组合桶形基础水平循环承载力模型试验

在一个大型土池中进行了软土中组合四桶基础在竖向静荷载与水平循环荷载共同作用下的承载力模型试验,研究了竖向静荷载与水平循环荷载对组合桶形基础破坏形式与承载力的影响。试验结果表明,组合四桶基础的变形主要包括水平循环变形与竖向循环累积沉降。基础的破坏形式取决于水平循环荷载与竖向静荷载。若竖向静荷载较小,过大的水平循环位移将导致基础破坏;随竖向静荷载增加,竖向循环累积沉降将变为导致基础破坏的主要原因。试验结果还表明,在不同竖向静荷载与水平循环荷载共同作用下,基础的水平循环承载力大约为水平静承载力的70%左右。     

Pullout capacity of embedded suction anchors in sand

An analytical solution has been developed to estimate the horizontal, vertical, and inclined loading pullout capacities of embedded suction anchors in sand. Validation of the analytical solution on pullout capacities has been made through comparisons with the centrifuge model test results. Primary variables for the centrifuge model tests are the depth to the loading point, the load inclination angle, and the addition of flanges. The results indicate that both the horizontal and vertical pullout capacities of the embedded suction anchor in sand increase, reach the peak and then start to decrease as the loading point moves downward. The inclined loading pullout capacity is very much dependent on the load inclination angle and the loading point. The effect of flanges on the pullout capacities is also found to be significant.     

Assessment of cyclic response to suction caisson in clay using a three-dimensional displacement approach

An investigation was made to present analytical solutions of cyclic response to suction caisson subjected to inclined cyclic loadings in clay using a three-dimensional displacement approach. A model representing the relationship between vertical load and vertical displacement and that between lateral load and lateral displacement along the skirt of suction caisson subjected to cyclic loadings is proposed for overconsolidated clay. For the effect of vertical load on cyclic load capacity of suction caisson, using the Mindlin solution in the case of a vertical point load, the vertical stress of soil under the base of suction caisson is presented. For the stress state of soil beneath the base of suction caisson subjected to cyclic loading, the Mohr–Coulomb failure line and critical state line are presented and the relationship between total stress, effective mean principal stress, stress difference, and pore-pressure is elucidated. The comparison of results predicted by the present method for a suction caisson subjected to cyclic loadings in clay has shown good agreement with those obtained from field tests. Cyclic behavior of clay up to failure is made clear from the relationship between cyclic tensile load, vertical and lateral displacements, and rotation and that between depth, vertical, and lateral pressures.     

海上风机吸力基础的水平受荷研究综述

吸力基础具有施工速度快、安装过程中受海况天气影响小且易于回收重复利用等优点,被广泛应用于海洋工程。当吸力基础作为海上风电塔架的基础时,常常承受较大的水平荷载,因此其水平承载力是设计的主控因素。介绍了海上风机基础的设计要求,分析了影响基础水平承载性状的因素,总结了吸力基础受水平单调荷载、水平循环荷载和不同荷载组合三个方面的研究现状。讨论了水平荷载的大小、水平加载的高度(偏心率)、循环荷载的频率、循环荷载的次数、循环荷载的幅值、循环荷载的方向性、竖向荷载对吸力基础水平承载性状的影响,考虑了水平荷载的非共线性,指出了目前研究的不足,明确了吸力基础水平承载性状进一步研究的方向,提出了供工程实践参考的建议。     

Simplified limit solutions for the capacity of suction anchors under undrained conditions

Upper bound plastic limit analyses (PLA) can provide a useful framework for estimating the load capacity of suction caisson anchors in purely cohesive soils. Since arbitrary assumptions regarding the soil stress state are not required in the PLA formulation, it may be used with greater consistency compared to other simplified approaches such as limit equilibrium methods. While PLA methods do not attempt to include all of the complexities of anchor behavior, they can provide a relatively simple framework for visualizing anchor kinematics leading to an understanding of the relative importance of various parameters on suction anchor load capacity. The most rigorous PLA formulations involve postulating a three-dimensional anchor-soil failure mechanism and deriving expressions for internal energy dissipation throughout the mechanism. This approach can involve extensive numerical integrations and a relatively complex scheme for optimizing the failure mechanism to obtain a least upper bound collapse load. Considerable simplification is possible if the problem is formulated in terms of ultimate unit resistances (lateral, axial, and their interaction) that can be exerted by the soil on the caisson. In this case, the caisson failure mechanism can be characterized in terms of one or two optimization variables. Simple expressions for the ultimate unit resistances acting on the caisson can be obtained from several sources including rigorous PLA solutions, finite element techniques, or experimental measurements. General expressions are possible by limiting consideration to common, idealized strength profiles such as uniform or constant gradient. Such simplified formulations are particularly valuable for providing an analysis tool accessible to practicing engineers. Suction caisson anchors can be subjected to a variety of load orientations including nearly vertical uplift forces imposed by the vertical tendons of tension leg platforms, horizontal loads imposed by catenary mooring systems, and inclined loads imposed by taut moorings. Recently, PLA methods have been applied to the analysis of suction caissons subjected to this range of loading conditions. This paper reviews the formulation of these analyses and summarizes the most significant findings.     

复合加载下桶形基础循环承载性能数值分析

作为一种新型基础形式,吸力式桶形基础除了承受海洋平台结构及自身重量等竖向荷载的长期作用之外,往往还遭受波浪等所产生的水平荷载及其力矩等其它荷载分量的瞬时或循环作用。对复合加载模式下软土地基中桶形基础及其结构的循环承载性能尚缺乏合理的分析与计算方法。应用Andersen等对重力式平台基础及地基所建议的分析方法,基于软黏土的循环强度概念,在大型通用有限元分析软件ABAQUS平台上,通过二次开发,将软土的循环强度与Mises屈服准则结合,针对吸力式桶形基础,基于拟静力分析建立了复合加载模式下循环承载性能的计算模型,并与复合加载作用下极限承载性能进行了对比。由此表明,与极限承载力相比,桶形基础的循环承载力显著降低。     

Evaluation of pullout load capacity of suction caissons in sand using a three-dimensional displacement approach

An investigation was conducted to obtain analytical solutions for the pullout behavior of a suction caisson undergoing inclined loads in sand. The inclined load is transformed into an equivalent load system in which the vertical, horizontal, and moment loads are applied on the center of the lid of the suction caisson. The vertical and lateral stiffness coefficients along the skirt of the suction caisson in sands are presented using the new three-dimensional elastic solutions taking into account the nonhomogeneous and nonlinear properties of the sand. The vertical, lateral, and rocking stiffness coefficients on the base of the suction caisson are presented considering the solutions of a hollow rigid cylindrical punch acting on the surface of a soil. The yield, pullout, and failure for sands with the nonhomogeneous and nonlinear characteristics are taken into consideration. The effects of the load inclination, the loading depth, and the aspect ratio on the pullout load capacity of the suction caisson are presented. Behaviour of the suction caisson in sand prior to failure is clarified from the relationship between tensile load, displacement, and rotation and that between depth, vertical pressure, and lateral pressure.     

Bearing capacity of offshore umbrella suction anchor foundation in silty soil under varying loading modes

Considering the current disadvantages of present offshore wind turbine foundations, a novel anchor foundation with skirt and branches is proposed, called offshore umbrella suction anchor foundation (USAF). A series of experiments and numerical simulations were performed to explore the bearing capacity of the USAF under various kinds of loading modes. The bearing characteristics and the anchor–soil interactions are described in detail for horizontal static loading, horizontal cyclic loading, and an antidrawing (pullout) test in silty soil. In the static loading test, the load–deflection of the anchor under step loading was analyzed and the normalized curve of the load–deflection was obtained to determine the ultimate horizontal bearing capacity of the anchor under normal working conditions. Under horizontal cyclic loading, the relationship between the plastic cumulative deformation and cyclic number was determined. In addition, the responses of USAF were investigated for a low wave frequency and storm surges. In the drawing test, it was found that a “segmentation phenomenon” occurred during the test. Moreover, a method to identify the maximum antidrawing load of USAF was provided based on dynamic mechanics. The numerical results show that the use of anchor branches and skirt can enhance the bearing performance of USAF to a certain degree. However, the anchor branch has a slight positive influence on the bearing performance improvement. The USAF is not only similar to a stiff short pile, but a rotation occurs. The failure envelope under composite loading (V-M) was obtained and the changes associated with changes in the aspect ratio of the internal compartment were clarified.     

Analysis of pullout load capacity of suction caissons in clay by a three-dimensional displacement approach

A study was made to present analytical solutions of pullout load capacity for a suction caisson subjected to inclined tension in clay. The inclined tension on the skirt of the suction caisson is transformed into an equivalent system comprised of the vertical, horizontal, and moment load applied on the center of the lid. The vertical and horizontal stiffness coefficients along the skirt of the suction caisson in clay are presented by three-dimensional elastic solutions considering the nonhomogeneous and nonlinear property of clay. The vertical, horizontal, and rocking stiffness coefficient of the suction caisson on the base are presented considering the solutions of a hollow rigid cylindrical punch acting on the surface of clay. The envelopes of the horizontal and vertical ultimate load capacity for clay are presented. The yield, pullout, and failure for clay are taken into consideration. The effects of load inclination, loading depth, and aspect ratio on the pullout load capacity are shown. Behavior of the suction caisson in clay up to failure is investigated using the relationship between tensile load and displacement and that between depth, vertical, and horizontal pressure.     

Lateral Bearing Capacity of Modified Suction Caissons Determined by Using the Limit Equilibrium Method

The modified suction caisson (MSC) adds a short-skirted structure around the regular suction caissons to increase the lateral bearing capacity and limit the deflection. The MSC is suitable for acting as the offshore wind turbine foundation subjected to larger lateral loads compared with the imposed vertical loads. Determination of the lateral bearing capacity is a key issue for the MSC design. The formula estimating the lateral bearing capacity of the MSC was proposed in terms of the limit equilibrium method and was verified by the test results. Parametric studies on the lateral bearing capacity were also carried out. It was found that the lateral bearing capacity of the MSC increases with the increasing length and radius of the external skirt, and the lateral bearing capacity increases linearly with the increasing coefficient of subgrade reaction. The maximum lateral bearing capacity of the MSC is attained when the ratio of the radii of the internal compartment to the external skirt equals 0.82 and the ratio of the lengths of the external skirt to the internal compartment equals 0.48, provided that the steel usage of the MSC is kept constant.     

Pullout behavior of suction anchors in soft marine clays

In the field of ocean engineering, a beginning has been made in the use of large‐sized suction anchors for safe anchoring of large compliant structures. Suction anchors derive most of their uplift resistance from passive suction developed during the pullout movement. This article describes a set of laboratory tests on model suction anchors of three different embedment ratios to estimate the pullout behavior of suction anchors in soft clays typical of Indian marine clays. Tests were conducted on model anchors installed in soil beds prepared at four different consistencies in a test tank. This study shows the influence of soil consistency and embedment ratio (L/D) on the pullout behavior of suction anchors and on the variation of suction pressure at the top of the soil plug. The test results reveal that the behavior of suction anchors is much better than the behavior of open‐ended anchors from the considerations of both capacity and deformation. The consistent development of suction inside the anchor top confirms the plug formation and significant breakout resistance in the form of suction‐induced reversed end bearing. The results are further analyzed in terms of suction breakout factors. Further, the effect of burial depth of suction anchor on pullout behavior is shown.     

A method analyzing deformation of anchor foundations in soft clay under static and cyclic loads

The paper presents a constitutive model to describe undrained cyclic stress-strain responses of soft clays based on the equivalent visco-elastic and creep theories. The hysteretic and nonlinear stress-strain responses of soft clays are described using the equivalent visco-elastic relationship and variations of the cyclic modulus and the damping ratio with the octahedral shear strain, respectively in the model. The cyclic accumulative strain is described using the Mises creeping potential function and the associated flow rule. The method determining the model parameters is given by static and cyclic triaxial tests. The finite element method to analyze deformation of anchor foundation in soft clay under static and cyclic loads is developed based on the model. For the method, a cyclic loading time history is divided into a series of incremental loading sub-processes which include one load cycle at least. The cyclic stress-strain responses of soil elements at any time are not tracked in detail and determined by the equivalent visco-elastic calculations for every loading sub-process. The accumulative deformation of anchor foundations is calculated using the initial strain algorithm. The method has been implemented in ABAQUS Software by developing interface programs. Model tests of the suction anchors are conducted and predicted using the method. Comparisons of predicted and model test results show that the method can be used to evaluate cyclic stability and reveal the failure process and mechanism of anchor foundations by analyzing deformation time-histories.     

Model tests on installation and extraction of suction caissons in dense sand

A series of model tests were performed on steel- and Perspex-made suction caissons in saturated dense marine sand to explore installation and extraction behaviors. The extractions of the caisson were conducted by applying monotonic loading or by pumping water into the caisson. Responses of suction caissons to pullout rates, aspect ratios, and extraction manners were examined. Test results show that a cone-shaped subsidence region occurs around the suction caisson during the suction-assisted installation. The pullout bearing capacity of the suction caisson in sand is dominated by the loading rate and the loading manner. For the suction caisson subjected to monotonic loading, the maximum bearing capacity is reached at the pullout rate of about 20.0?mm/s. The mobilized vertical displacement corresponding to the pullout capacity increases with increasing the pullout rate. The passive suction beneath the suction caisson lid reaches the maximum value when the pullout bearing capacity is mobilized. In addition, during the suction caisson extracted by pumping water into the caisson, the maximum pore water pressure in the caisson is obtained under the displacement of approximately 0.04 times the caisson diameter. The absolute values of the maximum pore water pressures for the suction caissons approximately equal those of the maximum vertical resistances at the monotonic pullout rate of 5 mm/s. When the vertical displacements of the suction caissons with the aspect ratio of 1.0 and 2.0 reach 0.92 and 1.77 times the caisson diameter, respectively, the seepage failure occurs around the caissons. Using a scaling method, the test results can be used to predict the time length required for the prototype suction caisson to be extracted from the seabed.     

Failure Loci of Suction Caisson Foundations Under CombinedLoading Conditions

Suction caissons are widely used to support offshore fixed platforms in coastal areas. The loadings transferred to suction caissons include the eccentric lateral force induced by waves and self weight of the platform structure. However, under this kind of combined loading conditions, the failure mechanism of caissons with shallow embedment depths is quite different from conventional deep foundations or onshore shallow footings. The behaviour of caissons subjected to combined loadings may be described with the "failure locus" in force resultant spaces. Here the failure loci of smooth caissons are studied by use of finite element approach, with the embedment ratio of caissons varying in the range of 0.25～1.0 and eccentricity ratio of horizontal loadings in 0～10. The platform settlement and tilt limits are involved into determination of failure loci, thus the platforms can avoid significant displacements for the combined loadings located inside the failure locus. Three families of loading paths are used to map out the locus. It is found that the shape of failure loci depends on 3 non-dimensional parameters, and the failure locus of a given caisson changes gradually from the elliptical curve to hooked curve with increasing shear strength of soil. The lateral capacity of short caissons may be enhanced by vertical forces, compared with the maximum lateral capacity of long caissons occurring at the vertical force being zero. The critical embedment ratios partitioning elliptical and hooked loci are proposed.     

Characteristic Test Study on Bearing Capacity of Suction Caisson Foundation Under Vertical Load

Suction caisson foundations are often subjected to vertical uplift loads, but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion. In order to study the uplift bearing mechanism and failure mode of suction caisson foundation, a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode. Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity. The smaller the permeability coefficient is, the higher the residual negative pressure will be. And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson. When the load reaches the ultimate bearing capacity, both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay. Combined the uplift bearing characteristics of caisson in sandy soil and soft clay, the bearing capacity composition and the calculation method are proposed. It can provide a reference for the engineering design of suction caisson foundation under vertical load.     

离岸裙式吸力基础在砂土地基中沉贯性研究

吸力基础是海洋工程中新型的一种基础型式,广泛应用于海洋平台、海洋浮动式结构等,近年来,也被作为浅海离岸风力发电工程的基础。吸力基础易遭受较大的水平动力荷载和弯矩,从而可能产生较大水平位移和转角;同时,由于海床冲刷,会降低其承载能力。为克服这些不足,提出了一种新型吸力基础———裙式吸力基础,把分析传统吸力基础砂土中的沉贯方法,拓广到裙式吸力基础中,研究该基础型式在砂土中的可沉贯性以及所需的吸力;并与同情况下的传统吸力基础进行了比较,证明了所提出的裙式吸力基础具有较好的沉贯性能,具有工程实践推广价值。     

复合加载条件下吸力式沉箱基础承载特性数值分析

吸力式沉箱基础的承载特性是海洋工程结构设施建造与设计中的一个关键问题。这种新型的深水海洋基础型式,通常承受竖向上拔荷载与水平荷载的共同作用,其工作性能与设计理论远远不能满足工程实践的需要。本文采用有限元分析方法对吸力式沉箱基础的极限承载特性进行数值计算。以大型通用有限元分析软件ABAQUS为平台,通过二次开发,数值实现了Swipe试验加载方法和固定位移比分析方法,针对不同的沉箱长径比、土的强度折减系数,探讨了沉箱基础在垂直上拔荷载和水平荷载单调联合作用下的极限承载力,通过对不同荷载组合的数值计算构造了复合加载条件下沉箱基础破坏包络面。     

Theoretical studies on penetration resistance of suction caissons in clay

ABSTRACT

The suction caisson is commonly a top-closed cylindrical steel structure with large diameter, short length and much thinner skirt wall thickness. The resistance to penetrating is calculated as the sum of the tip bearing capacity and the adhesion on the both sides of the skirt wall. Since the thickness of the skirt wall is very small, the downward adhesion produced by the skirt wall will cause the additional vertical stress and shear stress in the soil at the skirt tip level, increasing the skirt tip resistance. However, the increase in skirt tip resistance caused by the additional vertical stress rather than shear stress in soil at the skirt tip level was only considered, this may lead to an inaccurate estimation for the tip bearing capacity and the suction required. Thus, a modified slip-line field is put forward in this study to estimate the tip resistance. The expression of obtaining the minimum suction to install the suction caisson in clay is derived in terms of the force equilibrium. Results from calculations of the minimum suction have been proved to be in a good agreement with the measured data.     

Bearing capacity of semi-deep skirted foundations on clay using stress characteristics and finite element analyses

Semi-deep skirted foundations are now considered to be a viable foundation option for a variety of onshore and offshore applications. The capacity under combined vertical, horizontal, and moment loadings must be found to ensure their capability and stability. In this study, undrained bearing capacity subjected to vertical loading, as part of combined loading is determined through stress characteristics and finite element analyses. Circular skirted foundations with different soil strength and geometries considering embedment depth effects have been studied. Stress field, kinematic mechanism accompanying failure, and bearing capacity factors for various embedment ratios are investigated. Acquired vertical failure mechanism has demonstrated the transition from a general shear to a punch shear failure. Comparisons with different research works including conventional methods, upper and lower bound, finite element analyses, physical modeling, experimental, and centrifuge tests have indicated the underestimation of conventional approaches and accuracy of proposed methods in determining bearing capacity. Furthermore, differences between predicted bearing capacities and the results of this study increased with D/B ratio due to ignoring the significant role of skin friction in larger embedment circumference.     

Incremental elastoplastic FEM for simulating the deformation process of suction caissons subjected to cyclic loads in soft clays

This paper presents an incremental elastoplastic finite element method (FEM) to simulate the undrained deformation process of suction caisson foundations subjected to cyclic loads in soft clays. The method is developed by encoding the total-stress-based bounding surface model proposed by the authors in the ABAQUS software package. According to the model characteristics, elastoplastic stress states associated with the incremental strains of each iteration are determined using the sub-incremental explicit Euler algorithm, and the state parameters describing the cyclic accumulative rates of strains are updated by setting state variables during the calculations. The radial fallback method is also proposed to modify the stress states outside the bounding surface to the surface during determination of the elastoplastic stress states. The stress reversals of soil elements are judged by the angle between the incremental deviatoric stress and the exterior normal vector at the image stress point on the bounding surface to update the mapping centre and state variables during cyclic loading. To assess the general validity of the method, the reduced scale model tests and centrifuge tests of suction caissons subjected to cyclic loads are simulated using the method. Predictions are in relative good agreement with test results. Compared with the limit equilibrium and quasi-static methods, the method can not only determine the cyclic bearing capacity, but can also analyse the deformation process and the failure mechanisms of suction caisson under cyclic loads in soft clays.