Two sets of cooling experiments were run at atmospheric conditions for two anhydrous starting latitic and trachytic melts: 1) five cooling rates (25, 12.5, 3, 0.5, and 0.125 °C/min) between 1300° and 800 °C, and 2) a 0.5 °C/min cooling rate from 1300 °C with quench temperatures at 1200°, 1100°, 1000° and 900 °C. Trachytic run-products are invariably glassy. Nucleation is also suppressed in the latitic run-products at the three highest cooling rates. Conversely, in the 0.5 and 0.125 °C/min runs, latites have a crystal content of 90 vol.%. The phases are: plagioclase, clinopyroxene, glass and iron-bearing oxide (in order of abundance). The variable quench temperatures, investigated by coupling experiments with Pt wire and Pt capsule sample containers in set 2, again did not produce crystallization of trachyte, whereas latitic samples are characterized by 10 vol.% of oxides, pyroxenes and plagioclase (in order of appearance), at temperature < 1000 °C. Effects of (preferential) heterogeneous nucleation on sample holders, of superheating degree, and chemical species loss during cooling are absent for both melt compositions. The difference of solidification paths between these two silicate melts can be ascribed only to their small chemical differences. In comparison with calculated equilibrium conditions all the experimental latitic and trachytic run-products revealed strong kinetic effects, interpretable in the light of the nucleation theory. The glass-forming ability (GFA) of trachyte is higher, whereas their critical cooling rate (Rc) is lower (< 0.125 °C/min), in comparison to latitic melts (Rc > 0.5 °C/min). The experimental results carried out in this study can be applied to lava flows and domes; trachytic lavas are able to flow for longer period with respect to latitic ones in a metastable condition. Glass-rich terrestrial lavas, i.e. obsidians, can be the result of sluggish nucleation kinetics due to the relative high polymerisation of evolved silicate melts. 相似文献
In this note we investigated the effects of a thin visco-elastic mud layer on wave propagation. Within the framework of linear water-wave theory, analytical solutions are obtained for damping rate, dispersion relation between wave frequency and wave number, and velocity components in the water column and mud layer. The wave attenuation rate reaches a maximum value when the mud layer thickness is about the same as the mud boundary layer thickness. Heavier mud has a weaker effect on the wave damping. However, the wave attenuation rate does not always decrease as the elastic shear modulus increases. In the range of small values for elastic shear modulus, the wave attenuation can be amplified quite significantly. The current solutions are compared with experimental data with different wave conditions and mud properties. In general, good agreements are observed. 相似文献
A number of overflows from a large lava channel and tube system on the southwest rift zone of Mauna Loa were studied. Initial overflows were very low viscosity gas-rich phoehoe evidenced by flow-unit aspect ratios and vesicle sizes and contents. Calculated volumetric flow-rates in the channel range between 80 and 890 m3/s, and those of the overflows between 35 and 110 m3/s. After traveling tens to hundreds of meters the tops of these sheet-like overflows were disrupted into a surface composed of clinker and phoehoe fragments. After these 'a' overflows came to rest, lava from the interiors was able to break out on to the surface as phoehoe. The surface structure of a lava flow records the interaction between the differential shear rate (usually correlated with the volumetric flow-rate) and viscosity-induced resistance to flow. However, the interior of a flow, being better insulated, may react differently or record a later set of emplacement conditions. Clefts of toothpaste lava occurring within fields of clinker on proximal-type 'a' flows also record different shear rates during different times of flow emplacement. The interplay between viscosity and shear rate determines the final morphological lava type, and although no specific portion of lava ever makes a transition from 'a' back to phoehoe, parts of a flow can appear to do so. 相似文献
The viscosity of synthetic peridotite liquid has been investigated at high pressures using in-situ falling sphere viscometry by combining a multi-anvil technique with synchrotron radiation. We used a newly designed capsule containing a small recessed reservoir outside of the hot spot of the heater, in which a viscosity marker sphere is embedded in a forsterite + enstatite mixture having a higher solidus temperature than the peridotite. This experimental setup prevents spheres from falling before a stable temperature above the liquidus is established and thus avoids difficulties in evaluating viscosities from velocities of spheres falling through a partially molten sample.
Experiments have been performed between 2.8 and 13 GPa at temperatures ranging from 2043 to 2523 K. Measured viscosities range from 0.019 (± 0.004) to 0.13 (± 0.02) Pa s. At constant temperature, viscosity increases with increasing pressure up to 8.5 GPa but then decreases between 8.5 and 13 GPa. The change in the pressure dependence of viscosity is likely associated with structural changes of the liquid that occur upon compression. By combining our results with recently published 0.1 MPa peridotite liquid viscosities [D.B. Dingwell, C. Courtial, D. Giordano, A. Nichols, Viscosity of peridotite liquid, Earth Planet. Sci. Lett. 226 (2004) 127–138.], the experimental data can be described by a non-Arrhenian, empirical Vogel-Fulcher-Tamman equation, which has been modified by adding a term to account for the observed pressure dependence of viscosity. This equation reproduces measured viscosities to within 0.08 log10-units on average. We use this model to calculate viscosities of a peridotitic magma ocean along a liquid adiabat to a depth of 400 km and discuss possible effects on viscosity at greater pressures and temperatures than experimentally investigated. 相似文献
Pinch and swell structures occur where a more competent layer in a weaker matrix is subjected to layer-parallel extension. In this contribution, we use numerical models to explore the use of pinch and swell structure shape symmetry and asymmetry as a determinant of relative viscosity between layers. Maximum asymmetry is attained when the matrix viscosity on one side is subtly weaker than the competent layer, while the other side is significantly weaker.Our numerical results are directly applied to asymmetrically developed pinch and swell structures in exposed lower continental crust. Here, shape geometries observed in a shear zone comprised of plagioclase-dominated, garnet-dominated and mixed amphibole-plagioclase-dominated bands, reveals that the plagioclase-dominated band is the most competent band and is marginally stronger (2×) and significantly stronger (10–40×) than the fine grained garnet-dominated and mixed amphibole-plagioclase-dominated band, respectively. Based on the experimentally determined viscosity of a plagioclase-dominated material and quantitative microstructural analysis, the viscosity range of the natural rock bands is 2.8 × 1015 to 1.1 × 1017 Pa s. Consequently, the assumption that the experimentally-derived plagioclase flow law is an appropriate proxy for the middle to lower continental crust may lead to a viscosity over-estimation by up to forty times. 相似文献
Numerical investigations of 2D and 3D modes of large-scale convection in faulted aquifers are presented with the aim to infer possible transport mechanisms supporting the formation of thermal springs through fractured aquicludes. The transient finite elements models are based on idealized structural features that can characterize many hydrothermal systems. The sensitivity analysis of the fault permeability showed that faults cross-cutting the main regional flow direction allow groundwater to be driven laterally by convective forces within the fault planes. Therein thermal waters can either discharge along the fault traces or exit the fault through adjacent permeable aquifers. In the latter case, the resulting flow is helicoidally and transient. The location and the spacing between discharge areas can migrate with time, is not strictly constrained to the damage zones and reflects the wavelength of the multicellular regime in the fault zone.An illustrative example based on simplified structural data of the Lower Yarmouk Gorge (LYG) is presented. The numerical calculations indicate that crossing flow paths result from the coexistence of fault convection, developing for example along NE-SW oriented faults within the Gorge, and additional flow fields. The latter are induced either by topography NS gradients, e.g. perpendicular to the major axe of the Gorge, or by local thermal convection in permeable aquifers below the Eocene aquiclude. Sensitivity analysis of fault hydraulic conductivity (K) and the analytical solutions based on viscous-dependent Rayleigh theory show that K values between 2.3e−7 m/s and 9.3e– 7 m/s (i.e. 7 m/yr and 30 m/yr, respectively) favor coexisting transport processes. The uprising thermal plumes spread over several hundred meters forming clusters of springs, in agreement with observation, and which temperature fall within the measured ranges, i.e. 20 °C−60 °C. To some extent the models also reproduced the transient behavior of the spring temperature. Owing to the idealized nature of the presented models, the numerical results and the associated analytical solution can be applied to study the onset of thermal convection and resulting flow patterns of any fractured hydrothermal basin. 相似文献
Bentonite clay is a micro-inhomogeneous material, which consists of clay minerals (mainly montmorillonite), macro-grains (mainly quartz), water, air and others. Properties of the saturated bentonite clay are essentially characterized by the montmorillonite and water (i.e. montmorillonite hydrate). We analyze the molecular behavior of sodium montmorillonite hydrate Na1/3Al2[Si11/3Al1/3]O10(OH)2·nH2O by applying a molecular dynamics (MD) simulation method. And by using the MD results we calculate the swelling property of the montmorillonite hydrate, and compare with an experimental result. Next, by using the same MD procedure we treat a montmorillonite mineral with a large number of external water molecules to check the properties of the water. Here we treat pure- and salt-water. Then we calculate the diffusivity and viscosity of water molecules and Na+ and Cl− ions.
For extending the microscopic characteristics of constituent materials to a macroscopic seepage behavior of the micro-inhomogeneous material we apply a homogenization analysis (HA). That is, starting with the Navier–Stokes equation with distributed viscosity that is calculated by the former MD procedure we determine macroscopic permeability characteristics of bentonite for both cases of pure- and salt-water. Then, by using the permeability property we calculate long-term consolidation behavior of buffering clay, which is planed to be used for high-level radioactive waste (HLRW) management. Here the deformation is treated under the well-defined Cam clay model. 相似文献