Strain softening of K0-consolidated Changi sand under plane-strain conditions

Experimental results are presented in this paper to study the strain softening behaviour of a marine dredged sand under plane-strain conditions. K₀ consolidated drained and undrained tests were conducted using a new plane-strain apparatus to characterize the strain softening behaviour of the sand under plane-strain conditions. For medium dense specimens, strain softening and shear bands were observed to occur under both drained and undrained conditions. For very loose specimens, no shear bands were observed and critical states were reached within the homogeneous deformation region in both drained and undrained tests. Strain softening was observed to occur at small strain for very loose specimens under undrained conditions. Two types of strain softening, the homogenous softening and banding softening, were identified and the conditions for strain softening were established. The results obtained from this study were compared with the studies by Han and Vardoulakis (Géotechnique 41(1):49–78, 1991), Finno et al. (J Geotech Eng ASCE 122(6):462–473, 1996, Géotechnique 47(1):149–165, 1997) and Mokni and Desrues (Mech Cohes-Frict Mat 4:419–441, 1998).     

Significance of infiltrated clays within the Lower Permian Yellow Sands of north-east England

The Permian Yellow Sands are preserved as nine aeolian ridges in north-east England. The sands are soft and friable and locally contain large amounts of interstitial detrital clays, which are interpreted as the product of early mechanical clay infiltration. Features within the sands considered to be due to mechanical clay infiltration include grain coatings, meniscus and geopetal fabrics. The infiltrated clays mask crystal nucleation sites on grain surfaces and often amalgamate into lenses or form continuous clay-rich layers. Calcite and quartz cement growth has consequently been limited and often confined to the coarser, generally clay-free horizons. The meniscus and geopetal fabrics were formed early during accretion of the dunes and helped to bind and stabilize the sediment, which restricted reworking during the Zechstein transgression to the uppermost few decimeters.     

Computational study on the modification of a bounding surface plasticity model for sands

The accurate simulation of complex dynamic phenomena requires the availability of advanced constitutive models capable of simulating a wide range of features of soil behaviour under cyclic loading. One possible strategy is to improve the capabilities of existing bounding surface plasticity models, as this framework is characterised by its modularity and flexibility. As a result, specific components of the formulation of this type of model may be adjusted to improve the reproduction of any aspect of soil behaviour deemed essential to the problem being analysed. In this paper, a series of computational studies are performed in order to establish the impact of expanding a bounding surface plasticity model for sands on its modelling capabilities and to suggest ways of mitigating the associated increase in complexity. Changes to three distinct aspects of the selected constitutive model are examined: the shape of the Critical State Line in p′ − e space, the expression used for calculating the hardening modulus and the form of the yield surface. It is shown that the introduced changes have the potential to increase significantly the ability to control how certain aspects of soil response, such as degradation of stiffness and flow liquefaction with limited deformation, are reproduced by the model. Moreover, this paper presents a systematic approach to the expansion of this type of constitutive model, establishing how alterations to the formulation of a model may be assessed in terms of improved accuracy and potential benefits.     

A note on the measurement of travel times using bender and extender elements

By using the bender and extender elements tests, the travel times of the shear (S) and the primary (P) waves were measured for dry sand samples at different relative densities and effective confining pressures. Three methods of interpretations, namely, (i) the first time of arrival, (ii) the first peak to peak, and (iii) the cross-correlation method, were employed. All the methods provide almost a unique answer associated with the P-wave measurements. On contrary, a difference was noted in the arrival times obtained from the different methods for the S-wave due to the near field effect. The resonant column tests in the torsional mode were also performed to check indirectly the travel time of the shear wave. The study reveals that as compared to the S-wave, it is more reliable to depend on the arrival times’ measurement for the P-wave.     

An experimental study of the liquefaction strength of silty sands in terms of the state parameter

An elaborate program of monotonic and cyclic triaxial laboratory tests on mixtures of sand and silt with fines content 0%, 15% and 25% was performed to investigate the effect of density, consolidation stress and non-plastic fines on the liquefaction strength. The monotonic tests illustrated that the critical state lines of all mixtures do not cross each other, and are, approximately, parallel to each other. The results of the cyclic tests illustrated that the relationship between the cyclic strength and the state parameter does not depend on the consolidation stress, the soil density and the silt content. Analysis in terms of the state parameter showed that: (i) as the consolidation stress increases, the cyclic strength decreases and this effect is more pronounced as the specimens become denser, especially as the fines content increases and (ii) the cyclic strength decreases as the fines content increases and this effect is more pronounced as the specimens become denser.     

离散元微观参数对砂土宏观参数的影响

采用离散元商业软件PFC2D对密砂和松砂试样共进行了66组双轴压缩试验,试验中改变颗粒接触刚度和粒间摩擦系数以探究离散元微观参数对试样宏观参数(弹性模量和内摩擦角)的影响,其中颗粒法向刚度变化范围为1.5×108～1.5×109N.m-1,粒间摩擦系数变化范围为0.1～0.7 N.m-1。结果表明:颗粒接触刚度对弹性模量有一定程度影响且对密样影响程度大于松样,而对内摩擦角基本无影响;粒间摩擦系数对试样弹性模量有明显影响且对松样的影响程度更大,对密样和松样的内摩擦角都有非常显著的影响。     

青岛文昌鱼的实验室培育──饵料和沙对幼虫成活的影响

于1991年6月-1992年12月对青岛文昌鱼进行室内培育研究。结果表明：1．沙是青岛文昌鱼幼虫生长发育必需的，但在实验室条件下，细沙比全沙和粗沙更有利于其生存。2．就单胞藻而言，等鞭金藻是青岛文昌鱼幼虫生长和变态较理想的饵料。     

Measured and calculated spudcan penetration profiles for case histories in sand-over-clay

This paper reports five case histories of jack-up rig installation in layered soil profiles where a dominate feature was a stronger sand layer overlaying a weaker clay layer. In all cases a relatively continuous load-penetration profile was measured during installation of each of the three spudcan foundations. Summary site-investigation data is provided and consisted of mainly torvane, minature vane, unconsolidated undrained triaxial and pocket penetrometer tests for determining undrained shear strength of the clays and blow counts for deriving the relative density of sand. A statistical averaging method recommended in the InSafeJIP guidelines was used to provide the best fit of the undrained shear strength profile in the clay as this then allowed for spudcan load-penetration profiles to be estimated without introduction of user interpretation or bias. Sand properties were taken as provided in the original site-investigation report. Comparisons between load-penetration profiles calculated using the industry-standard ISO guideline, more recently proposed mechanism-based calculation method and three-dimensional large deformation finite element simulations are made with the measured data, leading to valuable insights for practitioners for estimating behaviour of jack-up installations in problematic sand-over-clay soil profiles.     

Cyclic liquefaction screening of sand with non-plastic fines:Critical state approach

There have been significant advances in the application of critical state,CS,in liquefaction potential assessment.This was done by comparing state parameter,j with estimated characteristic cyclic stress ratio,CSR due to an earthquake.A cyclic resistance ratio,CRR curve,which can be determined from cyclic liquefaction tests,separates historical liquefied and non-liquefied data points(j,CSR).On the other hand,the concepts of equivalent granular state parameter,j*,which was developed for sands with fines,can be used in lieu j to provide a unifying framework for characterizing the undrained response of sands with non/low plasticity fines,irrespective of fines content(fc).The present work combines these two propositions,and by merely substituting j*for j into the aforementioned CS approach to capture the influence of fc.A series of static and cyclic triaxial tests were conducted,separately and independently of the concept of j*,for sand with up to fc of 30%.The clean sand was collected from Sabarmati river belt at Ahmedabad city in India which was severely affected during the Bhuj earthquake,2001.The experimental data gave a single relation for CRR and j*which was then used to assess liquefaction potential for a SPT based case study,where fc varies along the depth.The prediction matched with the field observation.     

The effect of carbonaceous fines on the cyclic resistance of poorly graded sands

The potential damage to man-made structures associated with earthquake-induced liquefaction has been demonstrated in catastrophic fashion over the past 40–50 years. The phenomenon of liquefaction of relatively clean, poorly graded, sands is well understood. However, the same cannot be said for cases when fine-grained materials are present within the sand matrix. A resolution of what appears in some reported studies as conflicting observations related to the effect of fines on cyclic resistance is of concern, particularly for land reclamation projects and sea fills where the material source is variable and may contain significant levels of fines. The nature of the fines themselves may have a measurable effect on the matrix behavior. The work presented herein explores the effect of silt and clay-size carbonaceous fines on the liquefaction susceptibility of sand. The choice of fines was guided by the conditions associated with the Lebanon coastal reclamation projects, where limestone/marlstone quarry source materials are dominant. The results obtained confirm the significant effect of fines on the cyclic resistance. They also confirm the existence of a limit fines content and a plasticity index threshold and establish their effect on observed behavior.