Pulsar Wind Nebulae in Egret Error Boxes

A remarkable number of pulsar wind nebulae (PWN) are coincident with EGRET γ-ray sources. X-ray and radio imaging studies of unidentified EGRET sources have resulted in the discovery of at least six new pulsar wind nebulae (PWN). Stationary PWN (SPWN) appear to be associated with steady EGRET sources with hard spectra, typical for γ-ray pulsars. Their toroidal morphologies can help determine the geometry of the pulsar which is useful for constraining models of pulsed γ-ray emission. Rapidly moving PWN (RPWN) with more cometary morphologies seem to be associated with variable EGRET sources in regions where the ambient medium is dense compared to what is typical for the ISM.     

HCN fluorescence on Titan

The HCN emission features near 3 μm recently detected by Geballe et al. (2003, Astrophys. J. 583, L39) are analyzed with a model for fluorescence of sunlight in the ν₃ band of HCN. The emission spectrum is consistent with current knowledge of the atmospheric temperature profile and the HCN distribution inferred from millimeter-wave observations. The spectrum is insensitive to the abundance of HCN in the thermosphere and the thousand-fold enhancement relative to photochemical models suggested by Geballe et al. (2003, Astrophys. J. 583, L39) is not required to explain the observations. We find that the spectrum can be matched with temperatures from 130 to 200 K, with slightly better fits at high temperature, contrary to the temperature determination of 130±10 K of Geballe et al. (2003, Astrophys. J. 583, L39). The HCN emission spectrum is sensitive to the collisional de-excitation probability, P₁₀, for the ν₃ state and we determine a value of 10⁻⁵ with an accuracy of about a factor of two. Analysis of absorption lines in the C₂H₂ν₃ band near 3 μm, detected in the same spectrum, indicate a C₂H₂ mole fraction near 0.01 μbar of 10⁻⁵ for P₁₀=10⁻⁴. The derived mole fraction, however, is dependent upon the value adopted for P₁₀ and lower values are required if P₁₀ at Titan temperatures is less than its room temperature value.     

Magnetic stratigraphy observed in ferromanganese crust

Summary. A sample of ferromanganese crust deposit (SCHW-1D) was cut into two sets of 1 mm slices for palaeomagnetic study. Alternating field and thermal demagnetization, and isothermal remanent magnetization analyses were performed on each thin slice. The results reveal the presence of a stable magnetism and both normal and reversed polarity intervals in the specimens. The observed polarity intervals cannot be confidently correlated with the geomagnetic polarity time-scale of the last 10 Myr due to the polarity overlap inherent in the sampling technique. But the results confirm the slow accretion rate of ferromanganese deposit determined by ¹⁰Be method and suggest potential use of ferromanganese deposits in palaeomagnetic and tectonic studies.     

Tensile stresses around boreholes due to transient fluid flow

We present solutions for the effective stress induced by gas flow through a porous solid into a borehole resulting from sudden pressure reduction. Tensile effective stress that exceeds the strength of the solid will lead to borehole failure. This has applications to the intentional creation of cavities, relevant to the efficient recovery of coalbed methane, and the avoidance of borehole stability problems in conventional gas production.     

Sonar acoustic facies and sediment distribution on an area of the deep ocean floor

Long-range sidescan sonar can be used to map sediment distributions over wide expanses of deep ocean floor. Seven acoustic facies that arise from differing sediment or rock types have been mapped over the low-relief Saharan continental rise and Madeira abyssal plain. These have been calibrated with sampling, profiling and camera studies and the facies can be traced confidently on a regional scale using the sidescan data. The mapping of the sediment distribution shows that a complex interplay of turbidity current and debris flow processes can occur at a continental rise/abysaal plain transition over 1000 km from the nearest continental slope.     

The second order characteristic condition for plastic flow

In this paper the second order characteristic (discontinuous bifurcation) condition is derived for the granular flow (fully plastic) equations. This second order bifurcation equation is shown to be formally identical to the first order localization requirement during steady elastoplastic deformation provided the elastic compliance tensor is substituted for the product of the plastic multiplier with the flow Hessian. For isotropic yield and flow functions the invariant form of the characteristic condition is given in detail, as well as an alternative expression in adapted co‐ordinates. The characteristic condition can be regarded as defining a hardening function which is maximized to identify the critical angles. When the method is applied to 3D Coulomb flow, Mohr's 3D fracture plane conditions are obtained uniquely. Copyright © 2003 John Wiley & Sons, Ltd.     

Fast iterative solution of large undrained soil‐structure interaction problems

In view of rapid developments in iterative solvers, it is timely to re‐examine the merits of using mixed formulation for incompressible problems. This paper presents extensive numerical studies to compare the accuracy of undrained solutions resulting from the standard displacement formulation with a penalty term and the two‐field mixed formulation. The standard displacement and two‐field mixed formulations are solved using both direct and iterative approaches to assess if it is cost‐effective to achieve more accurate solutions. Numerical studies of a simple footing problem show that the mixed formulation is able to solve the incompressible problem ‘exactly’, does not create pressure and stress instabilities, and obviate the need for an ad hoc penalty number. In addition, for large‐scale problems where it is not possible to perform direct solutions entirely within available random access memory, it turns out that the larger system of equations from mixed formulation also can be solved much more efficiently than the smaller system of equations arising from standard formulation by using the symmetric quasi‐minimal residual (SQMR) method with the generalized Jacobi (GJ) preconditioner. Iterative solution by SQMR with GJ preconditioning also is more elegant, faster, and more accurate than the popular Uzawa method. Copyright © 2003 John Wiley & Sons, Ltd.