渤、黄、东海底摩擦系数的研究

本文将伴随法用于渤、黄、东海M2分潮的数值模拟,利用Topex／Poseidon高度计资料进行同化,优化海底摩擦系数。文中对底摩擦系数取常数时进行了优化,同时还对底摩擦系数的一种新的处理方法进行了研究,即在计算海区选取一些点给定底摩擦系数,海区中任意一点的底摩擦系数由这些点的底摩擦系数线性播值得到,优化后得到空间分布的底摩擦系数。针对两种不同的线性底摩擦假设分别进行了一系列的实际实验,结果表明由空间分布的底摩擦系数得到的模拟值比底摩擦系数取常数得到的模拟值更接近观测值,能有效地提高数值模拟的精度。     

On the radiation and diffraction of linear water waves by an infinitely long rectangular structure submerged in oblique seas

The radiation and diffraction of linear water waves by an infinitely long rectangular structure submerged in oblique seas of finite depth is investigated. The analytical expressions for the radiated and diffracted potentials are derived as infinite series by use of the method of separation of variables. The unknown coefficients in the series are determined by the eigenfunction expansion matching method. The expressions for wave forces, hydrodynamic coefficients and reflection and transmission coefficients are given and verified by the boundary element method. Using the present analytical solution, the hydrodynamic influences of the angle of incidence, the submergence, the width and the thickness of the structure on the wave forces, hydrodynamic coefficients, and reflection and transmission coefficients are discussed in detail.     

浮体间距对多浮体系统水动力系数的影响

根据三维线性势流理论，采用格林函数法，对多浮体系统的水动力系数进行了数值分析。数值算例中给出了在固定波频下水动力系数与浮体间相对位置关系曲线。水动力系数的变化幅度随着浮体间距离增大而变小。随着浮体间距的变化，水动力系数极值的出现具有明显的规律，相邻的极大值(或极小值)的间距为半个波长或一个波长。     

Performance of hemi-cylindrical and rectangular submerged breakwaters

A parametric experimental study is conducted to compare the reflection and transmission characteristics of submerged hemi-cylindrical and rectangular rigid and water-filled flexible breakwater models. The results show that, for the rigid breakwaters, rectangular models are more effective than hemi-cylindrical ones in terms of reduction of transmitted waves. As for the flexible breakwaters, the hemi-cylindrical models may give better wave reflection than rectangular ones. However, the energy loss induced by the rectangular breakwaters is much larger and more significant to result in an overall better efficiency in terms of reduction in wave transmission. The effects of internal pressure show that the lowest pressurized flexible models considered in this work are the most effective in the reduction of the transmitted wave height. Higher wave reflection, lower wave transmission and higher energy loss are obtained consistently at the lower submergence depth ratio.     

基于岭估计的有理多项式参数求解方法

在使用最小二乘法解算卫星遥感影像的RPC参数时,如果控制点非均匀分布或模型过度参数化,其法方程系数矩阵很容易产生病态,获得的解将偏离真值,甚至得到错误的解.使用岭估计可改善法方程的状态,保证解稳定.采用岭估计方法,通过所获取的不同岭参数对SPOT和QuickBird影像进行实验,证实L曲线法是一种稳定的、有效的岭参数确定方法,可显著提高RPC参数的解算精度.     

A laboratory experiment to monitor the contact state of a fault by transmission waves

We performed a series of laboratory experiments in which elastic waves were transmitted across a simulated fault. Two types of experiments were carried out: (1) Normal Stress Holding Test (NSHT): normal stress was kept constant for about 3 h without shear stress and transmission waves were observed. (2) Shear Stress Increasing Test (SSIT): shear stress was gradually increased until a stick-slip event occurred. Transmission waves were continuously observed throughout the process of stress accumulation. We focused on the change in transmission waves during the application of shear stress and especially during precursory slips.It was found in NSHT that the amplitude of transmission waves linearly increased with the logarithm of stationary contact time. The increase amounted to a few percent after about 3 h. Creep at asperity contacts is responsible for this phenomenon. From a theoretical consideration, it was concluded that the real contact area increased with the logarithm of stationary contact time.We observed in SSIT a significant increase in wave amplitude with shear stress application. This phenomenon cannot be attributed to the time effect observed in NSHT. Instead, it can be explained by the mechanism of “junction growth” proposed by Tabor. Junction growth yields an increase in real contact area. It is required for junction growth to occur that the material in contact is already plastic under a purely normal loading condition. A computer simulation confirmed that this requirement was satisfied in our experiments. We also found that the rate at which the amplitude increased was slightly reduced prior to a stick-slip event. The onset time of the reduction well coincides with the onset of precursory slip. The cause of the reduction is attributed to the reset of stationary contact time due to displacement. This interpretation is supported by the result of NSHT. Taking the time of stationary contact in SSIT into account, we may expect the change in wave amplitude to be, at most, only a few percent. The observed slight reduction in increasing rate is, in this sense, reasonable. The static stiffness of the fault also decreases with precursory slip. It was also found that low frequency waves are a better indicator of precursory slip than high frequency waves. This might suggest that low frequency waves with longer wavelength are a better indicator of average behavior of faults. The problem, however, merits a further investigation. The shifts in phase were also found to be a good indicator of the change in contact state of the fault. The changes in both amplitude and phase of transmission waves are unifyingly understood through the theory of transmission coefficient presented by Pyrak-Nolte et al. Rough surfaces have a tendency to give larger stick-slips than smooth surfaces. The amount of precursory slip is larger for rough surfaces than for smooth surfaces. Although it was confirmed by a computer simulation that rough surfaces have larger contact diameters than smooth surfaces, the rigorous relationship between the surface roughness (contact diameter) and the amount of precursory slips was not established.     

苯和甲苯在盐水溶液中活度系数及其盐效应的研究

采用紫外分光光度法测定了24.0℃时苯和甲苯在CH3COONa,(NH4)2SO4,MgSO4,Na2SO4和Na2CO3水溶液中的活度系数(f),它们的lgf-Cs关系符合Setschenow盐效应公式,计算了苯和甲苯在上述5种盐水溶液中的盐析系数。     

Determining Q of near-surface materials from Rayleigh waves

High-frequency (≥2 Hz) Rayleigh wave phase velocities can be inverted to shear (S)-wave velocities for a layered earth model up to 30 m below the ground surface in many settings. Given S-wave velocity (V_S), compressional (P)-wave velocity (V_P), and Rayleigh wave phase velocities, it is feasible to solve for P-wave quality factor Q_P and S-wave quality factor Q_S in a layered earth model by inverting Rayleigh wave attenuation coefficients. Model results demonstrate the plausibility of inverting Q_S from Rayleigh wave attenuation coefficients. Contributions to the Rayleigh wave attenuation coefficients from Q_P cannot be ignored when Vs/V_P reaches 0.45, which is not uncommon in near-surface settings. It is possible to invert Q_P from Rayleigh wave attenuation coefficients in some geological setting, a concept that differs from the common perception that Rayleigh wave attenuation coefficients are always far less sensitive to Q_P than to Q_S. Sixty-channel surface wave data were acquired in an Arizona desert. For a 10-layer model with a thickness of over 20 m, the data were first inverted to obtain S-wave velocities by the multichannel analysis of surface waves (MASW) method and then quality factors were determined by inverting attenuation coefficients.