Multiple longshore sand bars in the upper Chesapeake Bay

In the upper Chesapeake Bay (Maryland, U.S.A.) field surveys were conducted at 18 multiple longshore sand bar sites. The multiple bar systems were found in water depths less than approximately 2 m (mean sea level), and exhibited mild bottom slopes of 0·0052 or less. The number of bars composing each system ranged from four to 17 and the spacing between the crests typically increased in the offshore direction, ranging from 12 to 70 m. Bar height also typically increased with distance offshore and ranged from 0·03 to 0·61 m. A grain size analysis of crest and trough sediment did not reveal any significant differences and the sediment was categorized as ‘fine sand’. A review of the literature data indicated that the Chesapeake Bay multiple bars possessed similar characteristics to those found in Gelding Bay (Baltic Sea); similarities in fetch, wave height and tidal range between the two bays may account for this finding. The surf-scaling parameter indicated that the multiple bar systems were extremely dissipative with regard to wave energy, and wave height appeared to be an important factor in controlling bar spacing and bar height. A multiple wave break point hypothesis was discussed as a possible mechanism for the formation of Chesapeake Bay multiple longshore bars, and limited observational evidence appeared to support such a mechanism.     

Strain localization in sand: an overview of the experimental results obtained in Grenoble using stereophotogrammetry

Experimental results are presented from the extensive program of drained plane strain compression tests on sand carried out in Grenoble over the last two decades. Systematic analysis of photographs of the deforming specimen allowed for measuring deformations and determining strain fields throughout the test, that is: prior to, at, and after the onset of strain localization. The principles, details and accuracy of the procedure are described, as well as its suitability to properly depict the patterns of deformation. Findings concerning the occurrence and progression of strain localization are discussed. The issues of shear band orientation and thickness are addressed, as well as temporary and persistent complex localization patterns, and the volumetric behaviour inside a band after its formation. The influence of such variables as initial state of the sand (effective stress and relative density), specimen size and slenderness, as well as grain size, is discussed. Copyright © 2004 John Wiley & Sons, Ltd     

Petrogenesis of andalusite–kyanite–sillimanite veins and host rocks, Sanandaj-Sirjan metamorphic belt, Hamadan, Iran

Quartz‐rich veins in metapelitic schists of the Sanandaj‐Sirjan belt, Hamadan region, Iran, commonly contain two Al₂SiO₅ polymorphs, and, more rarely, three coexisting Al₂SiO₅ polymorphs. In most andalusite and sillimanite schists, the types of polymorphs in veins correlate with Al₂SiO₅ polymorph(s) in the host rocks, although vein polymorphs are texturally and compositionally distinct from those in adjacent host rocks; e.g. vein andalusite is enriched in Fe₂O₃ relative to host rock andalusite. Low‐grade rocks contain andalusite + quartz veins, medium‐grade rocks contain andalusite + sillimanite + quartz ± plagioclase veins, and high‐grade rocks contain sillimanite + quartz + plagioclase veins/leucosomes. Although most andalusite and sillimanite‐bearing veins occur in host rocks that also contain Al₂SiO₅, kyanite‐quartz veins crosscut rocks that lack Al₂SiO₅ (e.g. staurolite schist, granite). A quartz vein containing andalusite + kyanite + sillimanite + staurolite + muscovite occurs in andalusite–sillimanite host rocks. Textural relationships in this vein indicate the crystallization sequence andalusite to kyanite to sillimanite. This crystallization sequence conflicts with the observation that kyanite‐quartz veins post‐date andalusite–sillimanite veins and at least one intrusive phase of a granite that produced a low‐pressure–high‐temperature contact aureole; these relationships imply a sequence of andalusite to sillimanite to kyanite. Varying crystallization sequences for rocks in a largely coherent metamorphic belt can be explained by P–T paths of different rocks passing near (slightly above, slightly below) the Al₂SiO₅ triple point, and by overprinting of multiple metamorphic events in a terrane that evolved from a continental arc to a collisional orogen.     

中国海岸风成沙ESR测年的研究

介绍ＥＳＲ测年的基本原理，并讨论风成沙Ｇｅ心测年的可行性、风成沙Ｅ＇心的特征、测年误差及可靠性等问题。１９９２－１９９３年在渤、黄、东、南海沿岸采集的１００余个风成沙样品ＥＳＲ测年实验表明，绝大部分海岸风成沙的年龄为１－７万年。     

Short-term beach–dune sand budgets on the north sea coast of France: Sand supply from shoreface to dunes, and the role of wind and fetch

Three experimental plots, covering the transition from the upper beach to the dune, on the North Sea coast of France were monitored at various intervals over a period of 18–24 months via high resolution terrain surveys in order to determine inter-site sand budget variability, as well as patterns and processes involved in sand exchanges between the upper beach and dune. The wind regime consists of a fairly balanced mix of moderate (80% of winds are below 8 m/s) onshore, offshore and shore-parallel winds. Sustained dune accretion over several years depends on the periodic local onshore welding of shoreface tidal banks that have developed in the storm- and tide-dominated setting of the southern North Sea. The only site where this has occurred in the recent past is Calais, where bank welding has created a wide accreting upper beach sand flat. At this site, significant sand supply from the subtidal sand bank reservoir to the upper beach flat occurred only once over the 18-month survey following a major storm. The bulk of the sand deposited over this large flat is not directly integrated into the adjacent embryo dunes by onshore winds but is progressively reworked in situ into developing dunes or transported alongshore by the balanced wind regime, thus resulting in alongshore stretching of the embryo dune system. The Leffrinckoucke site near Belgium shows moderate beach–dune mobility and accretion, while the Wissant site exhibits significant upper beach bedform mobility controlled by strong longshore currents that result in large beach budget fluctuations with little net budget change, to the detriment of the adjacent dunes. Accretion at these two sites, which are representative of the rest of the North Sea coast of France, is presently constrained by the absence of a shore-attached sand bank supply reservoir, while upper beach–dune sand exchanges are further limited by the narrow wave-affected upper beach, the intertidal morphology of bars and troughs which segments the aeolian fetch, and the moderate wind energy conditions. The balanced wind regime limits net sand mobilisation in favour of either the beach or the dune, and may explain the relatively narrow longshore morphology of the dune ridges bounding this coast.     

Slump-initiated and controlled syndepositional sandstone remobilization: an example from the Namurian of County Clare, Ireland

Remobilization of sandstones can dramatically reconfigure original depositional geometries and results in very unusually shaped sandstones, which resemble little, if any, of the original geometry. A number of deformational sandstone bodies, dykes and volcanoes from the upper part of the Carboniferous Ross Formation are described, which offer the opportunity to examine a suite of field-scale reconfigured sandstones. These structures are located in close proximity to the Ross Slide, which outcrops along a 2-km section on the northern coast of the Loop Head Peninsula, County Clare, Ireland. Dome- and ridge-shaped deformational sandstone bodies, dykes and volcanoes are interpreted to be the product of remobilization of a turbiditic sandstone. Liquification and remobilization were triggered by translation, cessation and loading of the underlying turbiditic sandstone by the Ross Slide. Deformational sand body, dyke and volcano development occurred in an asynchronous fashion with deformational sand bodies formed during slump translation. Sand dykes and volcanoes developed after the cessation of slump movement. During slump translation, the minimum principal stress (σ₃) was orientated vertically and the slump behaved in a `ductile' manner. After slump arrest, the minimum principal stress was oriented horizontally, and the unit regained shear strength to behave in a `brittle' manner. The relative change in rheological states with changing applied shear stress is indicative of thixotropic-like behaviour within the slump mass. Ridge-shaped deformational sand bodies are aligned parallel to slump folds, and their morphology is inferred to be controlled by compressional slump deformation associated with heterogeneous cessation of slump movement that was initiated by frontal arrest of the translating mass.     

某地平板玻璃原料用石英砂的提纯研究

某地石英矿砂通过磁选分离法、稀酸浸泡法处理后，矿砂不同程度地降低了铁、铝、钙镁的含量；采用磁选分离 稀酸浸泡法联合处理后，使该地石英砂的化学成分达到了优质的生产平板玻璃用硅质原料的国家标准。     

论桩基施工中流砂现象处理

地下水流动对土体产生渗透力；当渗透力大于土体的抗剪强度，土体破坏，也就是当施工造成地下水水力坡度超过砂层的临界水力坡度即产生流砂现象．运用水文地质工程地质学方面的原理其处理方法有两类：—是莫尔一库仑法：即c法和φ法；二是临界水力坡度法(Ic法)．     

Determination of silica sand stiffness

Site investigation and evaluation of properties of soil or rock are important aspects of geotechnical design. Determination of the ground stiffness is one of the important parameters in geotechnical engineering. Since the measurement of shear modulus is very sensitive to soil disturbance, especially for sand, determination of the stiffness of soil in the field is more reliable than in laboratory tests on sampled specimens. Measurement of shear modulus is one of the most common applications of self-boring pressuremeter testing. As an in situ device, the pressuremeter provides a unique method for assessing directly the in situ shear modulus of a soil. This paper describes a laboratory study of silica sand stiffness, which varies with stress level and strain amplitude. The results show that the elastic shear modulus value is mainly dependent on the value of the mean effective stress and relative density.     

粘粒含量对南京粉细砂液化影响的试验研究

南京粉细砂是一种以片状颗粒成分为主的粉细砂，与通常的圆形颗粒石英砂有一定区别，片状颗粒成分使得南京粉细砂具有各向异性的性质。通过对不同粘粒含量的南京粉细砂进行液化试验，分析其试验结果发现：对于粘粒含量ρc＝5％、10％和15％三种情况，在均压固结情况下，当南京粉细砂达到初始液化时，采用变形标准和孔压标准是一致的；而偏压固结时，只能采用变形标准作为南京粉细砂达到初始液化的标准，此时振动孔压仅达到围压的50％-70％。粘粒含量对南京粉细砂的抗液化强度影响很大，随粘粒含量增加，在不同固结比时，其抗液化强度并不是单调变化，而是在粘粒含量ρc＝10％左右处于一个低谷，其抗液化强度最低。