复合加载条件下吸力式沉箱基础承载特性数值分析

吸力式沉箱基础的承载特性是海洋工程结构设施建造与设计中的一个关键问题。这种新型的深水海洋基础型式,通常承受竖向上拔荷载与水平荷载的共同作用,其工作性能与设计理论远远不能满足工程实践的需要。本文采用有限元分析方法对吸力式沉箱基础的极限承载特性进行数值计算。以大型通用有限元分析软件ABAQUS为平台,通过二次开发,数值实现了Swipe试验加载方法和固定位移比分析方法,针对不同的沉箱长径比、土的强度折减系数,探讨了沉箱基础在垂直上拔荷载和水平荷载单调联合作用下的极限承载力,通过对不同荷载组合的数值计算构造了复合加载条件下沉箱基础破坏包络面。     

复合加载下考虑接触作用的地基承载特性数值分析

港口、海洋工程结构物基础一般处于复合加载状态,其极限承载力通常采用近来引入的极限荷载图进行评价.对位于地基表面的重力式海洋基础,需要考虑基础与地基间的接触特性对极限承载力的影响.以大型通用有限元软件ABAQUS为计算平台,建立了复合加载模式的地基极限承载力数值分析方法;针对饱和黏土地基上的表面基础,利用在ABAQUS平台上开发的接触计算模块,模拟基础与地基间竖向可分离、切向完全粘结的接触作用;进而基于建立的分析方法,进行系统的有限元计算,分析地基的破坏模式随荷载条件的变化,给出地基的极限荷载包络图,并与经典承载力计算公式结果进行对比.研究结果表明,经典承载力计算公式低估了三维荷载条件下的地基极限承载力,有限元计算模型及数值分析方法,可以较好地分析研究地基的失稳机理及承载力特性,并可考虑基础与地基不同的接触条件对破坏模式及组合极限承载力的影响.     

海上风机吸力式桶形基础承载特性研究综述

风机基础作为海上风机整体结构的重要组成部分,承受着上部风机所受到的风浪流荷载,并且对风机的安全性及可靠性至关重要。吸力式桶形基础由于其安装简单和可重复利用等优点,在海洋平台基础中得到了广泛应用,并逐步应用于海上风机基础中。但由于海上风机与海洋平台在海洋环境中的荷载工况有一定的差别,仍需要通过对其承载特性研究现状进行全面认识,以实现吸力式桶形基础在海上风机基础中的可靠应用。文中通过总结和评价现有研究对桶形基础在不同土体条件以及荷载条件下进行试验及数值模拟分析得到的研究结果,综述了静荷载和循环荷载作用下砂土和黏土中的吸力式桶形基础的承载特性研究现状,以及海上风机吸力式桶形基础的相关研究。文章展望了目前应用于海上风机基础的桶形基础仍缺乏的研究,为海上风机吸力式桶形基础的可靠应用及后续研究提供重要参考。     

海上风机吸力式桶形基础承载特性研究述评

风机基础作为海上风机整体结构的重要部分，承受着上部风机所受到的风浪流荷载，并且对风机的安全性及可靠性至关重要。吸力式桶形基础由于其安装简单和可重复利用等优点，在海洋平台基础中得到了广泛应用，并逐步被应用于海上风机基础中。但由于海上风机与海洋平台在海洋环境中的荷载工况有一定的差别，仍需要通过对其承载特性研究现状进行全面认识，以实现吸力式桶形基础在海上风机基础中的可靠应用。本文通过总结和评价现有研究对桶形基础在不同土体条件以及荷载条件下进行试验及数值模拟分析得到的研究结果，综述了静荷载和循环荷载作用下砂土和黏土中的吸力式桶形基础的承载特性研究现状，以及海上风机吸力式桶形基础的相关研究。文章展望了目前应用于海上风机基础的桶形基础仍缺乏的研究，为海上风机吸力式桶形基础的可靠应用及后续研究提供重要参考。     

Spar平台吸力式基础极限承载特性数值分析

以国外某深海Spar平台工程为背景,针对其所采用的细长型吸力式基础的抗拔承载特性进行三维有限元数值分析.分析中充分考虑土体强度、加载位置和加载角度对吸力式基础极限抗拔承载力的影响,本构模型中钢筒基础采用弹塑性模型.分析结果表明,吸力式基础的极限抗拨承载力随着土体强度的增大而增大,倾斜加载时在基础插入土体部分中点左右加载可取得最大的极限承载力,极限抗拔承载力还随着加载角度的增大而增大.吸力式基础存在倾斜加载时桶基础与桶内外土体的共同塑性屈服破坏和垂直加载时桶外土体的局部剪切破坏等两种不同的破坏模式.     

软黏土中桶形基础竖向循环加载超重力离心模型试验研究

桶形基础越来越广泛应用于海洋油气平台、海上风机、输电塔、防波堤等构筑物,研究其循环承载特性对以上构筑物服役安全性具有重要意义。通过在软黏土中开展单桶循环上拔以及小间距群桶循环上拔和循环下压超重力离心模型试验,发现循环上拔地基破坏模式为整体破坏,裂隙均呈现圆弧形,循环下压呈现渐进式整体破坏模式,下压过程的挤压作用可明显减小桶周泥面高度,导致其承载力降低。模拟双向受荷工况的循环上拔试验在5次加载后荷载弱化系数开始趋于稳定,远早于单向受荷工况;单向和双向受荷工况循环上拔荷载弱化系数残余稳定值分别为0.31和0.32,循环下压荷载弱化系数最小值为0.35,表明不同加载方式竖向循环荷载作用下,此三者大小均可用软黏土地基灵敏度倒数预估。     

单向荷载作用下海上风机多桶基础承载特性数值分析

作为一种新型的深水海上基础型式,桶形基础在海上风机设施设计与建设中逐步得到了发展和应用。以三桶基础为例,采用大型有限元软件ABAQUS对海上风机多桶基础的承载特性进行了三维有限元数值分析。根据海上风机的荷载受力特点,分别探讨了三桶基础在竖向荷载、水平荷载和力矩作用下的极限承载力,得出荷载作用方向及桶间距对极限承载力的影响程度,研究成果为复合加载模式下海上风机多桶基础的承载特性分析奠定了基础。     

水平荷载作用下裙式吸力基础承载性能研究

传统吸力基础是一个单桶结构,被广泛作为海洋平台、漂浮结构的基础,近年来也被推广到海上风电塔架。作为风电塔架基础,要充分提高其水平承载能力。为此,提出一种改进的基础形式—裙式吸力基础。采用Z_SOIL有限元软件,针对砂土地基,从水平单调加载和循环加载两个方面,对传统单桶吸力基础和裙式吸力基础进行了承载性能对比研究,得到了相应的荷载-位移曲线。研究结果表明,裙式吸力基础由于设置了"裙"结构,显著提高了其抵抗水平静载和循环水平动力荷载的能力,并能有效控制基础的水平位移,是值得推广应用的一种新型海洋工程基础形式。     

V-M荷载作用下双层黏土地基破坏包络线研究

地基破坏包络线的研究是复合加载模式下地基承载力设计的关键。根据建立的数值计算模型,用Abaqus商业软件分析了V-M荷载作用下,位于双层黏土地基上条形基础的破坏包络线随上层土厚度比、土层强度比的变化规律,以及地基破坏模式随荷载偏心率的变化趋势。用有效面积概念将传统竖向极限承载力换算为V-M荷载平面的破坏包络线,与数值计算结果进行对比。结果表明,公式换算方法适用于均质黏土地基,而对双层黏土地基偏于保守。     

组合荷载作用下伞式吸力锚基础承载特性数值分析

针对用于海上风力发电机的伞式吸力锚基础(USAF)实际条件下的受力特点,采用数值模拟方法,基于大型通用有限元软件ABAQUS构建数值计算模型,对伞式吸力锚基础在H-V、H-T、V-T荷载平面内以及H-V-T非共面复合加载模式下的承载特性进行分析,进而推导其破坏包络面数学表达式。分析中采用固定位移比加载法进行复合加载,并将桶顶位移作为失效破坏标准。结果表明：(1)拟定的应力归一化复合加载破坏包络面椭圆曲线方程可以较好地模拟不同主筒长径比USAF在不同荷载空间内的破坏包络面形式;(2)H-T空间内USAF复合承载性能随主筒长径比(L/D)的增大而提高,而H-V、V-T空间内变化不明显;(3)绘制了H-V-T空间内USAF三维破坏包络面,可根据实际受荷状态与包络面之间的相对位置关系,评价实际工况下伞式吸力锚基础的稳定性。     

V⁃H荷载作用下海洋平台吸力式桩桶桩土承载特性研究

用于海洋平台的吸力式桩桶基础作为一种新型平台基础正逐渐成为人们研究的重点。为研究吸力式桩桶单桩基础的受力特性,对V-H（竖向—水平）联合荷载作用下的吸力式单桩基础桩土的承载特性进行了数值模拟,并将数值模拟的有限元解通过与API规范中对p-y曲线的计算方法进行对比来验证有限元模型的可行性,最后采用分级作用力的加载方式对其破坏包络曲线进行绘制,并推导出相应的函数表达式。研究表明,采用ABAQUS有限元分析软件对吸力式桩桶进行数值模拟是可行的,随着对吸力式桩桶所施加V-H联合荷载的不断增大,吸力式桩桶所能体现的应力和弯矩极限值也在随之增大,其位移变化主要在施加荷载的区域附近,最后在联合荷载作用下所体现的极限承载状态,即包络曲线大致呈四分之一的椭圆形状。     

Effect of embedment on the vertical capacity of bucket foundation in loose saturated sand: Physical modeling

ABSTRACT

Bucket foundations have been widely used for a variety of offshore applications. The effects of skirt length on ultimate bearing capacity of bucket foundation have been studied and reported in published scientific papers. However, few studies have addressed the behavior of bucket foundations in loose saturated sand. In this paper, a series of experimental investigations were performed to determine the bearing capacity of bucket foundation under uniaxial loading. The experiments were conducted on small-scale foundations under vertical loading in loose saturated sand. It was found that increasing the skirt length would enhance the bearing capacity of bucket foundation. As reflected in the present study, bearing strength might be enhanced more than 5 times in loose saturated sand in comparison to surface footing with equivalent diameter. Based on the experimental investigation, a depth factor was proposed to approximate bearing capacity of bucket foundations in terms of those for surface footing and embedment ratio. Moreover, the corresponding settlement of foundation at the failure load was found to increase with skirt length.     

海上风机吸力基础的水平受荷研究综述

吸力基础具有施工速度快、安装过程中受海况天气影响小且易于回收重复利用等优点,被广泛应用于海洋工程。当吸力基础作为海上风电塔架的基础时,常常承受较大的水平荷载,因此其水平承载力是设计的主控因素。介绍了海上风机基础的设计要求,分析了影响基础水平承载性状的因素,总结了吸力基础受水平单调荷载、水平循环荷载和不同荷载组合三个方面的研究现状。讨论了水平荷载的大小、水平加载的高度(偏心率)、循环荷载的频率、循环荷载的次数、循环荷载的幅值、循环荷载的方向性、竖向荷载对吸力基础水平承载性状的影响,考虑了水平荷载的非共线性,指出了目前研究的不足,明确了吸力基础水平承载性状进一步研究的方向,提出了供工程实践参考的建议。     

Bearing capacity of offshore umbrella suction anchor foundation in silty soil under varying loading modes

Considering the current disadvantages of present offshore wind turbine foundations, a novel anchor foundation with skirt and branches is proposed, called offshore umbrella suction anchor foundation (USAF). A series of experiments and numerical simulations were performed to explore the bearing capacity of the USAF under various kinds of loading modes. The bearing characteristics and the anchor–soil interactions are described in detail for horizontal static loading, horizontal cyclic loading, and an antidrawing (pullout) test in silty soil. In the static loading test, the load–deflection of the anchor under step loading was analyzed and the normalized curve of the load–deflection was obtained to determine the ultimate horizontal bearing capacity of the anchor under normal working conditions. Under horizontal cyclic loading, the relationship between the plastic cumulative deformation and cyclic number was determined. In addition, the responses of USAF were investigated for a low wave frequency and storm surges. In the drawing test, it was found that a “segmentation phenomenon” occurred during the test. Moreover, a method to identify the maximum antidrawing load of USAF was provided based on dynamic mechanics. The numerical results show that the use of anchor branches and skirt can enhance the bearing performance of USAF to a certain degree. However, the anchor branch has a slight positive influence on the bearing performance improvement. The USAF is not only similar to a stiff short pile, but a rotation occurs. The failure envelope under composite loading (V-M) was obtained and the changes associated with changes in the aspect ratio of the internal compartment were clarified.     

砂土中四筒导管架风机基础抗弯承载力研究

针对一种四筒导管架海上风机基础,基于有限元数值分析,通过建立砂土中不同筒径和筒高的四筒导管架基础有限元模型,研究砂土中单调弯矩荷载的作用下,筒径与筒高对导管架基础抗弯承载力的影响。分析结果表明:四筒导管架风机基础的抗弯承载力随着筒高或筒径的增加呈明显的增长趋势,相比于筒径的增加,筒高的增加对提高基础抗弯承载力更为有效;在极限弯矩荷载的作用下,基础旋转中心水平向位置受筒高的影响较大,但竖向位置受筒高和筒径的影响很小。     

Evaluation of cyclic and monotonic loading behavior of bucket foundations used for offshore wind turbines

Suction caissons are considered as an alternative foundation solution for offshore wind turbines. In the present study, three-dimensional finite element (FE) analyses are performed to assess the behavior of a bucket foundation and soil supporting the bucket under cyclic and monotonic loading conditions. A parametric study is also performed for a wide range of bucket geometries and two different soil densities. The results indicate that bucket geometry and soil properties significantly affect the foundation response due to cyclic loading conditions. The bucket with the smallest geometry installed in medium dense soil exhibits the lowest stiffness in initial loading and then with the progress of cyclic loads experiences lower stiffness compared to the caissons with larger geometries. The sensitivity of the foundation response to the soil density is higher than its geometry. The bucket under the lowest vertical load experiences the lowest stiffness in both virgin loading and during the progress of cyclic loads. The highest soil displacement is observed near the lid at the interior of the bucket. Stresses caused by cyclic loading belong to certain ranges. Additionally, increases in the skirt length result in increases in the stress ranges and shift the range to the right side. With respect to the monotonic loading conditions, normalized diagrams are proposed that can be used for the preliminary design of suction bucket foundations.     

Stability analysis of suction bucket foundations under wave cyclic loading and scouring

Suction bucket foundation is a typical type for offshore turbines. Scour caused by wave and current can reduce the stability of foundation and then endanger the whole structure. This paper details a series of suction bucket model tests performed in sand under wave cyclic loading. The model tests investigate the effect of scour on stability of bucket foundation by artificially excavated scour hole around the foundation. It is revealed that the behavior of foundation bearing capacity can be divided into two stages: the initial cyclic stage and the final stage (showing either cyclic stability or cyclic failure). When the wave circulation is stable, the sand on the front and back sides of the foundation is suspected to be liquefied. With the increase in scour depth, the stability of foundation is gradually reduced, the behavior of foundation gradually changes from a state of cyclic stability to cyclic failure, and the number of waves that can be withstood is drastically reduced. Finally, the height of the center of rotation of the suction bucket was observed to descend with the increase in scour depth.