Interplay between erosion and tectonics in the Western Alps

Bedrock fission‐track analysis, high‐resolution petrography and heavy mineral analyses of sediments are used to investigate the relationships between erosion and tectonics in the Western Alps. Along the Aosta Valley cross‐section, exhumation rates based on fission‐track data are higher in the fault‐bounded western block than in the eastern block (0.4–1.5 vs. 0.1–0.3 mm yr⁻¹). Erosion rates based on the analysis of bed‐load in the Dora Baltea drainage display the same pattern and have similar magnitudes in the relative sub‐basins (0.4–0.7 vs. 0.04–0.08 mm yr⁻¹). Results highlight that climate, relief and lithology are not the controlling factors of erosion in the Western Alps. The main driving force behind erosion is instead tectonics that causes the differential upward motion of crustal blocks.     

Risk assessment strategies for the reactivation of earth flows in the Northern Apennines (Italy)

The aim of this paper is to analyze the reactivation mechanism of ancient earth flows, with a view to gleaning information that can subsequently be utilized to formulate a risk-reduction strategy. All considerations made herein are the result of direct experience and observation of actual events which have occurred over the past few decades in the Northern Apennines. Particular attention has been paid to the analysis of the evolution of landslides during actual reactivation, acknowledging a typical, recurring succession of events that precede the failure of the slope. The hazard assessment of these large landslide bodies, which are of slope scale, constitutes a thorny problem, especially in view of the inapplicability of traditional deterministic models such as limit equilibrium stability analysis. Nevertheless, a site-specific assessment of probability of reactivation of these large and ancient earth flows is fundamental to effective land-use planning.     

Pumpellyite in Low-grade Metamorphism

The regional metamorphism of the Kant? Mountains in Japan producedrocks of the following facies, with rising temperature: chloritefacies, pumpellyite-chlorite facies, glauco-phane-schist facies,and greenschist facies. This relationship is compared with theprogressive metamorphic zones in other regions where pumpellyitehas been found. Almost similar relations appear to hold in manymetamorphic terrains. Pumpellyites in glaucophanitic metamorphicterrains have, generally, low Fe'/R'R ratios. Physical andchemical conditions responsible for the formation of pumpellyiteare also discussed.     

Fluid inclusion studies of the Abawso gold prospect,near the Ashanti Belt,Ghana

The major Ghanaian lode gold deposits are preferentially aligned along the western and eastern contacts of the Kumasi Basin with the Ashanti and Sefwi Belts, respectively. The investigated area of the Abawso small-scale concession, covering the workings of the old Ettadom mine, is situated 3 km west of the lithological contact of the Birimian metavolcanic rocks of the Akropong Belt in the east with the Birimian metasedimentary rocks of the Kumasi Basin in the west. The rocks of the Abawso concession represent a steeply NW-dipping limb of a SE-verging anticline with an axis plunging to the SW. Quartz veining occurs predominantly in the form of en échelon dilatational veins along NNE–SSW-striking shear zones of a few metres width and shows evidence of brittle and ductile deformation. Also stockwork-style quartz veining occurs in the vicinity of the main shaft of the old Ettadom mine. Hydrothermal alteration includes sericitisation, sulphidation and locally carbonatisation. The auriferous quartz veins mainly follow the trend of brittle to ductile deformed quartz veins; however, some occur in stockwork. Fluid inclusion studies reveal a large number of H₂O inclusions along intragranular trails in auriferous quartz vein samples, as well as an overall dominance of H₂O and H₂O-CO₂ inclusions over CO₂ inclusions. Textural observations and physico-chemical fluid inclusion properties indicate post-entrapment modifications for all quartz vein samples due to grain boundary migration recrystallisation. This process is interpreted to be responsible for the generation of the CO₂ inclusions from a H₂O-CO₂ parent fluid. In comparison with mineralisation at the Ashanti and Prestea deposits, which are characterised by CO₂±N₂ inclusions, the observed inclusion assemblage may be due to a shallower crustal level of mineralisation, or different degrees and styles of recrystallisation, or a less pronounced development of laminated quartz veins due to comparably restricted pressure fluctuations. Furthermore, the microthermometric observations allow the reconstruction of a possible retrograde P-T path, depicting near-isothermal decompression in the P-T range of the brittle/ductile transition.Editorial handling: E. Frimmel     

Kinetics and Equilibrium Sorption Studies of 4-Nitrophenol on pyrolyzed and activated oil shale residue

Sorption of the organic pollutant 4-nitrophenol (4-NP) by pyrolyzed and activated Jordanian oil-shale was studied. Pyrolyzed oil shale was prepared using a fluidized bed reactor at 520 °C in the presence of nitrogen. Physical activation was carried out by treating the pyrolyzed oil shale with CO₂ at 830 °C, while chemical activation was achieved by using KOH and ZnCl₂ as impregnating agents. Batch kinetics and isotherm studies were conducted to evaluate the sorption process. Effects of contact time, initial sorbate concentration, sorbent concentration, temperature, pH and inorganic salts (NaCl and KCl) on the sorption process by the different sorbents were considered. Chemically activated oil shale, pretreated with ZnCl₂, gave the highest uptake of 4-NP. The isotherm experimental data fit reasonably well to Langmuir, Freundlich and Redlich-Paterson models. Three kinetic models, namely the Morris-Weber, Lagergren, and Pseudo-Second-Order model (PSOM), were applied to represent the experimental results for both pyrolyzed and ZnCl₂-oil shale sorbents.     

Dauphiné twinning and texture memory in polycrystalline quartz. Part 3: texture memory during phase transformation

Samples of quartz-bearing rocks were heated above the α (trigonal)–β (hexagonal) phase transformation of quartz (625–950°C) to explore changes in preferred orientation patterns. Textures were measured both in situ and ex situ with neutron, synchrotron X-ray and electron backscatter diffraction. The trigonal–hexagonal phase transformation does not change the orientation of c- and a-axes, but positive and negative rhombs become equal in the hexagonal β-phase. In naturally deformed quartzites measured by neutron diffraction a perfect texture memory was observed, i.e. crystals returned to the same trigonal orientation they started from, with no evidence of twin boundaries. Samples measured by electron back-scattered diffraction on surfaces show considerable twinning and memory loss after the phase transformation. In experimentally deformed quartz rocks, where twinning was induced mechanically before heating, the orientation memory is lost. A mechanical model can explain the memory loss but so far it does not account for the persistence of the memory in quartzites. Stresses imposed by neighboring grains remain a likely cause of texture memory in this mineral with a very high elastic anisotropy. If stresses are imposed experimentally the internal stresses are released during the phase transformation and the material returns to its original state prior to deformation. Similarly, on surfaces there are no tractions and thus texture memory is partially lost.