Muon density measurements with the KASCADE central detector

Frequency distributions of local muon densities in high-energy extensive air showers (EAS) are presented as signature of the primary cosmic ray energy spectrum in the knee region. Together with the gross shower variables like shower core position, angle of incidence, and the shower sizes, the KASCADE experiment is able to measure local muon densities for two different muon energy thresholds. The spectra have been reconstructed for various core distances, as well as for particular subsamples, classified on the basis of the shower size ratio N_μ/N_e. The measured density spectra of the total sample exhibit clear kinks reflecting the knee of the primary energy spectrum. While relatively sharp changes of the slopes are observed in the spectrum of EAS with small values of the shower size ratio, no such feature is detected at EAS of large N_μ/N_e ratio in the energy range of 1–10 PeV. Comparing the spectra for various thresholds and core distances with detailed Monte Carlo simulations the validity of EAS simulations is discussed.     

隧道工程地质评价的内容和方法

结合工程隧道实际,首先阐述了隧道工程的基本地质环境和工程地质条件,然后针对隧道工程可能出现的不良地质现象和可采取的工程措施,从大气降水、围岩稳定、围岩压力、洞口稳定、隧道比选等角度探讨隧道工程地质评价的主要方法和一般内容,进行隧道工程地质评价,为隧道施工、支护提供了依据.     

Modelling of deformation response and chemo‐mechanical coupling in chalk

A constitutive relation is derived for describing the mechanical response of chalk. The approach is based on a phenomenological framework which employs chemo‐plasticity. The properties of the material are assumed to be affected by the physico‐chemical processes that occur through the interaction between the skeleton and the pore fluid. The underlying mechanism is discussed by invoking a micromechanical analysis. The performance of the framework is illustrated by examining the evolution of mechanical characteristics in the presence of different pore fluids. Copyright © 2006 John Wiley & Sons, Ltd.     

地下洞库勘察中的深斜孔钻探和压水试验技术

青岛市黄岛区拟建设海底地下油气储藏库,前期地质勘察工作要求施工倾角45°、深220m的取心钻孔4个,并在孔内分段进行压水试验.本文介绍了如何利用XY-4型金刚石小口径钻机施工基岩深斜孔及压水试验技术.     

Formation Pressure Evaluation Method for Single Well

The paper deals with the methods of formation pressure evaluation for a single well by using the very common ac-cepted parameters, such as drilling exponent , and flowline temperature , etc. which is part of compiling the end well report.     

Ultrahigh pressure macro diamonds from Copeton (New South Wales, Australia), based on Raman spectroscopy of inclusions

Mining of Cenozoic alluvial deposits at Copeton and Bingara (Eastern Australia) has produced two million macrodiamonds (0.25 ct median size). Raman spectroscopy is used to identify included minerals within uncut Copeton diamonds, with sealed chamber remnant pressures of 31.7 to 35.6 kbar for coesite, 13.6 and 22.7 kbar for clinopyroxene, and 7.6 kbar for grossular garnet. Assuming elastic behaviour, these values generate inclusion entrapment PT loci which intersect, restricting diamond formation conditions: from 250 °C, 43 kbar to 800 °C, 52 kbar. Larger than error (± 100 °C and ± 4 kbar), this range shows a systematic variation in inclusion composition with diamond zoning and N properties. Published research shows 1) Copeton and Bingara diamonds are unique, and 2) modern alluvium in the Bingara district carries mantle-formed garnet, captured by post-tectonic alkali basalt from an extensive diamondiferous ultrahigh pressure (UHP) terrane that stalled at depth because it is dominated by mafic eclogite. The combined Raman and geological results indicate two sets of subduction UHP diamond formation conditions/protolith are required, firstly cooler oceanic slab and secondly including higher temperature continental crust. The Copeton and Bingara stones are UHP macrodiamonds, and Carboniferous ⁴⁰Ar/³⁹Ar age dates on clinopyroxene inclusions should be interpreted as ages of crystallisation, representing the termination of subduction. The characteristic features of ruptured inclusions and etched percussion marks on Copeton and Bingara diamond indicate volcanic delivery to the earth's surface. Alluvial deposits elsewhere in Eastern Australia may carry similar diamond along with diamond of different origin.     

Impact evaluation on groundwater of the infiltration of an urban wastewater geopurification system placed over a detrital aquifer in a semiarid region (Spain)

Over a period of 4 years and 4 months, the geopurification installations at Dehesas de Guadix (Granada, Spain) were monitored to determine the impact on soil and groundwater of the controlled discharge of urban wastewater, and also to identify the best indicators of the entry of the recharged water into the aquifer. The installations are located in an area where the climate is Mediterranean sub-arid, with an average precipitation of less than 287 mm/year, and a rate of evapotranspiration that is almost three times greater. The system was controlled by determining the balance of majority nutrients and boron in the soil and in the groundwater, both at the points affected directly by the wastewater discharge and at others. The quantity of mass discharged was relatively large (COD 14,656 g/m², NO₃ 85 g/m², NO₂ 4 g/m², NH₄ 2,425 g/m², PO₄ 1,143 g/m², K 1,531 g/m², B 63 g/m²). It was observed that the elimination of nutrients within the soil (COD 97.5%, PO₄ 94.4%, K 59.17%, N _total 18.8%, B 12.69%) was very efficient except for the nitrogen, which nevertheless did not reach the groundwater, as it was eliminated at deep levels of the unsaturated zone. Only 12.69% of the boron was removed, and appreciable, increasing amounts of this element did reach the groundwater. Unexpectedly, none of the majority nutrients behaved as a reliable indicator of the impact on groundwater; despite this, the boron and the bicarbonate did clearly reflect the arrival of the recharged water, and are proposed as the best indicators.     

Determination of historical emission of heavy metals into the atmosphere: Celje case study

The research shows that in the Celje area (Slovenia), the historical anthropogenical emissions are 1,712 tons of Zn and 9.1 tons of Cd. For Zn, this value represents approximately 0.3% of the total Zn production in that area. Close to the former zinc smelting plant, the “Zn precipitation” has been estimated to be up to 0.036 mm. The 100-year Zn production left behind a heavily contaminated area with maximum concentrations of Zn of up to 5.6% in attic dust and 0.85% in the soil, and 456 mg/kg of Cd in attic dust and 59.1 mg/kg in the soil. The calculation of historical emissions is based on the data of heavy metals concentration in the attic dust at 98 sampling points and on the data from 19 measurement sites of the weight of total monthly air deposit. The main idea behind determining past emissions is that when the weight of the deposited dust on a small area is multiplied by the concentration of the element in that area, the mass of the polluter which has been transported to the place of interest by air can be calculated. If we sum up all the weight over the whole geochemical anomaly, we get the quantity of historical emissions.     

Mapping susceptibility of rainfall-triggered shallow landslides using a probabilistic approach

To prepare a landslide susceptibility map is essential to identify hazardous regions, construct appropriate mitigation facilities, and plan emergency measures for a region prone to landslides triggered by rainfall. The conventional mapping methods require much information about past landslides records and contributing terrace and rainfall. They also rely heavily on the quantity and quality of accessible information and subjectively of the map builder. This paper contributes to a systematic and quantitative assessment of mapping landslide hazards over a region. Geographical Information System is implemented to retrieve relevant parameters from data layers, including the spatial distribution of transient fluid pressures, which is estimated using the TRIGRS program. The factor of safety of each pixel in the study region is calculated analytically. Monte Carlo simulation of random variables is conducted to process the estimation of fluid pressure and factor of safety for multiple times. The failure probability of each pixel is thus estimated. These procedures of mapping landslide potential are demonstrated in a case history. The analysis results reveal a positive correlation between landslide probability and accumulated rainfall. This approach gives simulation results compared to field records. The location and size of actual landslide are well predicted. An explanation for some of the inconsistencies is also provided to emphasize the importance of site information on the accuracy of mapping results.