Problems of soil and groundwater pollution in the disposal of “marble” slurries in NW Sicily

This work deals with disposal of slurries generated during the cutting and polishing processes of slabs of decorative sedimentary carbonate rocks in the north western Sicily. At present, they are used as fillers of dismantled quarries near the sawmills and, as a final step of reclamation, are covered with earth layers. In spite of such inexpensive solution, there is lack of knowledge about the composition of the waste. In order to assess if there is any threat for the environment and to suggest indications for alternative solutions, such as recycling or inactivation processes, the slurries were analysed by XR diffraction, simultaneous thermal analysis, ICP/MS, ionic chromatography, FTIR, UV-Vis, COD and TOC measurements, grain size analysis. Results indicate that the slurries can threaten the groundwater, because of the high chemical oxygen demand; furthermore they can modify the mechanism of groundwater recharge, because of their grain size distribution. Some laboratory tests show that, even in very aggressive conditions, the solid pollutants persist in the waste and slowly release into water the products of their degradation. The slurry therefore should be subjected to inactivation treatment before disposal or, alternatively, recycled as secondary raw material for a suitable process.     

岩石圈中热压系数的计算

中国中西部地区发育众多前陆冲断带,它们具有构造变形复杂、油气潜力大和有别于经典前陆盆地的沉积和油气地质特征,但其成因过程和动力学并不清楚。文中利用中西部盆地区的地温、岩石热物性参数和地热学模拟技术,分析该区岩石圈热状态和流变学特征,进一步结合其他地质、地球物理资料,揭示盆地区的深部构造特征和岩石圈性质。研究表明,中西部各主要盆地的岩石圈具有厚度大、强度高、地温低等热-流变学特征,表现为刚硬块体;而其周缘和造山带区却表现为温度高、强度低和厚度小等特征,是构造变形的易发区。在此基础上讨论了岩石圈性质和变形过程等深部构造对前陆盆地成因演化的控制作用,进而初步归纳这类陆内再生前陆盆地的成因演化机制:发育于小型克拉通块体的边缘,其就位受控于岩石圈热-流变学非均质性和构造继承性,其动力来源是新生代印度-欧亚大陆碰撞及其持续的挤压作用。上述研究为探讨中国中西部地区的前陆盆地成因机制提供了深部资料和岩石圈热-流变学约束。     

Performance of Mortar and Chemical Grout Injection into Surrounding Soil When Slurry Pipe-jacking Method is Used

Small-diameter shallow tunnels are often being built by using the slurry pipe-jacking method. This system involves the pushing or thrusting of a drivage machine and concrete pipes into the ground. Chemical grout injection into the surrounding soil around the tunnel is carried out after the drivage and pushing processes are finished. The purpose of the chemical grout injection is to maintain permanent stability of the surrounding soil. However, the behavior of the chemical grouting material in the surrounding soil around the tunnel and the amount of optimum injection is not clearly understood. From these points of view, this paper discusses the performance of the chemical grouting material, when it is injected into the surrounding soil around the tunnel, by means of 2-D Eulerian–Lagrangian seepage analysis. Moreover, the effectiveness of the chemical grout injection was evaluated by using the non-linear finite element method. This investigation show when the range of the grouted zone is designed; it is necessary that the relationship between Young’s modulus of the soil/grouted zone and the confining stress be taken into consideration in order to establish effective, economical and safe chemical grout injection system. Understanding the performance of the seepage/dispersion behavior of the chemical grout and the characteristics of soil/ grouted zone is also important.     

Interpretation of subhorizontal crustal reflections by metamorphic and rheologic effects in the eastern part of the Pannonian Basin

The geologic origin of subhorizontal reflections, often observed in crustal seismic sections, was investigated by establishing metamorphic facies and strength of rocks in depth, and correlating these properties to seismic reflection sections from eastern Hungary. Estimation of the depths of metamorphic mineral stability zones utilized the principles developed by Fyfe et al. and known geothermal data of the area. The strength versus depth profile was derived by relating local seismic P -wave interval velocities to Meissner et al. 's activation energy. The results show that the series of subhorizontal reflections, observed in the Pannonian Basin, are a consequence of combined metamorphic and rheologic changes in depths. The synthesis of the integrated data set suggests that the retrograde alteration of the pre-Tertiary basement above the percolation threshold was made possible by the softening effect of shear zones and their water-conducting capacity. The subhorizontal reflections of highest energy, of the consolidated crust below the percolation threshold, originate in the depths of greenschist, amphibolite and granulite metamorphic mineral facies, which were formed in geothermal and pressure conditions similar to those existing today. These results imply the overprint of earlier (Variscan) metamorphic sequences of the crust by more recent retrograde metamorphic processes.     

Monitoring of Over Cutting Area and Lubrication Distribution in a Large Slurry Pipe Jacking Operation

Slurry pipe jacking was firmly established as a special method for the non-disruptive construction of the underground pipelines of sewage systems. Pipe jacking, in its traditional form, has occasionally been used for short railways, roads, rivers, and other projects. Basically the system involves the pushing or thrusting of concrete pipes into the ground by a number of jacks. In slurry pipe jacking, during the pushing process, mud slurry and lubricant are injected into the face and the over cutting area that is between the concrete pipes and the surrounding soil. Next, the slurry fills voids and the soil stabilizes due to the created slurry cake around the pipes. Fillings also reduce the jacking force or thrust during operation. When the drivage and pushing processes are finished, a mortar injection into the over cutting area is carried out in order to maintain permanent stability of the surrounding soil and the over cutting area. Successful lubrication around the pipes is extremely important in a large diameter slurry pipe jacking operation. Control of lubrication and gaps between pipes and soil can prevent hazards such as surface settlement and increases in thrust. Also, to find voids around the pipes after the jacking process, in order to inject mortar for permanent stabilizing, an investigation around the pipes is necessary. To meet these aims, this paper is concerned with the utilization of known methods such as the GPR (Ground Penetrating Radar) system and borehole camera to maintain control of the over cutting area and lubricant distribution around the pipes during a site investigation. From this point of view, experiments were carried out during a tunnel construction using one of the largest cases of slurry pipe jacking in Fujisawa city, Japan. The advantages and disadvantages of each system were clarified during the tests.