Triaxial stress state deep in orogenic belts: an example from Turkey

A rare metachert pebble containing amphibole grains with microboudin structures in a wide range of orientations provides an opportunity to perform stress analysis in two orthogonal orientations on the foliation surface. The sample was analysed by the microboudin method to infer the triaxial stress state during microboudinage. Stress parameters proportional to the far-field differential stress were determined for sodic amphibole grains in the two orientations. The ratio of the stresses in the two orthogonal orientations (σ₁−σ₂)/(σ₁−σ₃) was calculated to be 0.64, indicating that σ₂ lies closer to the midpoint between σ₁ and σ₃ than to σ₃.     

Strain accumulation in sand due to cyclic loading: drained triaxial tests

Our aim is the prediction of the accumulation of strain and/or stress under cyclic loading with many (thousands to millions) cycles and relatively small amplitudes. A high-cycle constitutive model is used for this purpose. Its formulas are based on numerous cyclic tests. This paper describes drained tests with triaxial compression and uniaxial stress cycles. The influence of the strain amplitude, the average stress, the density, the cyclic preloading history and the grain size distribution on the direction and the intensity of strain accumulation is discussed.     

叶蛇纹岩脆性-半脆性破裂研究

利用Paterson气体介质高温高压流变仪对纯叶蛇纹岩在100~400MPa围压、25~700℃温度和10-5~1.5×10-6s-1应变速率下进行了三轴压缩变形实验。实验结果表明叶蛇纹石在低压条件下表现为脆性破裂,高压或脱水条件下表现为半脆性破裂。随着温度的增加,叶蛇纹石的强度显示逐渐降低的趋势;尤其在脱水条件下,温度的增加可导致叶蛇纹石强度大幅度地降低,而且此时预热时间对强度的影响比未发生脱水时更加显著。结合前人的研究并对比发现,围压在室温下的增加导致叶蛇纹岩强度增加;但在高温下围压的增加导致试样强度整体上降低,这很可能是试样内聚力的局部损失与韧性增强引起的。围压和温度的升高,以及断层面上流体的增加很可能会增加破裂面的韧性,从而减小摩擦系数。此外,叶蛇纹石并非以往人们所认为的那样具有极低的强度,其强度要比低温蛇纹石(如利蛇纹石和纤蛇纹石)的大得多,即便在高温(大约600℃)下差应力大于约600MPa和中-低温(≤400℃)下差应力大于约1000MPa时仍没有表现出明显屈服的迹象。在脱水条件下,蛇纹岩并没有发生脱水致脆,相反脱水使得试样的断裂行为变得更加温和些。因此,俯冲带蛇纹岩脱水更可能诱发其周围更加脆性的岩石发生地震而不是脱水的蛇纹岩本身发生地震。     

The penetration experiment to predict liquefaction resistance of reclaimed soils

The liquefaction resistance of the soils used to be estimated through the in situ tests, such as standard penetration test and cone penetration test; or by means of cyclic triaxial test in laboratory. However, both in situ tests and cyclic triaxial test are time-consuming and costly; this study introduces a quick and cost-effective method to evaluate the liquefaction resistance of soils under certain confining pressure in laboratory. A particular device modified from the conventional triaxial compression test apparatus, namely “Triaxial Cone Penetration Test”, was developed to obtain the peak values of cone resistance in soils so as to correlate the liquefaction resistance of the reclaimed soils evaluated by cyclic triaxial tests. The test result indicates a good correlation between the peak value of cone resistance and the corresponding cyclic stress ratio (CSR) at the state of initial liquefaction, in which the correlation for loose samples is better than that for dense samples. Besides, both peak values of cone resistance and corresponding CSR increase with fine content of soils reaches 10% and decreased with fine content varying between 10% and 50%. By examining the compositions of the soils with scanning electron microscopy and X-ray diffraction, it is found that the proportion and characteristics of the fines plays an important role on the liquefaction resistance of the reclaimed soils.     

压实粉土非线性应力-应变关系的试验研究

对京九线路基粉土用GDS三轴仪进行固结不排水剪试验,研究不同围压、含水量、压实度下压实粉土样的应力-应变关系。结果表明:压实粉土在低围压下为应变软化,高围压下为应变硬化,存在一个屈服应力;含水量和压实度对粉土强度和应力-应变关系影响显著,随着含水量的减小、压实度的增大,压实粉土样强度增大,应力-应变曲线上升。对围压小于屈服应力的应变软化曲线,用常规的土的软化关系式进行拟和;对围压大于屈服应力的应变硬化曲线,用邓肯-张模型进行拟和;这二者的结合能描述压实粉土的应力-应变关系曲线,效果良好。     

Suction-controlled triaxial testing: Laboratory procedures in relation to resistance envelope methods

In certain tropical slopes it appears possible that soil suction may play a significant role in maintaining stability. This communication outlines a laboratory suction-controlled triaxial test that can be undertaken to validate the threshold suction predicted by resistance envelope methods. It is shown that for two sites examined in St. Lucia, West Indies, the results from such a test confirm results obtained by use of resistance envelopes.     

A new criterion for strength of frozen sand under quick triaxial compression considering effect of confining pressure

The strength of frozen soils has been one of the most extensively studied aspects in frozen soil mechanics. When carrying out deep excavations using freezing methods, high stress states are often encountered. Therefore, the strength of frozen soils under high confining pressures is of major concern. This paper first reviews the present failure criteria for frozen soils, especially with regard to the effect of confining pressure on the strength. It is suggested that the strength consists of two components, cohesion and friction, and can be expressed by the Mohr–Coulomb criterion and in the framework of the Drucker–Prager criterion. However, these two components are both dependent on the stress state. Duncan’s equation for the friction angle is extended to frozen soils. A frozen Lanzhou fine sand is taken as study subject. The frozen sand is compressed at a high strain rate under three different temperatures and under a wide range of confining pressure. Experimental results have confirmed the generally recognized principle that the strength increases with the confining pressure up to certain value. Thereafter, it decreases with continued increase in confining pressure. Experimental data from our own tests and literature are fitted to the new criterion, which shows its validity.     

航空电磁发射线圈自感系数的精确计算

基于Maxwell计算螺线管电感量的方法,这里给出了适于编程计算单匝回线及多匝多层同轴空心线圈自感系数的的算法。根据航空电磁发射线圈的特点构造了几个模型,用以验证该计算方法的正确性,并表明了本文提供的算法和程序,可以为航空电磁线圈的优化设计提供理论和数据支持。     

Calibration of the parameters for a hardening–softening constitutive model using genetic algorithms

The present paper introduces a genetic algorithm-based optimization technique to calibrate a nonlinear strain hardening–softening constitutive model for soils using five material parameters. The efficiency of the proposed technique is analyzed through the use of different GA techniques. The effects of elitism, crossover, and mutation, as well as population size, on the performance of the conventional GAs for this problem are investigated. Micro-genetic algorithms (mGAs) are chosen and tested for different population sizes. The mGAs with a population size of five yields the optimal parameter values after fewer function evaluations and capture the overall simulated or experimental behavior at every point in stress–strain and strain paths in triaxial compression. The proposed calibration technique is validated through comparison with the traditional calibration technique.