Metamorphism in Archaean greenstone belts: calculated fluid compositions and implications for gold mineralization

An inescapable consequence of the metamorphism of greenstone belt sequences is the release of a large volume of metamorphic fluid of low salinity with chemical characteristics controlled by the mineral assemblages involved in the devolatilization reactions. For mafic and ultramafic sequences, the composition of fluids released at upper greenschist to lower amphibolite facies conditions for the necessary relatively hot geotherm corresponds to those inferred for greenstone gold deposits (X_CO2= 0.2–0.3). This result follows from the calculation of mineral equilibria in the model system CaO–MgO–FeO–Al₂O₃–SiO₂–H₂O–CO₂, using a new, expanded, internally consistent dataset. Greenstone metamorphism cannot have involved much crustal over-thickening, because very shallow levels of greenstone belts are preserved. Such orogeny can be accounted for if compressive deformation of the crust is accompanied by thinning of the mantle lithosphere. In this case, the observed metamorphism, which was contemporaneous with deformation, is of the low-P high-T type. For this type of metamorphism, the metamorphic peak should have occurred earlier at deeper levels in the crust; i.e. the piezothermal array should be of the ‘deeper-earlier’type. However, at shallow crustal levels, the piezothermal array is likely to have been of ‘deeper-later’type, as a consequence of erosion. Thus, while the lower crust reached maximum temperatures, and partially melted to produce the observed granites, mid-crustal levels were releasing fluids prograde into shallow crustal levels that were already retrograde. We propose that these fluids are responsible for the gold mineralization. Thus, the contemporaneity of igneous activity and gold mineralization is a natural consequence of the thermal evolution, and does not mean that the mineralization has to be a consequence of igneous processes. Upward migration of metamorphic fluid, via appropriate structurally controlled pathways, will bring the fluid into contact with mineral assemblages that have equilibrated with a fluid with significantly lower X_CO2. These assemblages are therefore grossly out of equilibrium with the fluid. In the case of infiltrated metabasic rocks, intense carbonation and sulphidation is predicted. If, as seems reasonable, gold is mobilized by the fluid generated by devolatilization, then the combination of processes proposed, most of which are an inevitable consequence of the metamorphism, leads to the formation of greenstone gold deposits predominantly from metamorphic fluids.     

黑龙江省鸡西盆地南、北两带城子河组精细对比

鸡西盆地被平麻断裂分割成南、北两个条带,多数研究者将南带1煤之下的海相层叠伏于北带海相层或底砾岩之下,称为“城子河组下段”或“石河北组”。利用事件地层学的原理,分析盆地内城子河组早期盆地裂陷、海侵、火山喷发、聚煤等重大事件在地层精细对比方面的意义,甄别出了盆地中重大事件的地层记录．以等时层为基础建立对比框架。通过大量钻井资料追溯对比,认为盆地中坳陷部位的渴湖海湾沉积是南北两带的沉积过渡类型,根据微体古生物研究,南北两带海相层中的沟鞭藻类化石面貌基本一致,南北带的海相层应是同一层位,初步实现了盆地内南、北两个条带城子河组的精细对比,为恢复盆地古地理环境奠定了可靠的基础。     

Preservation/exhumation of ultrahigh-pressure subduction complexes

Ultrahigh-pressure (UHP) metamorphic terranes reflect subduction of continental crust to depths of 90–140 km in Phanerozoic contractional orogens. Rocks are intensely overprinted by lower pressure mineral assemblages; traces of relict UHP phases are preserved only under kinetically inhibiting circumstances. Most UHP complexes present in the upper crust are thin, imbricate sheets consisting chiefly of felsic units ± serpentinites; dense mafic and peridotitic rocks make up less than  10% of each exhumed subduction complex. Roundtrip prograde–retrograde P–T paths are completed in 10–20 Myr, and rates of ascent to mid-crustal levels approximate descent velocities. Late-stage domical uplifts typify many UHP complexes.

Sialic crust may be deeply subducted, reflecting profound underflow of an oceanic plate prior to collisional suturing. Exhumation involves decompression through the P–T stability fields of lower pressure metamorphic facies. Scattered UHP relics are retained in strong, refractory, watertight host minerals (e.g., zircon, pyroxene, garnet) typified by low rates of intracrystalline diffusion. Isolation of such inclusions from the recrystallizing rock matrix impedes back reaction. Thin-aspect ratio, ductile-deformed nappes are formed in the subduction zone; heat is conducted away from UHP complexes as they rise along the subduction channel. The low aggregate density of continental crust is much less than that of the mantle it displaces during underflow; its rapid ascent to mid-crustal levels is driven by buoyancy. Return to shallow levels does not require removal of the overlying mantle wedge. Late-stage underplating, structural contraction, tectonic aneurysms and/or plate shallowing convey mid-crustal UHP décollements surfaceward in domical uplifts where they are exposed by erosion. Unless these situations are mutually satisfied, UHP complexes are completely transformed to low-pressure assemblages, obliterating all evidence of profound subduction.     

Monitoring of Over Cutting Area and Lubrication Distribution in a Large Slurry Pipe Jacking Operation

Slurry pipe jacking was firmly established as a special method for the non-disruptive construction of the underground pipelines of sewage systems. Pipe jacking, in its traditional form, has occasionally been used for short railways, roads, rivers, and other projects. Basically the system involves the pushing or thrusting of concrete pipes into the ground by a number of jacks. In slurry pipe jacking, during the pushing process, mud slurry and lubricant are injected into the face and the over cutting area that is between the concrete pipes and the surrounding soil. Next, the slurry fills voids and the soil stabilizes due to the created slurry cake around the pipes. Fillings also reduce the jacking force or thrust during operation. When the drivage and pushing processes are finished, a mortar injection into the over cutting area is carried out in order to maintain permanent stability of the surrounding soil and the over cutting area. Successful lubrication around the pipes is extremely important in a large diameter slurry pipe jacking operation. Control of lubrication and gaps between pipes and soil can prevent hazards such as surface settlement and increases in thrust. Also, to find voids around the pipes after the jacking process, in order to inject mortar for permanent stabilizing, an investigation around the pipes is necessary. To meet these aims, this paper is concerned with the utilization of known methods such as the GPR (Ground Penetrating Radar) system and borehole camera to maintain control of the over cutting area and lubricant distribution around the pipes during a site investigation. From this point of view, experiments were carried out during a tunnel construction using one of the largest cases of slurry pipe jacking in Fujisawa city, Japan. The advantages and disadvantages of each system were clarified during the tests.     

Evolution from Oceanic Subduction to Continental Collision: a Case Study from the Northern Tibetan Plateau Based on Geochemical and Geochronological Data

Two apparently distinct, sub-parallel, paleo-subduction zonescan be recognized along the northern margin of the Tibetan Plateau:the North Qilian Suture Zone (oceanic-type) with ophioliticmélanges and high-pressure eclogites and blueschistsin the north, and the North Qaidam Belt (continental-type) inthe south, an ultrahigh-pressure (UHP) metamorphic terrane comprisingpelitic and granitic gneisses, eclogites and garnet peridotites.Eclogites from both belts have protoliths broadly similar tomid-ocean ridge basalts (MORB) or oceanic island basalts (OIB)in composition with overlapping metamorphic ages (480–440Ma, with weighted mean ages of 464 ± 6 Ma for North Qilianand 457 ± 7 Ma for North Qaidam), determined by zirconU–Pb sensitive high-resolution ion microprobe dating.Coesite-bearing zircon grains in pelitic gneisses from the NorthQaidam UHP Belt yield a peak metamorphic age of 423 ±6 Ma, 40 Myr younger than the age of eclogite formation, anda retrograde age of 403 ± 9 Ma. These data, combinedwith regional relationships, allow us to infer that these twoparallel belts may represent an evolutionary sequence from oceanicsubduction to continental collision, and continental underthrusting,to final exhumation. The Qilian–Qaidam Craton was probablya fragment of the Rodinia supercontinent with a passive marginand extended oceanic lithosphere in the north, which was subductedbeneath the North China Craton to depths >100 km at c. 423Ma and exhumed at c. 403 Ma (zircon rim ages in pelitic gneiss). KEY WORDS: HP and UHP rocks; subduction belts; zircon SHRIMP ages; Northern Tibetan Plateau     

三峡库区滑坡治理工程设计中推力荷载计算方法初探

随着三峡水利工程的逐步实施，淹没区移民及新城镇建设等人类工程活动的加剧，以滑坡为主的环境地质问题日益突出。本文从稳定系数、安全系数入手，对铁道、公路等部门常用的设计计算原理进行了研究，并由此类比分析研究了三峡区回水后或库水位正常运行条件下，滑坡治理工程设计计算方法。     

Topography as a major factor in the development of arcuate thrust belts: insights from sandbox experiments

We have used sandbox experiments to investigate and to illustrate the effects of topography upon the development of arcuate thrust belts. In experiments where a sand pack shortened and thickened in front of an advancing rectilinear piston, the geometry of the developing thrust wedge was highly sensitive to variations in surface topography. In the absence of erosion and sedimentation, the surface slope tended to become uniform, as predicted by the theory of critical taper. Under these conditions, the wedge propagated by sequential accretion of new thrust slices. In contrast, where erosion or sedimentation caused the topographic profile to become irregular, thrusts developed out of sequence. For example, erosion throughout a hinterland caused underlying thrusts to remain active and inhibited the development of new thrusts in the foreland. Where initial topography was irregular in plan view, accreting thrusts tended to be arcuate. They were convex towards the foreland, around an initially high area; concave towards the foreland, around an initially low area. Initial plateaux tended to behave rigidly, while arcuate thrust slices accreted to them. Thrust motions were radial with respect to each plateau. Within transfer zones to each side, fault blocks rotated about vertical axes and thrust motions were oblique-slip. At late stages of deformation, the surface slope of the thrust wedge tended towards a uniform value. Initial mountains of conical shape (representing volcanoes) also escaped deformation, except at depth, where they detached. Arcuate thrust slices accreted to front and back. Where a developing thrust wedge was subject to local incision, accreting thrust slices dipped towards surrounding areas of high topography, forming Vs across valleys.Arcuate structural patterns are to be found around the three highest plateaux on Earth (Tibet, Pamirs and Altiplano) and around the Tromen volcanic ridge in the Neuquén Basin of northern Patagonia. We infer that these areas behaved in quasi-rigid fashion, protected as they were by their high topography.     

Models of passive margin inversion: implications for the Rhenohercynian fold-and-thrust belt, Belgium and Germany

Positive tectonic inversion is related to the transmission of compressional stresses along a décollement into the foreland of an orogenic zone. This stress and strain concentration in regions remote from the main orogenic front is commonly related to the presence of pre-existing rheological heterogeneities such as normal syn-depositional faults. During inversion, these pre-existing normal faults are reactivated as reverse faults. Tectonic inversion in the Rhenohercynian fold-and-thrust belt during the Variscan Orogeny shows that inversion is likely synchronous with the onset of collision in the hinterland. Here, we present the results of a simplified thermo-mechanical model (STM) which allows one to study strain partitioning between two orogenic zones. We show that, if the two orogenic zones have the same mechanical properties, the viscosity of the décollement, which links them, controls the initial strain partitioning. During subsequent finite shortening, erosional processes determine the partitioning of strain rate. The presence of a weak structure in the inverted zone and of a low-viscosity décollement leads to initial strain concentration in the inverted track rather than in the collision zone and a progressive decrease in strain partitioning between the two orogenic zones. The STM results are in good agreement with results of a 2D finite-element model. We conclude that, in the western part of the Rhenohercynian Massif, simultaneous uplift and deformation within the Mid-German Crystalline Rise (the main collision zone) and the Ardenne Anticlinorium (the inverted zone) lead to interpreting this orogenic event as a case of vice tectonic rather than the propagation of a ‘wave of folding’ towards the Variscan front, as suggested by previous authors.     

煤层底板突水系数计算公式的探讨

根据从诸多濒临带压开采威胁的煤矿中得到大量的第一手资料,运用多元统计分析方法,揭示出了煤层底板突水这种地质现象的演化和特征的内在联系和规律,建立了矿压对煤层底板破坏深度的计算式。通过对以往煤层底板突水系数计算公式进行对比、分析、推理和总结,克服了以往计算公式的不足,继承和发展了公式的优点,得出了考虑因素较全面和较科学的突水系数计算式,从而为解决煤层底板隔水岩柱薄弱地带或断裂陷落柱薄弱地带的煤矿安全生产提供了一套行之有效的解决方法。这套公式在太原西峪煤矿和晋城矿务局(西区)得到了应用,证明是一种行之有效的方法。     

安宁河-则木河-小江带强震趋势的预测依据和应用问题

分析了近年沿安宁河一则木河一小江断裂带和大凉山断裂带出现的突出地震活动性、跨断层地壳形变和宏、微观异常现象。根据这些异常依据分析了强震趋势及预测应用问题，并进行了有益的思考。