Consolidation of double‐layered ground with vertical drains

Vertical drains are usually installed in subsoil consisting of several layers. Due to the complex nature of the problem, over the past decades, the consolidation properties of multi‐layered ground with vertical drains have been analysed mainly by numerical methods. An analytical solution for consolidation of double‐layered ground with vertical drains under quasi‐equal strain condition is presented in this paper. The main steps for the computation procedure are listed. The convergence of the series solution is discussed. The comparisons between the results obtained by the present analytical method and the existing numerical solutions are described by figures. The orthogonal relation for the system of double‐layered ground with vertical drains is proven. Finally, some consolidation properties of double‐layered ground with vertical drains are analysed. Copyright © 2001 John Wiley & Sons, Ltd.     

A continuum‐discrete hydromechanical analysis of granular deposit liquefaction

A coupled continuum‐discrete hydromechanical model was employed to analyse the liquefaction of a saturated loose deposit of cohesionless particles when subjected to a dynamic base excitation. The pore fluid flow was idealized using averaged Navier–Stokes equations and the discrete element method was employed to model the solid phase particles. A well established semi‐empirical relationship was utilized to quantify the fluid–particle interactions. The conducted simulations revealed a number of salient micro‐mechanical mechanisms and response patterns associated with the deposit liquefaction. Space and time variation of porosity was a major factor which affected the coupled response of the solid and fluid phases. Pore fluid flow was within Darcy's regime. The predicted response exhibited macroscopic patterns consistent with experimental results and case histories of the liquefaction of granular soil deposits. Copyright © 2004 John Wiley & Sons, Ltd.     

Use of multi‐platform,multi‐temporal remote‐sensing data for calibration of a distributed hydrological model: an application in the Arno basin,Italy

Images from satellite platforms are a valid aid in order to obtain distributed information about hydrological surface states and parameters needed in calibration and validation of the water balance and flood forecasting. Remotely sensed data are easily available on large areas and with a frequency compatible with land cover changes. In this paper, remotely sensed images from different types of sensor have been utilized as a support to the calibration of the distributed hydrological model MOBIDIC, currently used in the experimental system of flood forecasting of the Arno River Basin Authority. Six radar images from ERS‐2 synthetic aperture radar (SAR) sensors (three for summer 2002 and three for spring–summer 2003) have been utilized and a relationship between soil saturation indexes and backscatter coefficient from SAR images has been investigated. Analysis has been performed only on pixels with meagre or no vegetation cover, in order to legitimize the assumption that water content of the soil is the main variable that influences the backscatter coefficient. Such pixels have been obtained by considering vegetation indexes (NDVI) and land cover maps produced by optical sensors (Landsat‐ETM). In order to calibrate the soil moisture model based on information provided by SAR images, an optimization algorithm has been utilized to minimize the regression error between saturation indexes from model and SAR data and error between measured and modelled discharge flows. Utilizing this procedure, model parameters that rule soil moisture fluxes have been calibrated, obtaining not only a good match with remotely sensed data, but also an enhancement of model performance in flow prediction with respect to a previous calibration with river discharge data only. Copyright © 2006 John Wiley & Sons, Ltd.     

Size and shape evolution of pores in a viscoplastic matrix under compression

The frequent use of soils and earth materials for hydraulic capping and for geo‐environmental waste containment motivated our interest in detailed modelling of changes in size and shape of macro‐pores to establish links between soil mechanical behaviour and concurrent changes in hydraulic and transport properties. The objective of this study was to use finite element analysis (FEA) to test and extend previous analytical solutions proposed by the authors describing deformation of a single macro‐pore embedded in linear viscoplastic soil material subjected to anisotropic remote stress. The FEA enables to consider more complex pore geometries and provides a detailed picture of matrix yield behaviour to explain shortcomings of approximate analytical solutions. Finite element and analytical calculations agreed very well for linear viscous as well as for viscoplastic materials, only limited for the case of isotropic remote stress due to the simplifications of the analytical model related to patterns and onset of matrix‐yielding behaviour. FEA calculations were compared with experimental data obtained from a compaction experiment in which pore deformation within a uniform modelling clay sample was monitored using CAT scanning. FEA predictions based on independently measured material properties and initial pore geometry provided an excellent match with experimentally determined evolution of pore size and shape hence lending credence to the potential use of FEA for more complex pore geometries and eventually connect macro‐pore deformation with hydraulic properties. Copyright © 2006 John Wiley & Sons, Ltd.     

Generalized strain probing of constitutive models

Advanced material constitutive models are used to describe complex soil behaviour. These models are often used in the solution of boundary value problems under general loading conditions. Users and developers of constitutive models need to methodically investigate the represented soil response under a wide range of loading conditions. This paper presents a systematic procedure for probing constitutive models. A general incremental strain probe, 6D hyperspherical strain probe (HSP), is introduced to examine rate‐independent model response under all possible strain loading conditions. Two special cases of HSP, the true triaxial strain probe (TTSP) and the plane‐strain strain probe (PSSP), are used to generate 3‐D objects that represent model stress response to probing. The TTSP, PSSP and general HSP procedures are demonstrated using elasto‐plastic models. The objects resulting from the probing procedure readily highlight important model characteristics including anisotropy, yielding, hardening, softening and failure. The PSSP procedure is applied to a Neural Network (NN) based constitutive model. It shows that this probing is especially useful in understanding NN constitutive models, which do not contain explicit functions for yield surface, hardening, or anisotropy. Copyright © 2004 John Wiley & Sons, Ltd.     

The influence of a non‐associated flow rule on the calculation of the factor of safety of soil slopes

This paper presents a method that incorporates a non‐associated flow rule into the limit analysis to investigate the influence of the dilatancy angle on the factor of safety for the slope stability analysis. The proposed method retain's the advantage of the upper bound method, which is simple and has no stress involvement in the calculation of the energy dissipation and the factor of safety. Copyright © 2001 John Wiley & Sons, Ltd.     

Recurrent Red-tides in the Southampton Water Estuary Caused by the Phototrophic CiliateMesodinium rubrum

In the Southampton Water estuary (southern England, U.K.), red-tides caused by the planktonic, phototrophic ciliateMesodinium rubrum(=Myrionecta rubra) occur during most summers and sometimes in autumn. These events were investigated in detail between 1985 and 1987 and were characterized by levels of chlorophylla(chl a) of over 100 μg l⁻¹, cell numbers ofM. rubrumof over 1×10³ ml⁻¹, oxygen saturations of around 150%, and depleted numbers of macrozooplankton. Initiation of red-water did not appear to be triggered by irradiance or nutrients, but coincided with an increase in temperature and water column stability. This enhanced stability was promoted by increased surface to bottom gradients of both temperature and salinity, and by reduced mixing during neap tides. Development of red-water was accompanied by removal of most of the dissolved NH⁺₄from the water column, whereas some NO⁻₃persisted, presumably maintained by freshwater input. NO⁻₃and NH⁺₄gradually returned to pre-bloom concentrations as the red-water declined in late summer. Maximal biomass ofM. rubrumappeared to be limited by irradiance, and self-shading probably imposed an upper limit of around 300 mg chl a m⁻²within the water column. At the observed levels of chl a, irradiance values within the population maximum between 1 and 3 m depth were only just of the order (≈15 μmol photons m⁻² s⁻¹) required to balance estimated respiratory demands. Oxygen concentration became undersaturated during the late bloom phase, with minimal values of 20–30% saturation recorded in deeper waters; however, despite this and reduced numbers of macrozooplankton, direct deleterious effects on other organisms were not observed.     

Simulating methane emission from a Chinese rice field as influenced by fertilizer and water level

Natural and agricultural wetlands are considered to be the major sources of global atmospheric methane (CH₄). A one‐dimensional model was developed to simulate methane emission and used to examine the influence of various physical processes on the rate of methane emission. Three processes involved in the methane emission are implemented in the model: production, reoxidation and transport. Three transport pathways were considered: diffusion across water–air or soil–air interfaces, ebullition and diffusion through plants. These pathways are influenced by soil properties, plant growth, water‐table conditions, temperature and external inputs (e.g. fertilizer). The model was used to examine the seasonal variation of the methane emission at a rice field in Hunan, China, which was observed during a field experiment for consecutive (early and late) rice seasons in 1992. The observed seasonal variations of methane emission, and role of plants in transporting methane to the atmosphere, are captured by the model simulation. Further model applications were conducted to simulate effects of fertilizer and water‐level condition on the methane emission. The results indicate that unfermented organic fertilizer produces a higher methane emission rate than mineral fertilizer. The simulations with treatments of a deep‐water covering and constant moisture reduced the methane emission. The rice field study provides a framework for further development of the model towards simulations based on spatially distributed variables (e.g. water table, soil temperature and vegetation) at a regional scale. Copyright © 2003 John Wiley & Sons, Ltd.     

Estimation of snow water equivalent using microwave radiometry over Arctic first‐year sea ice

The magnitude and spatial distribution of snow on sea ice are both integral components of the ocean–sea‐ice–atmosphere system. Although there exists a number of algorithms to estimate the snow water equivalent (SWE) on terrestrial surfaces, to date there is no precise method to estimate SWE on sea ice. Physical snow properties and in situ microwave radiometry at 19, 37 and 85 GHz, V and H polarization were collected for a 10‐day period over 20 first‐year sea ice sites. We present and compare the in situ physical, electrical and microwave emission properties of snow over smooth Arctic first‐year sea ice for 19 of the 20 sites sampled. Physical processes creating the observed vertical patterns in the physical and electrical properties are discussed. An algorithm is then developed from the relationship between the SWE and the brightness temperature measured at 37 GHz (55°) H polarization and the air temperature. The multiple regression between these variables is able to account for over 90% of the variability in the measured SWE. This algorithm is validated with a small in situ data set collected during the 1999 field experiment. We then compare our data against the NASA snow thickness algorithm, designed as part of the NASA Earth Enterprise Program. The results indicated a lack of agreement between the NASA algorithm and the algorithm developed here. This lack of agreement is attributed to differences in scale between the Special Sensor Microwave/Imager and surface radiometers and to differences in the Antarctic versus Arctic snow physical and electrical properties. Copyright © 2003 John Wiley & Sons, Ltd.