对地方电视台转播CCTV时延的测定

讲述了同步广播卫星电视时间信号的测量方法和测量结果，获得了CCTV1、CCTV2通过同一颗卫星（亚太－1A）转播的时延差值为16333μs，测量精度在10ns以内；CCTV2、CCTV4分别经两颗卫星（亚太－1A、亚洲－Ⅱ）转播，在陕西天文台卫星地面接收站时延差值为1644．20μs，精度为50μs，并分析了影响时延差值和精度的原因。同时测量了地方电视台转播亚太－1A的CCTV信号与直接接收亚太－1A的CCTV信号的时延差值，其测量精度为0．1μs。这些结果为利用同步广播卫星的电视信号进行高精度的时间服务提供了参考依据。     

滇西动态重力网的分形特征及空间分辨力

介绍了用分形学描述地球物理观测网非均匀分布和联合应用分形特征与Ｓｈａｎｎｏｎ定理确定最佳网格距的方法。研究了滇西动态重力网的分形特征，它的分形维Ｄｆ＝１．２７，最佳网格距ｒ０＝２８ｋｍ。讨论了１９８６年至１９９４年间网区发生的８次Ｍｓ＞５．０级地震前重力场变化的可信性，指出这些变化的波长均大于１００ｋｍ，至少２倍于网的最小空间分辨力，因而是可信的     

大气层对GPS信号传播影响的规律之探讨──关于广州地区大气层对GPS系统定位定时影响问题研究之二

大气层对ＧＰＳ信号的传播有时间延迟作用，时廷将影响ＧＰＳ系统的定位和定时精度，且随气象因素的变化而变化．本文根据３年有关的气象资料，采用大气指数模型分析了广州地区大气层随昼夜变化、季节变化和太阳活动变化对ＧＰＳ信号传播时延影响的变化规律．分析得知，在信号垂直传播时，大气层对ＧＰＳ信号传播的影响，用距离表示．最大时为２．６９１ｍ，最小时也会产生１．９９３ｍ的误差；如果信号斜传播，误差因仰角因素将更大．     

卫星电视授时系统及精度估计

我国已建成短波、长波授时台，进行毫秒级、微秒级的时间服务．随着现代科技和经济的发展，上述方法已不能满足国家及国际交流的需要．本文提出卫星电视授时系统，同步卫星定位精度小于１１０ｍ，卫星授时精度为亚微秒。两原子钟利用卫星进行时刻同步，其精度与两原子钟的距离有关，相距３千多公里的两钟同步精度小于３５ｎｓ，相距数百公里的两原子钟同步精度小于２０ｎｓ     

低频扩频中伪随机序列产生方法的研究

伪随机序列的产生是实现BPC低频时码发播台扩展频谱技术升级的一个重要环节。针对BPC低频时码发播台的现有系统，提出了伪随机序列的产生方案，并对其性能作了分析。     

地球化学景观吸引子的发现及其意义

勘查地球化学对异常评价的最大不确定性源于对地球化学景观特性的认识不够。我们应用构造相空间的方法分析了浙江儒岙幅（1:5万）水系沉积物测量的Ag含量数据，揭示了地球化学景观是具有低维吸引子（DZ≈2．9）的混饨系统。这一发现将对勘查地球化学中采样密度的选择、地球化学场模拟、异常评价等根本性问题产生重大影响。     

On the practice of estimating fractal dimension

Coastlines epitomize deterministic fractals and fractal (Hausdorff-Besicovitch) dimensions; a divider [compass] method can be used to calculate fractal dimensions for these features. Noise models are used to develop another notion of fractals, a stochastic one. Spectral and variogram methods are used to estimate fractal dimensions for stochastic fractals. When estimating fractal dimension, the objective of the analysis must be consistent with the method chosen for fractal dimension calculation. Spectal and variogram methods yield fractal dimensions which indicate the similarity of the feature under study to noise (e.g., Brownian noise). A divider measurement method yields a fractal dimension which is a measure of complexity of shape.     

Travel time based approach for the assessment of vulnerability of karst groundwater: the Transit Time Method

Karst aquifers represent important water resources in many parts of the world. Unfortunately, karst aquifers are characterised by high contamination risks. This paper presents a travel time based method for the estimation of karst groundwater vulnerability. It considers (1) physics-based lateral flow within the uppermost weathered zone (epikarst) in a limestone-dominated region and (2) high velocities of vertical infiltration at discrete infiltration points (e.g. sinkholes) or lines (e.g. dry valleys, faults). Consequently, the Transit Time Method honours the actual flow path within the unsaturated zone of a karst aquifer system. A test site in Northern Jordan was chosen for the demonstration of the assessment technique, i.e. the catchment area of the Qunayyah Spring north of the capital Amman. The results demonstrate that zones of highest vulnerability lie within valleys and nearby main fault zones. It also reveals that regions, categorised as protected areas by other methods due to thick unsaturated zones, contribute to a major degree to the total risk.     

Influence of Structural Non-Stationarity of Surface Roughness on Morphological Characterization and Mechanical Deformation of Rock Joints

Summary Structural non-stationarity of surface roughness affects accurate morphological characterization as well as mechanical behaviour of rock joints at the laboratory scale using samples with a size below the stationarity threshold. In this paper, the effect of structural non-stationarity of surface roughness is investigated by studying the scale dependence of surface roughness and mechanical behaviour of rock joints. The results show that the structural non-stationarity mainly affects the accurate characterization of the surface roughness of the fracture samples. It also controls the amount and location of the contact areas during shear tests, which in turn affects the mechanical properties and asperity degradation of the samples. It is concluded that for accurate determination of the morphological and mechanical properties of rock joints at laboratory and field scales, samples with size equal to or larger than the stationarity threshold are required. Author’s address: Nader Fardin, Rock Mechanics Group, Department of Mining Engineering, Faculty of Engineering, University of Tehran, P.O. Box: 11365/4563, Tehran, Iran