锚杆动测问题的数值解

建立了锚杆动测问题的有限元模型，并对锚杆中的缺陷进行了数值模拟，获得了位移场的数值解。对该解在时域和频域范围内的讨论表明，锚杆中的缺陷将引起动测曲线一系列的变化，为现场动测曲线的识别提供了依据。     

兴山县龙王嘴边坡稳定性分析与加固设计

龙王嘴边坡系坡高达70 m、坡角达70 °的高陡岩质边坡。分析了宜-秭公路石峡段龙王嘴高边坡变形的地质条件,在定量评价龙王嘴高边坡稳定性的基础上,进行了该高边坡的施工图加固设计。根据其特点将350 m长的坡段分为A,B,C三个区,分别采取预应力锚索与锚杆加固、挂网喷射混凝土支护和喷射混凝土支护等措施,实践证明,工程治理效果良好。     

超高强混凝土短柱抗震性能的试验研究

通过对12根剪跨比λ=2．0的超高强混凝土短柱在低周反复荷载下抗震性能的试验研究,分析了其破坏形态,并研究了轴压比和配箍率对试件滞回特性和抗震延性的影响,提出了满足一定延性要求（μ△≥3．0）超高强混凝土短柱的轴压比限值和箍筋加密区的最小配箍特征值的建议值。该值可为现行规范的修订提供参考。     

Flexural performances of prestressed high strength concrete piles reinforced with hybrid GFRP and steel bars

Abstract

This study developed prestressed high-strength concrete (PHC) piles reinforced with high-strength materials (glass fiber-reinforced polymer (GFRP) bars) for flexural performance enhancement. Flexural strengths and behaviors of PHC piles reinforced with hybrid GFRP and steel bars were experimentally investigated, respectively. Large-scale specimens with total lengths of 12,000?mm and diameters of 600?mm were constructed and tested under bending, accompanied by evaluation of effects of non-prestressed reinforcement type and longitudinal reinforcement ratio. J-factors were calculated to evaluate deformability of all the specimens. PHC piles reinforced with GFRP bars were demonstrated to have much higher flexural capacity than those reinforced with steel bars. Moreover, strains at the midspans of cross sections of all the specimens basically conformed to the assumption of plane section. Failure of PHC piles reinforced with GFRP bars was attributable to gradual concrete crushing, while that of PHC piles reinforced with steel bars resulted from steel yielding. Results of this study were expected to provide theoretical basis for wide engineering applications of PHC piles reinforced with hybrid GFRP bars and steel bars in marine structures.     

An analytical method for determining shear stiffness of an inclined grouted bolt installed across an open discontinuity

Summary The shear stiffness of a grouted, rock bolt intersecting a discontinuity controls the amount of shear movement that can occur for a given shear force. In this paper an analytical model is developed for estimating the shear stiffness of a single bolt as a function of bolt inclination, hole and bolt diameter, bolt, grout and rock Young's moduli, and aperture (opening) across the discontinuity, and sensitivity studies conducted to determine the most significant of these variables as predicted by the model.     

型钢高强混凝土柱轴压比限值的试验研究

通过20个型钢高强混凝土柱的低周反复加载试验对其受力性能进行了研究，分析了剪跨比、轴压比、配箍率以及混凝土强度对型钢高强混凝土柱延性的影响，提出了不同剪跨比、不同配箍率的型钢高强混凝土柱的轴压比限值。其中，剪跨比大于2．0的型钢高强混凝土柱的轴压比限值由大、小偏心界限破坏时力的平衡条件并结合试验结果确定，而剪跨比小于2．0的型钢高强混凝土柱的轴压比限值则通过与剪跨比大于2．0的型钢高强混凝土柱的延性对比加以确定。     

大唐国际东营一期49.5 MW风电场工程桩基施工及其原体试验

大唐国际东营风电一期工程拟建风电场场区位于东营市东部沿海区域,拟建场地上覆第四系地层,结构松散,厚度较大,工程性质较差,地基强度较低,不能满足重要建（构）筑物对其强度及变形的要求,且场地内的饱和粉土及砂土在地震影响烈度达Ⅶ度时将可能产生液化现象,因此需进行地基处理。根据现场岩土条件,拟采用预应力高强混凝土管桩（PHC）,需进行桩基原体试验。主要介绍了桩基原体试验施工过程、检测方法及试验成果等。     

Experimental and numerical investigations of stresses in a fully grouted rock bolts

Rock bolts are widely used for rock reinforcement in hard-rock mining and civil engineering since a long time. However the use of fully grouted rock bolts and cable bolts is limited in coal mines. In order to improve performance of the rock bolts as a supplementary roof support system for any type of roof condition in coal measured formations, it is necessary to have a good understanding of the behavior of the bolt–grout and grout–rock interactions as well as the mechanism of load transfer in rock bolts.As the performance of grouted bolts depends on bond strength, extensive laboratory pullout as well as pushout tests were conducted in the present investigations with the variations in the bolt diameters, length and cement–water mixing ratios of grout. The load–displacement curves were developed and were verified with the numerical results obtained from finite element analysis using ALGOR software.Numerical models were validated for pushout tests and a detailed analysis was carried out to know the displacement, stress, strain distribution along the bolt.     

Extrusion movements of a tunnel head reinforced by finite length bolts—a closed‐form solution using homogenization approach

An analytical model on the general behaviour of a tunnel head, reinforced by finite length bolts is proposed. This model is based on the homogenization method and spherical symmetry assumption. Despite its simplicity, and in consequence its limits of validity, it does allow a quick estimation of the key design parameters: frontal displacement, extension of decompressed zone, ground stresses and bolt tension, and constitutes thereby a very useful and handy tool for design engineers. In particular, the influence of the reinforcement length, as well as other important design parameters, are studied by the proposed model. The charts resulting from the parametric studies are directly applicable. Otherwise, the comparison to a 3D numerical model is also presented in this paper. The first results provide the validation of the analytical solution, at least in terms of average extrusion movements. Copyright © 2000 John Wiley & Sons, Ltd.     

高层高强钢组合偏心支撑框架抗震性能简化分析

高强钢组合偏心支撑钢框架是一种新型的抗震结构体系,为分析其抗震性能,利用ABAQUS有限元软件建立了简化分析模型。在验证该简化模型合理有效的基础上,建立了某十层算例的整体模型,施加竖向荷载的同时施加水平倒三角形循环荷载作用,进而分析了该算例的滞回性能。研究表明:本文提出的简化分析模型不仅可以较准确的模拟该结构体系的延性和抗侧刚度,还可以有效预测结构的变形分布和非线性性能。