Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.     

Optimal Filtering Algorithm for Stochastic 2-D FMM Ⅱ with Multiplicative Noise

1　Introduction　Inrecentyearstherehasbeengrowingresearchin terestinthetwo dimensional (2 D )systemtheory .The 2 Dsystemsmayfindapplicationsinareassuchasmarineseismicdataprocessingandimageprocessing .Althoughmoreandmorevaluableresultshavebeengained ,mos…     

居民收入与通信网络市场经济效益研究--以河北省通信网络为实例

利用Logisitic曲线模型和扩展支撑模型对居民可支配收入预测和单项消费预测，以河北省居民的收入及其消费支出为实例，研究了城镇居民和农民的可支配收入分配和单项边际消费倾向，合理建立了预测模型，并理论计算了1999～2003年的通信消费方面的边际消费倾向、预测了2004～2008年通信消费情况。最后，根据预测结果对通信网络建设提出了一些有价值的建议。     

A high resolution,multiproxy Late‐glacial record of climate change and intrasystem responses in northwest England

A lacustrine carbonate sequence from Hawes Water, Lancashire, UK, has been studied using stable isotopic, lithological, pollen and mineral magnetic analysis. The data reveal four abrupt climatic oscillations in the Late‐glacial Interstadial leading up to the onset of the Loch Lomond Stadial. The data also point to climatic warming relatively early within the stadial, ca. 12 500 GRIP yr, prior to the onset of the Holocene. The oxygen isotope record is taken as a signature of climate forcing against which the response of the lake‐system can be monitored. By adopting this approach it is revealed that the response of the biological system to the rapid climatic oscillations is non‐linear and primarily a function of the antecedent conditions. A significant end‐Devensian isotopic excursion (A) is matched by only minor changes in the cold‐adapted floras and faunas. During the warmer interstadial, the response of the biological ecosystem (events B–D) is clearly influenced by thresholds: major changes in the catchment vegetation associated with relatively minor oscillations in the isotopic signature. The stratigraphical patterns reveal significant lag effects between the onset of climate deterioration and resulting changes in vegetation. Copyright © 2002 John Wiley & Sons, Ltd.     

利用高光谱数据进行植被生化成分反演方法研究

高光谱数据包含着丰富光谱信息,能够定量地分析物质成分^[1]。由高光谱数据,可以运用多元逐步线性回归方法反演植被生化组分含量,从而达到监测植被生长状况的目的^[2]。本文具体介绍了多元逐步线性回归方法,及其在氮、木质素和纤维素含量估算中的应用。     

Hysteresis‐based analysis of overland metal transport

Introducing a concept of equivalent mass depth of flow, this study describes the phenomenon of non‐point source pollutant (metal) transport for pavement (or overland) flow in analogy with wave propagation in wide open channels. Hysteretic and normal mass rating curves are developed for runoff rate and mass of 12 dissolved and particulate‐bound metal elements (pollutants) using the rainfall‐runoff and water quality data of the 15 × 20 m² instrumented pavement in Cincinnati, USA. Normal mass rating curves developed for easy computation of pollutant load are found to be of a form similar to Manning's, which is valid for open channel flows. Based on the hysteresis analysis, wave types for dissolution and mixing of particulate‐bound metals are identified. The analysis finds that the second‐order partial‐differential equation normally used for metal transport does not have the efficacy to describe fully the strong non‐linear phenomena such as is described for various metal elements by dynamic waves. In addition, the proportionality concept of the popular SCS‐CN concept is extended for determining the potential maximum metal mass M_p of all the 12 elements transported by a rain storm and related to the antecedent dry period (ADP). For the primary metal zinc element, M_p is found to increase with the ADP and vice versa. Copyright © 2003 John Wiley & Sons, Ltd.     

Sediment transport in analogue flume models compared with real‐world sedimentary systems: a new look at scaling evolution of sedimentary systems in a flume

Evolution of sedimentary systems at large temporal and spatial scales cannot be scaled down to laboratory dimensions by conventional hydraulic Froude scaling. Therefore, many researchers question the validity of experiments aiming to simulate this evolution. Yet, it has been shown that laboratory experiments yield stratigraphic responses to allocyclic forcing that are remarkably similar to those in real‐world prototypes, hinting at scale independency with strong dependence on boundary conditions but weak dependence on the actual sediment transport dynamics. This paper addresses the dilemma by contrasting sediment transport rules that apply in the laboratory with those that apply in real‐world geological systems. It is demonstrated that the generation of two‐dimensional stratigraphy in a flume can be simulated numerically by the non‐linear diffusion equation. Sediment transport theory is used to demonstrate that only suspension‐dominated meandering rivers should be simulated with linear diffusion. With increasing grain‐size (coarse sand to gravel) and shallowness of river systems, the prediction of long‐term transport must be simulated by non‐linear, slope‐dependent diffusion to allow for increasing transport rates and thus change in stratigraphic style. To point out these differences in stratigraphic style, three stages in infill of accommodation have been defined here: (i) a start‐up stage, when the system is prograding to base level (e.g. the shelf edge) with no sediment flux beyond the base‐level point; (ii) a fill‐up stage, when the system is further aggrading while progressively more sediment is bypassing base level with the progression of the infill; and (iii) a keep‐up stage, when more than 90% of the input is bypassing the base level and less than 10% is used for filling the accommodation. By plotting the rate of change in flux for various degrees of non‐linearity (varying the exponent in the diffusion equation) it was found that the error between model and real‐world prototype is largest for the suspension‐dominated prototypes, although never more than 30% and only at the beginning of the fill‐up stage. The error reduces to only 10% for the non‐linear sandy‐gravelly and gravelly systems. These results are very encouraging and open up ways to calibrate numerical models of sedimentary system evolution by such experiments.     

Prediction of local scour around circular piles under waves using a novel artificial intelligence approach

Abstract

The scour phenomena around vertical piles in oceans and under waves may influence the structure stability. Therefore, accurately predicting the scour depth is an important task in the design of piles. Empirical approaches often do not provide the required accuracy compared with data mining methods for modeling such complex processes. The main objective of this study is to develop three data-driven methods, locally weighted linear regression (LWLR), support vector machine (SVR), and multivariate linear regression (MLR) to predict the scour depth around vertical piles due to waves in a sand bed. It is the first effort to develop the LWLR to predict scour depth around vertical piles. The models simulate the scour depth mainly based on Shields parameter, pile Reynolds number, grain Reynolds number, Keulegan–Carpenter number, and sediment number. 111 laboratory datasets, derived from several experimental studies, were used for the modeling. The results indicated that the LWLR provided highly accurate predictions of the scour depths around piles (R?=?0.939 and RMSE = 0.075). Overall, this study demonstrated that the LWLR can be used as a valuable tool to predict the wave-induced scour around piles.     

Freely floating-body simulation by a 2D fully nonlinear numerical wave tank

Nonlinear interactions between large waves and freely floating bodies are investigated by a 2D fully nonlinear numerical wave tank (NWT). The fully nonlinear 2D NWT is developed based on the potential theory, MEL/material-node time-marching approach, and boundary element method (BEM). A robust and stable 4th-order Runge–Kutta fully updated time-integration scheme is used with regriding (every time step) and smoothing (every five steps). A special φ_n-η type numerical beach on the free surface is developed to minimize wave reflection from end-wall and wave maker. The acceleration-potential formulation and direct mode-decomposition method are used for calculating the time derivative of velocity potential. The indirect mode-decomposition method is also independently developed for cross-checking. The present fully nonlinear simulations for a 2D freely floating barge are compared with the corresponding linear results, Nojiri and Murayama’s (Trans. West-Jpn. Soc. Nav. Archit. 51 (1975)) experimental results, and Tanizawa and Minami’s (Abstract for the 6th Symposium on Nonlinear and Free-surface Flow, 1998) fully nonlinear simulation results. It is shown that the fully nonlinear results converge to the corresponding linear results as incident wave heights decrease. A noticeable discrepancy between linear and fully nonlinear simulations is observed near the resonance area, where the second and third harmonic sway forces are even bigger than the first harmonic component causing highly nonlinear features in sway time series. The surprisingly large second harmonic heave forces in short waves are also successfully reproduced. The fully updated time-marching scheme is found to be much more robust than the frozen-coefficient method in fully nonlinear simulations with floating bodies. To compare the role of free-surface and body-surface nonlinearities, the body-nonlinear-only case with linearized free-surface condition was separately developed and simulated.