Modelling the effect of changing precipitation inputs on deep soil water utilization

Forests in the Southeastern United States are predicted to experience future changes in seasonal patterns of precipitation inputs as well as more variable precipitation events. These climate change‐induced alterations could increase drought and lower soil water availability. Drought could alter rooting patterns and increase the importance of deep roots that access subsurface water resources. To address plant response to drought in both deep rooting and soil water utilization as well as soil drainage, we utilize a throughfall reduction experiment in a loblolly pine plantation of the Southeastern United States to calibrate and validate a hydrological model. The model was accurately calibrated against field measured soil moisture data under ambient rainfall and validated using 30% throughfall reduction data. Using this model, we then tested these scenarios: (a) evenly reduced precipitation; (b) less precipitation in summer, more in winter; (c) same total amount of precipitation with less frequent but heavier storms; and (d) shallower rooting depth under the above 3 scenarios. When less precipitation was received, drainage decreased proportionally much faster than evapotranspiration implying plants will acquire water first to the detriment of drainage. When precipitation was reduced by more than 30%, plants relied on stored soil water to satisfy evapotranspiration suggesting 30% may be a threshold that if sustained over the long term would deplete plant available soil water. Under the third scenario, evapotranspiration and drainage decreased, whereas surface run‐off increased. Changes in root biomass measured before and 4 years after the throughfall reduction experiment were not detected among treatments. Model simulations, however, indicated gains in evapotranspiration with deeper roots under evenly reduced precipitation and seasonal precipitation redistribution scenarios but not when precipitation frequency was adjusted. Deep soil and deep rooting can provide an important buffer capacity when precipitation alone cannot satisfy the evapotranspirational demand of forests. How this buffering capacity will persist in the face of changing precipitation inputs, however, will depend less on seasonal redistribution than on the magnitude of reductions and changes in rainfall frequency.     

Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.     

Effects of the geometry of two‐dimensional fractures on their hydraulic aperture and on the validity of the local cubic law

Flow through rough fractures is investigated numerically in order to assess the validity of the local cubic law for different fracture geometries. Two‐dimensional channels with sinusoidal walls having different geometrical properties defined by the aperture, the amplitude, and the wavelength of the walls' corrugations, the corrugations asymmetry, and the phase shift between the two walls are considered to represent different fracture geometries. First, it is analytically shown that the hydraulic aperture clearly deviates from the mean aperture when the walls' roughness, the phase shift, and/or the asymmetry between the fracture walls are relatively high. The continuity and the Navier–Stokes equations are then solved by means of the finite element method and the numerical solutions compared to the theoretical predictions of the local cubic law. Reynolds numbers ranging from 0.066 to 66.66 are investigated so as to focus more particularly on the effect of flow inertial effects on the validity of the local cubic law. For low Reynolds number, typically less than 15, the local cubic law properly describes the fracture flow, especially when the fracture walls have small corrugation amplitudes. For Reynolds numbers higher than 15, the local cubic law is valid under the conditions that the fracture presents a low aspect ratio, small corrugation amplitudes, and a moderate phase lag between its walls.     

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.     

Bacterial productivity in the Prydz Bay and its adjacent waters,Antarctic

1　IntroductionBacteriaandtheiractivitiesplayanimportantroleintheelementalbiogeochemicalcyclesandenergytransformingintheocean (Zhenetal.1 997) .DortchandPackard(1 989) proposedthatfoodwebsintheeutrophicwatersaredominatedbythebiomassofprimaryproducerswhilefoodwebsintheoligotrophicwatersaredominatedbythebiomassofmicrobes.Heterotrophicbacteriahadbeenshowntoplayanimportantroleinthedecompositionoflarge ,rapidlysinkingorganicparticleswithinandbelowtheeuphot iczone ,andfurthertoaffecttheelementaldyn…     

双极化天气雷达方程

在回转椭球状降水粒子的假设下求出了降水粒子的散射截面，并且考虑了粒子轴线铅垂和随机取向两种重要的典型情况；推导了双极化雷达的回波方程以及降雨量公式。该方程除包含降水粒子的信息外，关于雷达与降水粒子间的几何关系都以雷达天线仰角及雷达与降水粒子间的距离表示，同时还考虑了地球的球面效应和大气折射效应。由于采用了并矢方法，使推导简捷明了     

地壳对海洋潮汐的响应

应用三维动态有限元方法研究了中国北部地区的地壳对邻近的渤海与黄海海平面变化的响应。虽然此应力场过于微弱不足以引发地震，但发现应力集中的位置及应力场变化较大的位置恰好与某些现代地震的震中一致。这一结果表明研究地壳对广泛分布的载荷的响应对研究区域地震构造是有帮助的。     

济宁市嘉祥县石灰岩矿山地质环境评价与治理

在对嘉祥县石灰岩矿进行地质灾害危险性评估、矿山环境地质问题评价的基础上,建立了一套评价体系,其中地质灾害危险性评估分为2个评价指标,矿山环境地质问题评价分为2种要素3个指标,同时将矿山恢复治理难易程度也作为一个评价因子。评价过程中对各指标危害性大、中、小程度均单独赋值,然后将各指标的分值进行叠加,确定出矿山环境地质问题的等级,将概划出的13个评价单元分为极差、差、一般3个区。提出了强化矿山管理、植树造林、科学避让、修建拦水坝等保护与治理措施及建议。     

浅谈项目投资失败的原因及对策

地勘单位在向企业化经营转变的过程中 ,投资兴办了许多企业 ,但不少项目以失败告终。文章分析探讨了失败的原因 ,并提出相应的对策     

广西老厂铅锌矿床地质特征及其成因探讨

本文是在专题研究基础上,探讨广西老厂铅锌矿床地质特征和矿床成因。该矿床位于海洋山复式背斜南段的老厂穹窿构造核部,铅锌矿化受构造、地层和岩性控制。矿体呈脉状,产于NE向组张扭性断裂构造中;围岩为寒武系白云岩,板岩、砂岩;矿石类型以锌为主,矿物成分简单,以闪锌矿、方铅矿与石英、白云石为主,具充填、交代矿石结构、构造,矿石平均品位含Zn9.94%、Pb1.50%;围岩蚀变主要为硅化、绢云母化和碳酸盐化。据地层岩石元素丰度值、稀土元素配分和稳定同位素数据、资料,探讨了成矿物质来源于围岩,热液主要来自大气降水。因此,认为本矿床实属产于寒武系轻变质岩中的层控矿型大气降水热液铅锌矿床。