gap being hard or soft respectively); the soft case can affect the pressure impulse on the front face of the seawall, thereby affecting the impulse and moment impulse.     

Wave-porous structure interaction modelling using Improved Meshless Local Petrov Galerkin method

This paper presents the application of the Improved Meshless Local Petrov Galerkin method with Rankine source (Sriram and Ma, 2012) Sriram and Ma (2012) for wave interaction with porous structure model. The mathematical model is based on a unified governing equation that incorporates both pure fluid and porous region. The porous flow model is based on the empirical resistance coefficients. The interface between the pure fluid and porous region is numerically treated using background nodes having the porosity information and interpolated over the particle using simplified finite difference interpolation method. The model is validated using the available experimental results for wave damping over the permeable bed. The developed model is used to analyse the different shape of the seawall such as flaring shaped seawall, recurve wall and vertical wall. Then the validated model is used for analysing the overtopping amount due to the effect of porous layer in-front of the different sea wall profile. Numerical expression for overtopping amount has been provided for the different configurations from the numerical model.     

Experimental investigating on the reflected waves from the caisson-type vertical porous seawalls

The hydrodynamic efficiencies of caisson-type vertical porous seawalls used for protecting coastal areas were calculated in this study. Physical models were developed to compare the wave reflection from vertical plane, semi-porous, and porous seawalls caused by both regular and random waves. Tests were carried out for a wide range of wave heights, wave periods, and different water depths (d=0.165, 0.270 and 0.375 m). The performance regarding the reflected waves from porous and semi-porous seawalls showed improvement when compared with those from the plane seawall. The reflection coefficients of the porous and semi-porous seawalls were calculated as 0.6 and 0.75, respectively, while the coefficient for the fully reflecting plane vertical wall was significantly higher (0.9). It was also observed that the reflection coefficient decreases with increase in wave steepness and relative water depth. In addition, the reduction in the reflection coefficient of porous and semi-porous seawalls, as compared to that of a plane seawall, was observed for both regular and random waves. New equations were also proposed to calculate the reflection coefficient of different types of seawalls with the aid of laboratory experiments. By verifying the developed equations using some other experimental data, it was validated that the equations could be used for practical situations. The results of the present study can be applied to optimize the design of vertical seawalls and for coastal protecting schemes.     

开孔墙对减小波浪载荷效果的CFD分析

极限波浪载荷是导致海上结构物疲劳失效的主要载荷之一。固定在海洋基础结构物上的直立开孔墙对减小波浪载荷具有一定的效果。基于不可压缩黏性流体流动理论和N-S方程,采用VOF与Level-set相结合追踪自由表面的方法,首先建立数值波浪水槽,然后对开孔墙本身的开孔率和开孔墙与直立墙之间的相对距离,在降低反射系数和波浪力两个方面进行分析。研究结果表明,开孔墙可以明显降低作用在结构物上的波浪力,开孔墙本身的开孔率和与直立墙的相对距离会对其产生明显影响;不同波浪参数下会存在一个最佳的开孔率,但是不同波浪参数时最佳开孔率会略有不同;当开孔墙和直立墙的相对距离在0.2到0.3之间时,开孔墙的消波减载效果最佳。研究结果可为海洋工程相关设计提供一定的参考。     

非淹没刚性植物对海啸作用下海堤水动力特性影响数值模拟研究

基于非静压单相流模型NHWAVE建立了高精度数值波浪水槽。通过设计不同的计算工况,系统研究了非淹没刚性植物对海啸作用下海堤周围水动力特性的影响。着重分析了不同入射波高、不同植物分布密度以及不同植物分布宽度条件下海啸波沿程波形特征以及海堤堤顶越浪流空间分布特征。结果表明:不同入射波高、植物分布密度以及植物宽度条件下,堤顶流厚度和水体流速具有明显单调的变化趋势,并且随着植物分布密度和宽度增大,波能衰减增大;随着入射波非线性增强,植物分布密度和分布宽度对堤顶前段水流厚度的影响也随之增强,而对堤顶后段水流厚度的影响则减弱,且堤顶后缘水流厚度约为堤顶前缘厚度的二分之一;在波浪非线性较大情况下,植物的存在对堤顶流速度的空间分布趋势几乎没有影响,但相对堤顶流速度增加程度均大于无植物情况,且堤顶后缘水流速度约为堤顶前缘的1.6倍。     

Hydroelastic Response of VLFS with An Attached Submerged Horizontal Solid/Porous Plate Under Wave Action

The hydroelastic responses of a submerged horizontal solid/porous plate attached at the front of a very large rectangular floating structure(VLFS) under wave action has been investigated in the context of linear water wave theory. Darcy's law is adopted to represent energy dissipation in pores. It is assumed that the porous plates are made of material with very fine pores so that the normal velocity across the perforated porous is linearly associated with the pressure drop. In the analytic method, the eigenfunction expansion-matching method(EEMM) for multiple domains is applied to solve the hydrodynamic problem and the elastic equation of motion is solved by the modal expansion method. The performance of the proposed submerged horizontal solid/porous plate can be significantly enhanced by selecting optimal design parameters, such as plate length, horizontal position, submerged depth and porosity. It is concluded that good damping effect can be achieved through installation of solid and porous plate.Porous plate has better damping effect at low frequencies, while solid plate has better damping effect at high frequencies. The optimal ratio of plate length to water depth is 0.25-0.375, and the optimal ratio of submerged depth to water depth is 0.09-0.181.     

A coupled numerical model for simulation of wave breaking and hydraulic performances of a composite seawall

A numerical model is developed by combining a porous flow model and a two-phase flow model to simulate wave transformation in porous structure and hydraulic performances of a composite type low-crest seawall. The structure consists of a wide submerged reef, a porous terrace at the top and an impermeable rear wall. The porous flow model is based on the extended Navier-Stokes equations for wave motion in porous media and k−ε turbulence equations. The two-phase flow model combines the water domain with the air zone of finite thickness above water surface. A unique solution domain is established by satisfying kinematic boundary condition at the interface of air and water. The free surface advection of water wave is modeled by the volume of fluid method with newly developed fluid advection algorithm. Comparison of computed and measured wave properties shows reasonably good agreement. The influence of terrace width and structure porosity is investigated based on numerical results. It is concluded that there exist optimum value of terrace width and porosity that can maximize hydraulic performances. The velocity distributions inside and in front of the structure are also investigated.     

Wave impacts on structures with rectangular geometries: Part 2 decks,baffles and seawalls with impermeable or porous surfaces

This paper considers wave impacts on baffles, on baffles or decks adjacent to a vertical wall, and on porous seawalls and/or sea beds. For seawalls and vertical baffles, impacts can occur in steep waves, whilst a deck can be struck from below by a rising wave crest either in open sea or in a tank with standing waves (sloshing). A simple analytical model for the pressure impulse, P, due to a wave of idealized geometry and dynamics is developed and applied to the following geometries with impermeable surfaces:

• •horizontal wave impact onto a vertical wall with a deck at the waterline,
• •vertical wave impact under a deck in the same configuration (equivalent to vertical water impact of a horizontal plate),
• •horizontal wave impact onto a surface-piercing vertical baffle in open sea,
• •as for 3. but with the baffle in front of a wall,
• •as for 4. but with a deck extending from the vertical wall to the baffle,
• •bottom-mounted baffle in front of a wall with impact occurring on the wall.

We also consider cases that complement part 1 of this paper to include the effect on impacts on a seawall with a porous sea bed and/or sea wall with/without a berm. Finally we reconsider case 3) above but with a porous baffle.The method uses eigenfunction expansions in each of the rectangular regions that satisfy some of the impermeable or porous surface conditions, and a simplified free-surface condition. Their unknown coefficients are determined from the impact boundary condition, impermeable or porous boundary conditions and by matching the solutions, in any two neighbouring rectangles, along their common boundary. Although the fluid motion is treated rather crudely, the method yields the pressure impulse throughout the entire region. Impulses, I, and moment impulses, M, on all or parts of the structure are also presented.     

双消浪室局部开孔沉箱防波堤反射特性的理论与试验研究

双消浪室局部开孔沉箱防波堤具有低反射、结构受力小、适宜较大水深和工程造价低等优点。为明确双消浪室局部开孔沉箱水动力特性的主要影响因素,采用理论分析和物理模型试验相结合的方法,对规则波和不规则波作用下双消浪室局部开孔沉箱防波堤的反射特性进行研究。基于势流理论,建立规则波和不规则波对局部开孔沉箱防波堤作用的三维解析解,采用二次压力损失边界条件考虑沉箱开孔墙对波浪运动的影响,利用周期性边界条件考虑防波堤结构沿长度方向的周期性变化。开展相应规则波和不规则波物理模型试验,验证理论模型的合理性。通过算例分析,研究不同波浪要素和结构参数对防波堤反射特性的影响。研究表明:双消浪室局部开孔沉箱相对消浪室宽度取值为0.08~0.20,沉箱前墙开孔率大于后墙开孔率时,防波堤在较大波浪频率范围内消波效果显著;当前后墙的开孔率相等时,防波堤反射系数的最小值随着开孔率增大而减小。     

基于SPH方法的开孔沉箱比尺效应研究

由于在前壁上设置了尺寸较小的孔,开孔沉箱受流体黏性力作用显著,依照弗劳德数相似准则设计模型存在比尺效应。为揭示比尺效应,建立了模拟波浪与开孔沉箱相互作用的光滑粒子流体动力学(SPH)模型。其中流体运动由连续性方程和Navier-Stokes方程控制,固壁边界由改进的动力边界粒子施加。模型收敛性通过分析不同粒子分辨率下的波浪反射系数得到,模型精度通过比较计算与理论波浪反射系数证明。使用经过验证的SPH模型,计算并比较了不同几何比尺和开孔率下开孔沉箱附近的涡量场、箱体外侧的波面时程曲线和波浪反射系数。结果表明,随着模型几何比尺的减小,开孔沉箱受到偏大的流体黏性力,致使更多波能在湍流运动中耗散,进而减小了波浪反射系数并降低了箱体外侧的波面高度。     

Wave reflection from vertical breakwater with porous structure

This paper presents numerical solutions for the wave reflection from submerged porous structures in front of the impermeable vertical breakwater. A new time-dependent mild-slope equation involves the parameters of the porous medium including the porosity, the friction factor and the inertia coefficient, etc. is derived for solving the boundary value problem. A comprehensive comparison between the present model and the existing analytical solution for the case of simple rectangular geometries of the submerged structure is performed first. Then, more complicated cases such as the inclined and trapezoidal submerged porous structures in front of the vertical breakwater with sloping bottom are considered. This study also examines the effects of the permeable properties and the geometric configurations of the porous structure to the wave reflection. It is found that the submerged porous structure with trapezoidal shape has more efficiency to reduce the wave reflection than that of triangular shape. The numerical results show that the minimum wave reflection is occurred when the breakwater is located at the intermediate water depth.     

An investigation of breaking wave pressures on inclined walls

Shoreline structures are subjected to breaking wave loads which may reach 690 KN/m². One possibility to reduce these loadings is to slope the exposed surface backwards. The possible amount of reduction in breaking wave loads is, however, unclear, and recent model tests indicated that sloped walls might be exposed to higher loads than are vertical walls. Within the Wave Energy Group at Queen's University Belfast, tests on a 1/36 model of a shoreline wave power station were conducted in order to assess the influence of front wall inclination on the magnitude of breaking wave pressures. It was found that breaking wave pressures decrease from 100% for the vertical wall to 44% for a 32.7° backwards inclined wall and to 64% for a 32.7° forward inclined wall. From the results it was concluded that a maximum pressure of 105% can be expected for a 10° forward inclined wall. Design recommendations were found to be conservative.     

强潮河口桥墩涌潮压力试验研究

为明确强潮河口设计条件下涌潮压力特征,以嘉绍大桥工程为背景进行了涌潮压力的动态测试和分析。选取主墩围堰和施工栈桥进行现场观测,分析了涌潮压力分布及其变化的特点。利用经验模态分解法,研究了涌潮压力的时均和脉动特性,建立了涌潮压力及其脉动分量极值与涌潮高度的拟合关系。研究结果表明:涌潮压力变化脉动性强,经验模态分解法能较好地处理这种非平稳时变信号;时均分量反映了局部水位的平均变化趋势,脉动分量反映了涌潮与结构物相互作用时自由水面的紊动情况;从垂向分布上看,压力极值在潮前低水位附近最大,并随着传感器安装高程的增加而减小;从平面分布上看,主墩围堰的迎潮面压力极值最大,背潮面最小;涌潮压力及其脉动分量的极值与涌潮高度满足指数分布规律。     

开孔沉箱在斜向入射波作用下受力研究

应用透空壁内流体速度与壁两侧的压力差成正比的线性模型,研究了斜向波与无限多个开孔沉箱的相互作用.依照结构物的几何形状,把整个流域分成无限多个子域,在每个子域内应用特征函数展开法对速度势进行展开.对于沉箱内的波浪运动,引入相位差概念;在构造反射波模型时,考虑了结构物的几何形状影响.列举出物理模型实验结果与数值实验结果的比较,可以看出两者吻合较好.进一步的数值计算验证表明,当孔隙系数无限大时,开孔墙前后的速度非常接近.在低频入射波作用下,垂直于沉箱的水平力随角度的变大而减小,平行于沉箱排列方向的力则变大.