Shear Failure of a Clamped Dented Tubular Beam Under Lateral Impact

- The shear failure of a rigid-plastic dented clamped tubular beam under the lateral impact of a mass is investigated. Both the denting and the impact point are in the middle span of the beam. It is assumed that denting does not spread during the shear sliding. Numerical results show that the axial force and lateral deflection of the beam are very small at the moment of the occurence of shear failure, which means that the finite deformation effect can be neglected in the shear failure analysis. Also, some aspects of the initial impact energy are investigated.     

Elasto-Plastic Analysis of Tubular Joints of Offshore Platforms by Finite Element Method

The plastic node method is reformulated by the variational principle and is applied to elasto-plastic finite element analysis of tubular joints, eventually including the effect of internal and external gussets, stiffener rings, etc., if necessary. Four different joints are studied here in detail for the elasto-plastic behavior, the strain at the hot spot, the strain concentration factor around the intersection line, and the propagation of the plastic region with loading up to collapse in order to determine the ultimate strength, safety factor, and development of the plastic field. The present results are in good agreement with the experimental results.     

非常规管节点疲劳寿命分析与计算

对非常规管节点的疲劳寿命进行了分析研究，用SESAM计算疲劳载荷，应用精细有限元分析计算热点应力，用规范的S—N曲线计算管节点的疲劳寿命。通过实例计算表明，这些处理对非常规管节点疲劳寿命分析与计算是很有效的。     

Regression Formulations for the Stress at Hot Spot of Multiplanar Tubular DT Joints

- Stress concentration analysis of multiplanar tubular DT joints plays an important role in the fatigue design of offshore platforms. A semi-analytic method for stress analysis under the condition of any loads is briefly introduced in the paper. Nineteen multiplanar tubular DT joints with one of two braces of the same dimension subjected to axial loads and out- of- plane bending moments are computed for parametric stress analysis by using the present method. The influence of geometrical parameters on the stresses of multiplanar tubular DT joints is discussed and compared with corresponding uniplanar T joints. The regression formulae for the stress at hot spot of multiplanar DT joints are found by modification of SCF of corresponding uniplanar T joints. The parametric formulae for the maximum stress by superposition. Finally, the influences of stiffening effect and load-interaction effect on the maximum stress of DT joints are discussed.     

The origin of the Pedra Furada sandstone tubular structures (South of Lisbon, Portugal)

The Pedra Furada is a 12 m wide, 18 m high outcrop feature showing hundreds of ferruginised sandy tubes and looking in part like a giant organ. In this paper the origin of the tubes is explained on the basis of geochemical, petrographic and microscopic (optical and electronic) analytical data. The tubes are considered to represent vertical escape channels for overpressured water, exhibiting inward decreasing grain size due to water velocity gradients inside the escape channels. The ferruginisation is due to iron oxides associated with colloidal/clayey fine sediments and to goethite formed from solution. The overpressure of water may be due to seismically fluidised beds below the Pedra Furada outcrop or to artesian water ascent. In both cases, fault rupturing may have played a major role in the focussing of the ascending flow.     

部分预应力混凝土扁梁框架节点的拟静力试验研究

本文进行了四个部分预应力混凝土扁梁框架节点的拟静力试验研究。通过四个不同试件的试验研究分析了节点的变形能力、耗能能力、延性和刚度退化等抗震性能，同时分析了低周反复荷载作用下预应力混凝土框架节点的破坏机理。     

Anisotropic damage of rock joints during cyclic loading: constitutive framework and numerical integration

This work describes a constitutive framework for modeling the behavior of rough joints under cyclic loading. Particular attention is paid to the intrinsic links between dilatancy, surface degradation, and mobilized shear strength. The framework also accounts for the important effect of shear‐induced anisotropy. The resulting approach is fully three‐dimensional and is not restricted to plane‐displacement kinematics. Both the governing formulation and an algorithm for implicit numerical integration are presented. While the proposed methods are general, we also postulate a specific model that is compared with experimental data. It employs relatively few free parameters but shows good agreement with laboratory tests. Copyright © 2013 John Wiley & Sons, Ltd.     

Residual compressive strength of inclined steel tubular members with local corrosion

In jacket-type offshore structures, corrosion damage affects the structural performance under compressive loading, which is created by the working and design loads of the main system. In this study, the effects of corrosion damage on the compressive structural behavior and strength of steel tubular members were investigated. Artificial corrosion damage was applied to the tubular specimens via mechanical processing and hand drilling to replicate the inclined nature of jacket-type offshore structures. The damage was applied to either half or all of the circumference of the specimens. The compressive failure modes of the artificially corroded tubular members were affected by the corrosion conditions. The compressive strengths were also affected by the level of corrosion. From the results of this study, the residual compressive strengths of corroded tubular steel members can be estimated based on the condition of the damaged sectional areas.     

消能减震高层方钢管混凝土框架结构振动台试验研究和弹塑性时程分析

本文首先介绍了一幢安装了粘滞阻尼器的复杂体型高层方钢管混凝土框架结构的1/15缩尺模型的模拟地震振动台试验结果;在此基础上,建立了梁、柱构件的多弹簧模型并组建了整体结构的计算分析模型,运用此计算模型首先对试验模型结构进行了动力弹塑性时程分析,计算结果和试验结果吻合较好,验证了计算模型的正确性;最后,以同样方法对原型结构进行了计算分析,并结合试验结果研究探讨了此结构的抗震性能和阻尼器的消能减震效果。结果表明:该结构未出现明显的薄弱层,能够满足规范的抗震设防要求,阻尼器发挥了一定的消能减震效果,进一步提高了结构的抗震性能。