Dissolution and depletion of ferromagnesian minerals from Holocene tephra layers in an acid bog,New Zealand,and implications for tephra correlation

This study examines the depletion of ferromagnesian silicate minerals from a sequence of thin, distal, mainly rhyolitic tephra layers of Holocene age preserved in an acid peat bog (Kopouatai), North Island, New Zealand. The rate of such depletion has been fast, as indicated by the complete loss of biotite from one tephra layer (Kaharoa Tephra), in which it is normally dominant, in only ca. 770 yr. Chemical dissolution is advocated as the likely cause for the depletion, with amphiboles and other mineral grains commonly showing etch pits, microcaves, and other characteristic surface solution features. Theoretical thermodynamic and kinetic models show a marked increase in the rate of dissolution of all ferromagnesian minerals under conditions of low pH (< 4), but that where silica concentrations in solution are high the relative proportions of minerals remaining are unaffected. However, where concentrations of dissolved silica are low, as in most bog environments, the relative proportions of ferromagnesian minerals are affected as well as absolute amounts being decreased. Amphiboles are depleted relative to pyroxenes, consistent with kinetic studies. The results show that the identification and correlation of tephras on the basis of relative abundances of ferromagnesian minerals alone may be unreliable, and emphasise the need to use multiple criteria in such studies.     

广西岩溶区金属硫化物矿床风化与元素表生迁移特征

对广西岩溶区三个铅锌硫化物矿床风化带观测结果表明，中低山岩溶区硫化物矿床具有更强烈的风化淋滤作用，但次生晕面积较小；岩溶平原区硫化物矿床风化与元素表生迁移特征较相似于非岩溶区的情况，表现在可产生较宽的ｐＨ偏低带和较大面积的次生晕     

Microbial release of potassium from K-bearing minerals by thermophilic fungus Aspergillus fumigatus

A strain of thermophilic fungus Aspergillus fumigatus was cultured with K-bearing minerals to determine if microbe-mineral interactions enhance the release of mineralic potassium. Experiments were carried out in two settings, one with the mineral grains and the fungal cells in direct contact, and the other employing a membrane (pore size 0.22 μm) to separate the two. Measurements over a period of 30 days showed that, irrespective of the experimental setup, the concentration of free K in the culture was drastically higher than those in any of the control experiments where no living organism was present. Moreover, the occurrence of mineral-cell physical contact enhanced potassium release by an additional factor of 3 to 4 in comparison to the separation experiments. For contact experiments, Electron Probe Microanalysis revealed the formation of mycelium-mineral aggregates, and Atomic Force Microscopy imaging further indicated the possible ingestion of mineral particles by the fungus cells. Contrasting to what was observed and expected in control experiments, the potassium solubilization rate showed a positive dependence upon pH when fungi and minerals were mixed directly, and exhibited no correlations with solution acidity if cell-rock contact was restrained. These results appear to suggest that A. fumigatus promoted potassium release by means of at least three likely routes, one through the complexation of soluble organic ligands, another appealing to the immobile biopolymers such as the insoluble components of secretion, and the third related to the mechanical forces in association with the direct physical contact between cells and mineral particles.     

An Attempt to Predict the Failure Time of Abandoned Mine Pillars

Summary  Left in place pillars of abandoned mines are subject to weathering (e.g action of water, bacteria) that degrades their mechanical strength and eventually leads to collapse. A simple weathering model is proposed, that is governed by two parameters: the rate of progression of weathered front and the rate of degradation of the compressive strength with time. Both plane strain and axisymmetric analyses are performed and closed form solutions of the variation with time of the bearing capacity of the pillar are given. Experimental data of the tests conducted on gypsum and anhydrite specimens attacked by water are presented. It is shown that in order to fit the experimental data a third parameter must be introduced. New closed form solutions are given and the data are used for estimating the time to failure of abandoned gypsum mines in Northern Italy. Authors’ address: Dr. Riccardo Castellanza, Research Assistant, Department of Structural Engineering, Milan University of Technology (Politecnico), Piazza Leonardo da Vinci 32, 20133 Milan, Italy     

水面皮层破坏-复原过程的实验室模拟研究

依据水面红外发射和红外遥感测温原理，采用HDG－高灵敏度红外测温仪和常规测量仪器相结合的方法，在实验室空气稳定条件下，模拟测得了水面皮层破坏－复原（重建）的热力过程和气－水温差对水面皮层复原过程的影响，获得了大量的测量数据。数据分析表明，当气－水温差从3．0℃变为11．5℃时，水面皮层破坏可导致皮温增量从气－水温差3．0℃时的0．15℃变到11．5℃时的0．45℃，并发现恢复时间与气－水温差呈负线性关系。     

The dimensions of sand ripples in full-scale oscillatory flows

New large-scale experiments have been carried out in two oscillatory flow tunnels to study ripple regime sand suspension and net sand transport processes in full-scale oscillatory flows. The paper focuses on ripple dimensions and the new data are combined with existing data to make a large dataset of ripple heights and lengths for flows with field-scale amplitudes and periods. A feature of the new experiments is a focus on the effect of flow irregularity. The combined dataset is analysed to examine the range of hydraulic conditions under which oscillatory flow ripples occur, to examine the effects of flow irregularity and ripple three-dimensionality on ripple dimensions and to test and improve existing methods for predicting ripple dimensions.The following are the main conclusions. (1) The highest velocities in a flow time-series play an important role in determining the type of bedform occurring in oscillatory flow. Bedform regime is well characterised by mobility number based on maximum velocity in the case of regular flow and based on the mean of the highest one tenth peak velocities in the case of irregular flow. (2) For field-scale flows, sand size is the primary factor determining whether equilibrium ripples will be 2D or 3D. 2D ripples occur when the sand D₅₀ ≥ 0.30 mm and 3D ripples occur when D₅₀ ≤ 0.22 mm (except when the flow orbital diameter is low). (3) Ripple type (2D or 3D) is the same for regular and irregular flows and ripple dimensions produced by equivalent regular and irregular flows follow a similar functional dependence on mobility number, with mobility number based on maximum velocity in the case of regular flow and based on the mean of the highest one tenth velocities in the case of irregular flow. For much of the ripple regime, ripple dimensions have weak dependency on mobility number and ripple dimensions are similar for regular and irregular flows with the same flow orbital amplitude. However, differences in ripples produced by equivalent regular and irregular flows become significant at the high mobility end of the ripple regime. (4) Ripple dimensions predicted using the Wiberg and Harris formulae are in poor agreement with measured ripple dimensions from the large-scale experiments. Predictions based on the Mogridge et al. and the Nielsen formulae show better overall agreement with the data but also show systematic differences in cases of 3D ripples and ripples generated by irregular flows. (5) Based on the combined large-scale data, modifications to the Nielsen ripple dimension equations are proposed for the heights and lengths of 2D ripples. The same equations apply to regular and irregular flows, but with mobility number appropriately defined. 3D ripples are generally smaller than 2D ripples and estimates of 3D ripple height and length may be obtained by applying multipliers of 0.55 and 0.73 respectively to the 2D formulae. The proposed modified Nielsen formulae provide an improved fit to the large-scale data, accounting for flow irregularity and ripple three-dimensionality.     

Wave reflection from partially perforated-wall caisson breakwater

In 1995, Suh and Park developed a numerical model that computes the reflection of regular waves from a fully perforated-wall caisson breakwater. This paper describes how to apply this model to a partially perforated-wall caisson and irregular waves. To examine the performance of the model, existing experimental data are used for regular waves, while a laboratory experiment is conducted in this study for irregular waves. The numerical model based on a linear wave theory tends to over-predict the reflection coefficient of regular waves as the wave nonlinearity increases, but such an over-prediction is not observed in the case of irregular waves. For both regular and irregular waves, the numerical model slightly over- and under-predicts the reflection coefficients at larger and smaller values, respectively, because the model neglects the evanescent waves near the breakwater.     

Effect of Bacillus mucilaginosus on weathering of phosphorite and a preliminary analysis of bacterial proteins

The authors investigated the effect of Bacillus mucilaginosus on weathering of phosphorite. Analysis of different proteins was of significance in exploring the molecular biological mechanism in the bacterial weathering process. The concrete methods are described as follows： Mineral powder was put into liquid culture medium and B. mucilaginosus was incubated in the medium. The control （group） had no mineral powder in the medium. The treatments and controls were cultured simultaneously under the same condition. In a few days, the supernatant was filtrated, the main cations （Ca^2＋, Mg^2＋, Na^＋, Mn^2＋, Al^3＋, Fe^3＋, K^＋） were measured by ICP-OES, and the contents of water soluble phosphorus （Pws） and silicon （Siws） were determined by colorimetry. The residual solid was weighed on the filter paper, followed by digestion with concentrated HNO3. The concentrations of the main cations and Pws, Siws in the digest liquid were measured by using the method mentioned above. After the supernatant was centrifuged, the precipitation was used to analyze the protein differences between the treatment groups and the control groups by 2-dimentional gel electrophoresis （2-DE）. The experimental results showed that apatite and quartz were partially weathered, but kaolinite was dissolved completely. The population of bacteria increased when mineral powder was added in the liquid medium. Software analysis and comparison of the 2-DE pictures of bacterial proteins revealed 1134 visible protein spots in the treatment group, and 729 visible protein spots in the control group. To compare the bacterial protein expression contents of the treatment group with those of the control group, there were 496 different protein spots, including 214 protein spots which indicated that the protein contents increased, 75 protein spots were indicative of a decrease, and 207 proteins were newly synthesized. It is proposed that the increased bacterial contents may be related to some protein expression and activation after the     

Lake bank filtration at Nainital,India: water-quality evaluation

There are different water-supply schemes in Uttarakhand, India to tap the water from streams, rivers and lakes. At Nainital, seven tube-wells (depths 22.6–36.7 m), located at a distance of <100 m from the lake, are being used to abstract (1) lake water after passage through the soil and (2) subsurface water/groundwater flowing towards the lake. Water samples from the lake and tube-wells were analyzed in monsoon and non-monsoon periods from 1997 to 2006. Total dissolved solids, EC, alkalinity and hardness were found to be marginally greater in tube-well waters. The difference in hydrochemistry of tube-well water was mainly due to variation in flow regimes during monsoon and non-monsoon periods. Results clearly indicate that lake water as such is not potable as it contains unacceptable levels of organic matter in terms of COD (~44 mg/L), coliforms (~15.6 × 10⁴ MPN/100 mL) and nutrients. Coliform bacteria and COD have not been detected in any of the tube-well water samples over the years. Lake water, treated by sand filters did not conform to drinking water standards. These investigations have led to the closure of the treatment facility and installation of two tube-wells in addition to the existing five tube-wells.

---

Résumé  Il existe divers projets d’alimentation en eau dans l’état d’Uttarakhand, Inde, afin de capter l’eau de ruisseaux, de rivières et de lacs. A Nainital, sept puits tubés (profondeur de 22.6–36.7 m), situés à une distance < à 100 m du lac, sont utilisés pour prélever (1) de l’eau du lac après transit à travers le sol et (2) de l’eau de sub-surface/eau souterraine s’écoulant vers le lac. Des échantillons d’eau du lac et des puits tubés ont été analysés en périodes de mousson et de celles sans mousson 1997 à 2006. Résidu sec, C.E., alcalinité et dureté ont été trouvés marginalement supérieurs dans l’eau des puits tubés. La différence d’hydrochimie de l’eau des puits tubés était surtout due à la variation des régimes d’écoulement pendant les périodes de mousson et de celles sans mousson. Les résultats indiquent clairement que l’eau du lac en tant que telle n’est pas potable car elle contient des teneurs inacceptables de matière organique en termes de COD (~44 mg/L), de coliformes (~15.6 × 10⁴ MPN/100 mL) et d’éléments nutritifs. Des bactéries coliformes et du COD n’ont été détectés dans aucun des échantillons d’eau de puits tubés au fil des années. L’eau du lac traitée par des filtres à sable ne se conformait pas aux normes de l’eau potable. Ces recherches ont conduit à la fermeture de l’installation de traitement et à l’implantation de deux puits tubés en plus des cinq puits existants.

---

Resumen  En el estado de Uttarakhand, India, existen diferentes esquemas de abastecimiento de agua que explotan agua de arroyos, ríos y lagos. En Nainital, siete pozos (profundidades entre 22.6–36.7 m), ubicados a una distancia de <100 m del lago, se usan para extraer (1) agua del lago luego de su pasaje a través del suelo y (2) agua superficial y subterránea que fluye hacia el lago. En períodos de monzón y de no monzón de 1997 a 2006 se han analizado muestras de agua del lago y de las captaciones. Se halló que el agua de los pozos es ligeramente mayor en términos del total de sólidos disueltos, la conductividad eléctrica, la alcalinidad y la dureza. La diferencia en la hidroquímica del agua de las perforaciones se debe principalmente a la variación de los regímenes de flujo durante los períodos de monzón y de no monzón. Los resultados claramente indican que el agua del lago no es potable por su contenido inaceptable de materia orgánica medida como demanda de carbono orgánico/oxígeno –DCO- (~44 mg/L), coliformes (~15.6 × 10⁴ NMP/100 mL) y nutrientes. En el período, no se han detectado bacterias coliformes ni DCO en las muestras de agua de las captaciones. El agua del lago, tratada con filtros de arena, no conformó los estándares de agua para bebida. Estas investigaciones han demostrado la necesidad de clausurar las instalaciones de tratamiento y la adición de dos captaciones a las cinco ya existentes.

     

中国南方离子吸附型稀土矿床成矿类型及其母岩控矿因素探讨

传统认为中国南方的离子吸附型稀土矿床可划分为以“足洞式”为代表的重稀土型和以“河岭式”(或“花山式”)为代表的轻稀土型两种矿化类型。然而，近年来发现的许多矿床(如清溪、寨背和馒头山等)的赋矿风化壳中出现了轻稀土矿与重稀土矿并存现象，表现出特殊的“上轻下重”双层矿体结构。这指示了除重稀土型和轻稀土型之外，还存在着轻重稀土共生型的过渡类型。本研究通过对三种不同成矿类型的若干典型矿床系统对比，指出成矿类型的多样性与母岩性质密切相关，尤其是母岩的稀土元素地球化学和稀土载体矿物属性是制约成矿类型变化的关键因素。统计数据表明，从重稀土型→轻重稀土共生型→轻稀土型，成矿母岩的全岩稀土总量变化不大(ΣREY: 200×10-6~450×10-6→200×10-6~500×10-6→200×10-6~800×10-6)，但轻重稀土配分值出现较显著的区间性差异(ΣLREE/ΣHREY: 02~1→1~5→2~10)。与之同时，母岩中能为离子相稀土提供物源且具有重稀土配分属性的稀土副矿物类型和数量明显减少，这与全岩稀土元素地球化学特征中重稀土分量占比的降低趋势也互相匹配。该结果指示，以往认为重稀土配分母岩形成重稀土矿床、轻稀土配分母岩形成轻稀土矿床的传统观点需要外延，即一部分具有低度轻稀土配分属性(1＜ΣLREE/ΣHREY＜5)且含有丰富易风化稀土副矿物的母岩还可能形成轻重稀土共生型矿床，该认识可为今后离子吸附型稀土矿床勘查工作提供新的找矿依据。