Numerical modeling for analyzing thermal surface anomalies induced by underground coal fires

Coal seams burning underneath the surface are recognized all over the world and have drawn increasing public attention in the past years. Frequently, such fires are analyzed by detecting anomalies like increased exhaust gas concentrations and soil temperatures at the surface. A proper analysis presumes the understanding of involved processes, which determine the spatial distribution and dynamic behavior of the anomalies.In this paper, we explain the relevance of mechanical and energy transport processes with respect to the occurrence of temperature anomalies at the surface. Two approaches are presented, aiming to obtain insight into the underground coal fire situation: In-situ temperature mapping and numerical simulation. In 2000 to 2005, annual temperature mapping in the Wuda (Inner Mongolia, PR China) coal fire area showed that most thermal anomalies on the surface are closely related to fractures, where hot exhaust gases from the coal fire are released. Those fractures develop due to rock mechanical failure after volume reduction in the seams. The measured signals at the surface are therefore strongly affected by mechanical processes.More insight into causes and effects of involved energy transport processes is obtained by numerical simulation of the dynamic behavior of coal fires. Simulations show the inter-relation between release and transport of thermal energy in and around underground coal fires. Our simulation results show a time delay between the coal fire propagation and the observed appearance of the surface temperature signal. Additionally, the overall energy flux away from the burning coal seam into the surrounding bedrock is about 30-times higher than the flux through the surface. This is of particular importance for an estimation of the energy released based on surface temperature measurements. Finally, the simulation results also prove that a fire propagation rate estimated from the interpretation of surface anomalies can differ from the actual rate in the seam.     

Impact of lightning on organic matter-rich soils: influence of soil grain size and organic matter content on underground fires

A detailed study was carried out on a piece of land that had been struck by lightning during the violent rainstorm that raged over the Island of S?o Miguel (Azores Archipelago) in late October 2006. Temperature and gas measurements (CO₂, CO, H₂S and CH₄) were performed in four study trenches, dug in an area of ∼3 m², where an underground fire had been initiated by the impact with a lightning stroke, followed by the emission of a column of gases and smoke. The soil under study was originally a well-pedogenized about 80 cm thick bed, made of volcanic clayey to silty tephra fallouts and contained 5.5–9.7% of organic matter. The underground fire was monitored for one week and revealed a peak release of 404 ppm CO and 3.4% CO₂ originating from a horizon located about 45 cm under the soil surface. Measurements of temperature, performed one week after the impact, indicated a maximum value of 326°C inside the soil, while 516.5°C were measured on the surface of a lava block interred about 20 cm under the surface. Subsequently, a stratigraphic and sedimentologic study proved the role of the grain-size of the soil and of the organic matter content of the different horizons of the impact area, in determining the ratio between anoxic/oxidised combustion conditions and in the progress of the process itself. It was also noticed that combustion was not total all over in the soil bed and that the process had slightly migrated toward SW during the observation period. The combustion process went on for about ten days, in spite of several other violent rainstorms, until it was artificially extinguished through the excavations made to obtain study trenches. This particular circumstance evidenced the potential natural hazard represented by this kind of atmospheric event, especially in a land where the volcanic nature of the soil may easily mislead inexperienced observers and, consequently, delay proper action.     

地下矿产开采对天然气管道工程的安全影响评价

西气东输天然气管道工程途经兖州市,穿越杨庄、杨村、兴隆庄等煤矿矿区,压覆煤层埋深变化较大。该文采用预测法对各煤矿在不同开采条件下分煤层对管道运营安全的危害程度进行了评价分析。通过计算表明,煤矿开采埋深越浅,煤层越厚,对管道危害越严重。兴隆庄煤矿3煤层、杨村煤矿煤16t、煤17开采对管道影响强烈,杨庄煤矿煤16t、煤17开采对管道影响中等,兴隆庄煤矿煤16t、煤17开采对管道运营影响小。     

新鲜煤和氧化煤自燃倾向性的FTIR对比分析

利用傅立叶变换红外光谱（FTIR）分析技术,对乌达矿区低温氧化和新鲜煤样进行了红外光谱测试,通过两类煤样的特征官能团吸光度的对比分析．揭示了煤在氧化前后特征官能团的变化规律：氧化后的煤样中脂肪族和芳烃CH减少,酸酐C=O从无到有,芳烃骨架C=C基本不变,进而研究了其对煤自燃倾向性的影响。结果表明脂肪族和羟基含量越高,煤自燃倾向性越大。     

磷处理粉煤灰可作农业土壤磷源

粉煤灰(简称CCP或ash)具有改良土壤,增加植物产量的功能。此外,由于它特殊的多孔结构,也可用作吸纳并承载植物养分的载体。用NaH2PO4配制成含磷0.10mol/L浓度的溶液,对采自加拿大西安大略省Sarnia地区Lambton电厂的底灰(bottomash)进行振荡浸渍处理。结果表明,振荡浸渍66h后的粉煤灰中磷含量可达784×10-6。以磷处理粉煤灰、未进行磷处理的粉煤灰和石英砂按比例混合,作为基本生长介质进行玉米种植实验,其中实验配方设计为生长介质中含磷量分别为标准含磷浓度(50×10-6)的10%、25%、50%、75%和100%。生长26、34和46d后分别与不含磷的空白配方、施加含氮-磷-钾为0-20-0标准磷肥并控制磷含量为标准浓度(50×10-6)配方进行生物产量对比。生长实验结果表明,以磷处理粉煤灰供磷的生长介质,当含磷量为标准浓度的25%至100%时,其植物生长量就比添加标准浓度磷肥的配方好。种植46d后的生物生长量统计结果显示,含磷分别为标准浓度50%、75%和100%的实验介质中,玉米杆的鲜重较施标准磷肥介质中玉米分别增长39.46%、42.73%和46.13%;玉米杆干重依次增加29.71%、13.39%和28.87%;根鲜重平均增加16.62%;根干重平均增加14.03%。上述实验结果启示,粉煤灰可以很好地吸纳承载磷养分,并持续供给植物吸收生长,如果采用吸纳磷(或其他养分)的粉煤灰改良砂质土壤将有重要意义。     

含煤层地质环境下地震波场的数值模拟

本文对含低速煤层地质环境下弹性波场多波多分量地震资料进行了二维数值模拟研究,对人工边界反射进行了有效处理,频散效应得到了有效的压制,对几种不同激发与观测排列方式下的弹性波资料进行了模型计算与分析。     

北京市区春季燃烧源大气颗粒物的污染水平和影响因素

以大气中PM2.5和PM10为研究对象,于2005-03-13—25共7天的时间内,在中国地质大学(北京)测试楼顶、首钢焦化厂和首钢东门设立3个采样点进行采样监测。结果表明:PM2.5和PM10质量浓度的日变化呈现一定规律性,在不同时段PM2.5和PM10的质量浓度不尽相同,且变化较大,在特定时刻出现峰值,主要受污染源排放和气象因素的控制;PM2.5和PM10质量浓度随气温的升高而降低,这与高温有利于颗粒物扩散、低温容易形成逆温层有关;在一定的相对湿度范围内(以大气中水汽不发生重力沉降为界限),PM2.5和PM10质量浓度与相对湿度呈正相关关系;而当发生降水时,由于水滴的冲刷和附带作用,PM2.5和PM10质量浓度降低;PM2.5和PM10质量浓度与风级呈明显的负相关关系。通过北京市与国内8个省会城市的PM2.5和PM10质量浓度的对比,发现北京市PM2.5和PM10污染比较严重,PM2.5和PM10质量浓度分别超过了1996年中国制定的PM10排放标准和1997年美国EPA制定的PM2.5排放标准。     

Mechanisms of coal metamorphism: case studies from Paleozoic coalfields

Controls on coal metamorphism can be complex. In this paper, we examine four Paleozoic coalfields: the western Kentucky portion of the Illinois Basin, the Pennsylvania anthracite fields, the South Wales Coalfield, and the Bowen Basin. An increase in temperature with depth of burial is certainly a factor in coal metamorphism. In many coalfields, however, including the coalfields reviewed here, it has become apparent that such a simple mechanism does not explain the coal rank patterns observed. The flow of hydrothermal fluids through the coals has been proposed as a cause of coal metamorphism. Evidence includes inverted rank gradients, elevated CFL as an indicator of brine fluids, isotopic evidence for hydrothermal fluids, and vein and cleat mineral assemblages. In any case, multiple hypotheses must often be evaluated in the examination of any coalfield since the simple paradigm of coal rank increases with a simple increase in temperature with increasing depth does not fit the evidence observed in many cases.     

Coal mining along the Warfield Fault, Mingo County, West Virginia: a tale of ups and downs

Mine development along a 15-mile (24 km) section of the Warfield Fault in Mingo County, West Virginia has broadened the geological understanding of the fault and its related structures. The fault has been exposed in two new road cuts, one in the northeast-trending segment at Neely Branch and one in the eastern east-trending segment at the head of Marrowbone Creek. Both exposures show a well-defined normal fault with a 45° to 55° N dip, juxtaposing sandstone/shale packages from the roof and the floor of the Coalburg seam. The fault is associated with a thin gouge zone, some drag folding, and parallel jointing. Its trace tends to run parallel to the crest of the adjacent Warfield Anticline. Based on underground mine development and detailed core drilling, the vertical offset along the fault plane ranges from a maximum of 240 ft (73 m) in the central part of the area near the structural bend to less than 100 ft (30 m) in western and eastern directions. The fault is located along the relatively steeply dipping (locally in excess of 25%) southern limb of the Warfield Anticline, and appears related to a late phase of extension involving folded Pennsylvanian strata. On a regional scale, the lithological variations across the fault do not suggest any appreciable strike-slip component.Underground room and pillar mines in the Coalburg seam north and south of the fault have been greatly impacted by the Warfield structures. Due to the combined (and opposite) effects of the folding and faulting, the northern mines are located up to 400 ft (125 m) higher in elevation than the southern ones. Overland conveyor belts connect mining blocks separated by the fault. The practical mining limit along the steep slopes toward the fault is around 15%. Subsidiary normal faults with offsets in the 5- to 15-ft (1.5–4.5 m) range are fairly common and form major roof control and production hurdles. Overall, the Warfield structures pose an extra challenge to mine development in this part of the Appalachian Coalfields.     

Surface analysis of pyrite in the No. 9 coal seam, Wuda Coalfield, Inner Mongolia, China, using high-resolution time-of-flight secondary ion mass-spectrometry

The chemical composition of pyrite in coal can be used to investigate its geological and mineralogical origin. In this paper, high-resolution time-of-flight secondary ion mass spectrometry (TOF-SIMS) was used to study the chemical composition of various pyrite forms in the No. 9 coal seam (S_t,d=3.46%) from the Wuda Coalfield, Inner Mongolia, northern China. These include bacteriogenic, framboidal, massive, cell-filling, fracture-filling, and nodular pyrites. In addition to Fe⁺ (⁵⁴Fe⁺, ⁵⁶Fe⁺, ⁵⁷Fe⁺), other fragment ions were detected in bacteriogenic pyrites, such as ²⁷Al⁺, Si⁺ (²⁸Si⁺, ²⁹Si⁺, ³⁰Si⁺), ⁴⁰Ca⁺, Cu⁺ (⁶³Cu⁺, ⁶⁵Cu⁺), Zn⁺ (⁶⁴Zn⁺, ⁶⁶Zn⁺, ⁶⁷Zn⁺, ⁶⁸Zn⁺), Ni⁺ (⁵⁸Ni⁺, ⁶⁰Ni⁺, ⁶²Ni⁺), and C₃H₇⁺. TOF-SIMS images show bacteriogenic pyrites are relatively rich in Cu, Zn, and Ni, suggesting that bacteria probably play an important role in the enrichment of Cu, Zn, and Ni during their formation. Intense positive secondary ion fragments from framboidal aggregates, such as ²⁷Al⁺, ²⁸Si⁺, ²⁹Si⁺, AlO⁺, CH₂⁺, C₃H₃⁺, C₃H₅⁺, and C₄H₇⁺, indicate that formation of the framboidal aggregates may have occurred together with clay mineral and organic matter, which probably serve as the binding substance. The intense ions of ²⁸Si⁺ and ²⁷Al⁺ from massive pyrites also suggest that their pores incorporated clay minerals during crystallization. Together with the lowest ²⁸Si⁺/²³Na⁺ value, the intense organic positive secondary ion peaks from cell-filling pyrites, such as C₃H₃⁺, C₃H₅⁺, C₃H₇⁺, and C₄H₇⁺, indicate that pyrite formation may have accompanied dissolution or disintegration of the cell. The intense P⁺ peak was observed only in the fracture-filling pyrite and the highest ²⁸Si⁺/²³Na⁺ value of fracture-filling pyrite reflects its epigenetic origin. Together with XRD and REEs data, the stronger ⁴⁰Ca⁺ in nodular pyrite than other pyrite forms shows seawater influence during its formation.