A methodology to locate automatically limits or boundaries between different geological bodies in 2D electrical tomography is proposed, using a crest line extraction process in gradient images. This method is applied on several synthetic models and on field data set acquired on three experimental sites during the European project PALEOSIS where trenches were dug. The results presented in this work are valid for electrical tomographies data collected with a Wenner-alpha array and computed with an l1 norm (blocky inversion) as optimization method. For the synthetic cases, three geometric contexts are modelled: a vertical and a dipping fault juxtaposing two different geological formations and a step-like structure. A superficial layer can cover each geological structure. In these three situations, the method locates the synthetic faults and layer boundaries, and determines fault displacement but with several limitations. The estimated fault positions correlate exactly with the synthetic ones if a conductive (or no superficial) layer overlies the studied structure. When a resistive layer with a thickness of 6 m covers the model, faults are positioned with a maximum error of 1 m. Moreover, when a resistive and/or a thick top layer is present, the resolution significantly decreases for the fault displacement estimation (error up to 150%). The tests with the synthetic models for surveys using the Wenner-alpha array indicate that the proposed methodology is best suited to vertical and horizontal contacts. Application of the methodology to real data sets shows that a lateral resistivity contrast of 1:5–1:10 leads to exact faults location. A fault contact with a resistivity contrast of 1:0.75 and overlaid by a resistive layer with a thickness of 1 m gives an error location ranging from 1 to 3 m. Moreover, no result is obtained for a contact with very low contrasts (1:0.85) overlaid by a resistive soil. The method shows poor results when vertical gradients are greater than horizontal ones. This kind of image processing technique should be systematically used for improving the objectiveness of tomography interpretation when looking for limits between geological objects. 相似文献
Microalgae, a sustainable source of multi beneficial components has been discovered and could be utilised in pharmaceutical, bioenergy and food applications. This study aims to investigate the sugaring-out effect on the recovery of protein from wet green microalga, Chlorella sorokiniana CY1 which was assisted with sonication. A comparison of monosaccharides and disaccharides as one of the phaseforming constituents shows that the monosaccharides, glucose was the most suitable sugar in forming the phases with acetonitrile to enhance the production of protein(52% of protein). The protein productivity of microalgae was found to be significantly influenced by the volume ratio of both phases, as the yield of protein increased to 77%. The interval time between the sonication as well as the sonication modes were influencing the protein productivity as well. The optimum protein productivity was obtained with 10 s of resting time in between sonication. Pulse mode of sonication was suitable to break down the cell wall of microalgae compared to continuous mode as a lower protein yield was obtained with the application of continuous mode. The optimum condition for protein extraction were found as followed: 200 g/L glucose as bottom phase with volume ratio of I:1.25, 10 s of resting time for ultrasonication, 5 s of ultrasonication in pulse mode and 0.25 g of biomass weight. The high yield of protein about 81% could be obtained from microalgae which demonstrates the potential of this source and expected to play an important role in the future. 相似文献
Microalgae,a sustainable source of multi beneficial components has been discovered and could be utilised in pharmaceutical,bioenergy and food applications.This study aims to investigate the sugaring-out effect on the recovery of protein from wet green microalga,Chlorella sorokiniana CY1 which was assisted with sonication.A comparison of monosaccharides and disaccharides as one of the phaseforming constituents shows that the monosaccharides,glucose was the most suitable sugar in forming the phases with acetonitrile to enhance the production of protein(52% of protein).The protein productivity of microalgae was found to be significantly influenced by the volume ratio of both phases,as the yield of protein increased to 77%.The interval time between the sonication as well as the sonication modes were influencing the protein productivity as well.The optimum protein productivity was obtained with 10s of resting time in between sonication.Pulse mode of sonication was suitable to break down the cell wall of microalgae compared to continuous mode as a lower protein yield was obtained with the application of continuous mode.The optimum condition for protein extraction were found as followed:200g/L glucose as bottom phase with volume ratio of 1:1.25,10s of resting time for ultrasonication,5s of ultrasonication in pulse mode and 0.25g of biomass weight.The high yield of protein about 81% could be obtained from microalgae which demonstrates the potential of this source and expected to play an important role in the future. 相似文献
Natural Resources Research - Blasting is the predominant rock fragmentation technique in civil constructions, underground and surface mines. Flyrock is the unwanted throw of rock fragments during... 相似文献
A fast inversion technique for the interpretation of data from resistivity tomography surveys has been developed for operation on a microcomputer. This technique is based on the smoothness-constrained least-squares method and it produces a two-dimensional subsurface model from the apparent resistivity pseudosection. In the first iteration, a homogeneous earth model is used as the starting model for which the apparent resistivity partial derivative values can be calculated analytically. For subsequent iterations, a quasi-Newton method is used to estimate the partial derivatives which reduces the computer time and memory space required by about eight and twelve times, respectively, compared to the conventional least-squares method. Tests with a variety of computer models and data from field surveys show that this technique is insensitive to random noise and converges rapidly. This technique takes about one minute to invert a single data set on an 80486DX microcomputer. 相似文献
Water tank experiments were performed in order to investigate the behaviour of currents in pockmarks. A particle-seeded flow was visualised and quantified with the aid of the particle tracking velocimetry technique. The employed analogue pockmark is a 1:100 idealised scale model of a natural pockmark, while the highest Reynolds number in the experiments was one order of magnitude smaller than in nature. Interaction of the flow with the pockmark geometry resulted in an upwelling current downstream of the pockmark centre, along with enhanced water turbulence in the depression. Scaling-up the experimental measurements, it is found that the upwelling would be capable of preventing the settling of particles as large as very fine sand. Furthermore, the increased turbulence would support the suspended fine material, which can thus be transported away before settling. The net effect for a variable-direction near-bed current over long periods of time would be to winnow the settling sediments and reduce the sedimentation rate in pockmarks. These mechanisms may be responsible for the observed lack of sediment infill and the typical presence of relatively coarser sediments inside pockmarks compared to the surrounding bed. In contrast, sediments transported as bedload are likely to be deposited in pockmarks because of the weakening of near-bed currents as well as lateral flow convergence associated with the upwelling. Bedload, however, may not be the dominant mode of sediment transport in areas covered by cohesive sediments, where pockmarks are found. 相似文献
A validation experiment, carried out in a scaled field setting, was attempted for the long electrode electrical resistivity tomography method in order to demonstrate the performance of the technique in imaging a simple buried target. The experiment was an approximately 1/17 scale mock‐up of a region encompassing a buried nuclear waste tank on the Hanford site. The target of focus was constructed by manually forming a simulated plume within the vadose zone using a tank waste simulant. The long electrode results were compared to results from conventional point electrodes on the surface and buried within the survey domain. Using a pole‐pole array, both point and long electrode imaging techniques identified the lateral extents of the pre‐formed plume with reasonable fidelity but the long electrode method was handicapped in reconstructing vertical boundaries. The pole‐dipole and dipole‐dipole arrays were also tested with the long electrode method and were shown to have the least favourable target properties, including the position of the reconstructed plume relative to the known plume and the intensity of false positive targets. The poor performance of the pole‐dipole and dipole‐dipole arrays was attributed to an inexhaustive and non‐optimal coverage of data at key electrodes, as well as an increased noise for electrode combinations with high geometric factors. However, when comparing the model resolution matrix among the different acquisition strategies, the pole‐dipole and dipole‐dipole arrays using long electrodes were shown to have significantly higher average and maximum values within the matrix than any pole‐pole array. The model resolution describes how well the inversion model resolves the subsurface. Given the model resolution performance of the pole‐dipole and dipole‐dipole arrays, it may be worth investing in tools to understand the optimum subset of randomly distributed electrode pairs to produce maximum performance from the inversion model. 相似文献
Evapotranspiration estimation is of crucial importance in arid and hyper-arid regions, which suffer from water shortage, increasing dryness and heat. A modeling study is reported here to cross-station assessment between hyper-arid and humid conditions. The derived equations estimate ET0 values based on temperature-, radiation-, and mass transfer-based configurations. Using data from two meteorological stations in a hyper-arid region of Iran and two meteorological stations in a humid region of Spain, different local and cross-station approaches are applied for developing and validating the derived equations. The comparison of the gene expression programming (GEP)-based-derived equations with corresponding empirical-semi empirical ET0 estimation equations reveals the superiority of new formulas in comparison with the corresponding empirical equations. Therefore, the derived models can be successfully applied in these hyper-arid and humid regions as well as similar climatic contexts especially in data-lack situations. The results also show that when relying on proper input configurations, cross-station might be a promising alternative for locally trained models for the stations with data scarcity.
Improving the accuracy of flood prediction and mapping is crucial for reducing damage resulting from flood events. In this study, we proposed and validated three ensemble models based on the Best First Decision Tree (BFT) and the Bagging (Bagging-BFT), Decorate (Bagging-BFT), and Random Subspace (RSS-BFT) ensemble learning techniques for an improved prediction of flood susceptibility in a spatially-explicit manner. A total number of 126 historical flood events from the Nghe An Province (Vietnam) were connected to a set of 10 flood influencing factors (slope, elevation, aspect, curvature, river density, distance from rivers, flow direction, geology, soil, and land use) for generating the training and validation datasets. The models were validated via several performance metrics that demonstrated the capability of all three ensemble models in elucidating the underlying pattern of flood occurrences within the research area and predicting the probability of future flood events. Based on the Area Under the receiver operating characteristic Curve (AUC), the ensemble Decorate-BFT model that achieved an AUC value of 0.989 was identified as the superior model over the RSS-BFT (AUC = 0.982) and Bagging-BFT (AUC = 0.967) models. A comparison between the performance of the models and the models previously reported in the literature confirmed that our ensemble models provided a reliable estimate of flood susceptibilities and their resulting susceptibility maps are trustful for flood early warning systems as well as development of mitigation plans. 相似文献